• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.77-81
• /
• 2017

Pulse electroplating of Ni-P alloy was studied to fulfill the material requirement to the advanced vertical probe tip in wafer probe card. The major concerns are for the electrical conductivity and yield strength. Plating parameters such as current density, duty cycle and solution components were examined to obtain the nanocrystal structure and proper percentage of phosphorus, leading to how to control the nanocrystal grain growth and precipitation of $Ni_3P$ after heat treatment. Among the parameters, the amount of phosphorus acid was the main factor affecting on the grain size and sheet resistance, and the amount of 0.1 gram was appropriate. Since hardness in Ni-P alloy is increased by as-plated nanocrystal structure plus precipitation of $Ni_3P$, the concentration of P less than 15 at% was better choice for the grain coarsening without minus in hardness value. The following heat treatment made grain growth and dispersion of precipitates adjustable to meet the target limit of resistance of $100m{\Omega}$ and hardness number of over 1000Hv. The Ni-P alloy will be a candidate for the substitute of the conventional probe tip material.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.114-114
• /
• 2011

Aluminum oxide surface에 palladium 전처리 공정을 이용하여 무전해 Ni-P 도금을 진행하였다. Ni-P도금액을 산성(pH 4.8~5.3)용액과 알칼리(pH 9~10)용액에 따른 각각의 도금 특성을 평가하였다. 또한 다양한 공정조건(온도, pH, 두께 등...)에서의 도금 특성과 미세구조를 분석하여 $Al_2O_3$막에 적합한 Ni-P 도금액과 공정조건을 개발하였다. 산성 Ni-P 도금액의 경우 pH 5.3, $90^{\circ}C$의 도금 조건에서 phosphorous 12.1 wt.%, 도금속도 274nm/min.의 Ni-P 도금막을 얻을 수 있었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.1
• /
• pp.25-31
• /
• 2010

In this study, we investigated the morphology and thermal stability of interfacial phases in joint between lead free solder(Sn-3.0Ag-0.5Cu) and electroless Ni-W-P under bump metallizations(UBM) with different tungsten contents as a function of thermal aging. Content of phosphorus of each deposits was fixed at 8 wt.%, and content of tungsten was variated each 0, 3, 6 and 9 wt.%. Specimens were prepared by reflowing at $255^{\circ}C$, aging range was $200^{\circ}C$ and up to 2 weeks. After reflow process, in the electroless Ni(W)-P/solder joint, the interfacial intermetallic compound(IMC) was showed both $(Cu,Ni)_6Sn_5$ and $(Ni,Cu)_3Sn_4$. UBM and generated IMC at the interface of lead free solder was proportionally increased with aging time. The thickness of IMC was increased because the generation rate of $Ni(W)_3P$ decreased with increasing contents of W.

• Korean Journal of Crystallography
• /
• v.15 no.1
• /
• pp.35-39
• /
• 2004

Two new nickel vanadium borophosphate cluster compounds, $(NH_4)_{10}[Ni(H_2O)_5]_4[V_2P_2BO_{12}]_6{\cdot}nH_2O$ (1) and $(NH_4)_{3.5}(C_3H_{12}N_2)_{3.5}[Ni(H_2O)_6]_{1.25}{[Ni(H_2O)_5]_2[V_2P_2BO_{12}]_6{\cdot}nH_2O$ (2) have been synthesized and structurally characterized. Inter-diffusion methods were employed to prepare the compounds. The cluster anion $[(NH_4)\;{\supset}\;V_2P_2BO_{12}]_6$ is used as a building unit in the synthesis of new compounds containing $Ni(H_2O){^{2+}_5}$ in the presence of pyrazine and 1,3-diaminopropane. Compounds contain isolated cluster anions with general composition ${[Ni(H_2O)_5]_n[(NH_4)\;{\supset}\;V_2P_2BO_{12}]_6}^{-(17-2n)}$ (n = 2, 4). Crystal data: $(NH_4)_{10}[Ni(H_2O)_5]_4[V_2P_2BO_{12}]_6{\cdot}nH_2O$, monoclinic, space group C2/m (no. 12), a = 27.538(2) ${\AA}$, b = 20.366(2) ${\AA}$, c = 11.9614(9) ${\AA}$, ${\beta}$ = 112.131(1)$^{\circ}$, Z = 8; $(NH_4)_{3.5}(C_3H_{12}N_2)_b[Ni(H_2O)_6]_{3.5}{[Ni(H_2O)_5]_2[V_2P_2BO_{12}]_6{\cdot}nH_2O$, triclinic, space group P-1 (no. 2), a = 17.7668(9) ${\AA}$, b = 17.881(1) ${\AA}$, c = 20.668(1) ${\AA}$, ${\alpha}$ = 86.729(1)$^{\circ}$, ${\beta}$ \ 65.77(1)$^{\circ}$, ${\gamma}$ = 80.388(1)$^{\circ}$, Z = 2.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.6
• /
• pp.260-268
• /
• 2015

The thermal barrier coating (TBC) for inner wall of liquid-fuel rocket combustor consists of NiCrAlY as bonding layer and $ZrO_2$ as a top layer. In most case, the plasma spray coating is used for TBC process and this process has inherent possibility of cracking due to large difference in thermal expansion coefficients among bonding layer, top layer and metal substrate. In this paper, we suggest crack-free TBC process by using a precise electrodeposition technique. Electrodeposited Ni-P/Cr double layer has similar thermal expansion coefficient to the Cu alloy substrate resulting in superior thermal barrier performance and high temperature oxidation resistance. We studied the effects of phosphorous concentrations (2.12 wt%, 6.97 wt%, and 10.53 wt%) on the annealing behavior ($750^{\circ}C$) of Ni-P samples and Cr double layered electrodeposits. Annealing temperature was simulated by combustion test condition. Also, we conducted SEM/EDS and XRD analysis for Ni-P/Cr samples. The results showed that the band layers between Ni-P and Cr are Ni and Cr, and has no formed with heat treatment. These band layers were solid solution of Cr and Ni which is formed by interdiffusion of both alloy elements. In addition, the P was not found in it. The thickness of band layer was increased with increasing annealing time. We expected that the band layer can improve the adhesion between Cr and Ni-P.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.3
• /
• pp.73-81
• /
• 2015

Chloride plating solution was fabricated by dissolving metal Ni powders in solution with HCl and deionized water. Effects of deposition conditions on the properties of Ni films electrodeposited from chloride baths were studied. Current efficiency of Ni films electrodeposited from the baths containing saccharin was decreased with increasing the current density. Residual stress of Ni thin films ware measured to be about 230 ~ 435 MPa in the range of current density of $10{\sim}25mA/cm^2$. Cathode current efficiency in baths without saccharin was initially increased with increasing pH, while it was decreased with increasing pH further. Cathode current efficiency in baths with saccharin (except at pH 2) exhibited less 10 ~ 20% than that in baths without saccharin. Residual stress of Ni films electrodeposited from baths without saccharin was measured to be 388 ~ 473 MPa in the range of pH 2 ~ pH 5 and then was increased to 551 MPa at pH 6. On the other hand, residual stress of Ni films electrodeposited from baths with saccharin was increased with increasing pH. Surface morphology was strongly affected by the change of current density, but slightly by solution pH and addition of saccharin.

• Tribology and Lubricants
• /
• v.26 no.1
• /
• pp.68-72
• /
• 2010

A ceramic coating is a surface treatment method that is being used widely in the industrial field, recently. Ni-P plating is also being used widely because of its corrosion resistance and low cost. An anodizing method is applicable to aluminum alloy. An anodizing method generates a thick oxide layer on the surface and then, that heightens hardness and protects the surface. These surface treatments are applied to various mechanical components and treated surfaces relatively move one another. In this study, tribological characteristics of Ni-P plating and TiAlN coating on anodized Al alloy are compared. The counterpart, anodized Al alloy, is worn out abrasively by Ni-P plating and TiAlN coating that have higher hardness. Abrasively worn debris accumulated on the surfaces of Ni-P plating and TiAlN coating, and then transferred layer is formed. This transferred layer affects the amplitude of variation of friction coefficient, which is related to noise and vibration. The amplitude of variation of friction coefficient of Ni-P plating is lower than those of TiAlN coating during the tests.

• Corrosion Science and Technology
• /
• v.13 no.3
• /
• pp.107-111
• /
• 2014

Electroless plated Ni-Co-P films have been used to suppress the electromagnetic waves from magnetic recording media, and the suppression is known to be achieved with films made with optimized plating composition and plating condition. Effects of complexing agents on the deposition rate and bath stability of Ni-Co-P film were studied using sodium citrate, sodium tartrate and multi-complex agents containing both of them. Deposition of electroless Ni-Co-P platings was dependent upon the complexing agents. Deposition rate was twice when using sodium tartrate compared to that using sodium citrate. And it was slightly slower with multi-complex agents than with sodium tartrate, bath stability being declined in the former. Deposition rate increased with increasing pH until pH 11. Excellent bath stability and good deposition rate were obtained using multi-complex agent as sodium citrate 0.10 mol/L and sodium tartrate 0.15 mol/L in the electroless Ni-Co-P plating films.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.10
• /
• pp.495-499
• /
• 2004

Characteristics of ohmic Ni/Si/Ni contacts to n-type 4H-SiC are investigated systematically. The ohmic contacts were formed by annealing Ni/Si/Ni sputtered sequentially The annealings were performed at 950℃ using RTP in vacuum ambient and N₂ ambient, respectively. The specific contact resistivity(p/sub c/), sheet resistance(R/sub s/), contact resistance (R/sub c/) transfer length(L/sub T/) were calculated from resistance(R/sub T/) versus contact spacing(d) measurements obtained from TLM(transmission line method) structure. While the resulting measurement values of sample annealed at vacuum ambient were p/sub c/ = 3.8×10/sup -5/Ω㎠, R/sub c/ = 4.9 Ω and R/sub T/ = 9.8 Ω, those of sample annealed at N₂ ambient were p/sub c/ = 2.29×10/sup -4/Ω㎠, R/sub c/ = 12.9 Ω and R/sub T/ = 25.8 Ω. The physical properties of contacts were examined using XRD 3nd AES. The results showed that nickel silicide was formed on SiC and Ni was migrated into SiC. This result indicates that Ni/Si/Ni ohmic contact would be useful in high performance electronic devices.

• Corrosion Science and Technology
• /
• v.6 no.5
• /
• pp.257-260
• /
• 2007

In order to further improve the corrosion resistance and wear resistance of the Ni-P coatings of electroless plating, electroless Ni-P/n-$Al_2O_3$ composite deposits were prepared by adding some nano $Al_2O_3$ Particles in Ni-P plating bath. The bath composition and proproties were studied in this paper. The orthogonal test was applied in order to get the new composite solution, taking the initial stable potential as evaluation standard and considering the elements correlation at the same time. The processing parameters have been optimized by single factor experiment in which the depositing speed was chosen as the evaluation standard. The results showed that the process is stable and the composite Ni-P/n-$Al_2O_3$ deposits werebright and smooth, whose hardness and corrosion resistance are much better than simple Ni-P coatings. Furthermore the surface appearance and structure of the composite Ni-P/n-$Al_2O_3$ coating were investigated by SEM and XRD method. It was proved that the coating surface is typical cystiform cells and its structure is amorphous. All test results ofcomposite coating showed that all various physical coating properties had been improved by adding nano-particles. The hardness of optimal coating is more than 600HV and increases to 1000HV after heat-treating, and its hardness is 20~50% higher than Ni-P coating. The rust points appeared in 200 hour by immersing the coating into the 10%HCl solution and the corrosive speed is $3{\times}10^{-3}mg/(cm^2{\cdot}h)$which was obtained after 300 hour. In the same condition Ni-P coating is $5.6{\times}10^{-3}mg/(cm^2{\cdot}h)$. The salt spray resistance of the layers can exceed 600h with the thickness $20{\mu}m$.