• 환경위생공학
• /
• 제18권3호통권49호
• /
• pp.35-42
• /
• 2003

The electric resistance and constant current were investigated on the nickel-thallium-phosphorus alloy deposits by electroless-plating. The Ni-Tl-P alloy deposits were achieved with a bath using sodium hypophosphit as the reducing agent and sodium citrate as the comlexing agent. The basic plating solution is composed of 0.1M NiSO$_4$, 0.005${\sim}$0.0IM Tl$_2$S0$_4$, 0.1${\sim}$O.2M sodium hypophosphite and 0.02${\sim}$O.IM sodium citrate and the plating condition were pH 5${\sim}$6, temperrature 80$_4$90${\circ}$C. The results obtained are summarized as follows: 1) The crystal structure of deposit was amorphous structure as deposited state, became microcrystallized centering on Ni(111) plane by heat treatment at 200${\circ}$C, and grew as polycrystalline Ni, Ni$_3$P, Ni$_5$p$_2$,Tl, etc. by heat treatment higher than 350${\circ}$C. The grain size of plated deposits was grown up to 28.3~42.0nm by heat treatment for 1hour at 500${\circ}$C. 2) The electrical resistivity showed a comparatively high value of 192.5$_4$208.3 ${\mu}$${\Omega}$Cm and its thermal stability was great with resistivity value less than 0.22% in the thermal surroundings of 200${\circ}$C. 3) Ni-Tl-P alloy deposit showed such good constant current-making-effect in the variation of electric voltage, heat treatment temperature, and the composition of the deposit that it can be put to practical use as the matter of constant current device.

• 열처리공학회지
• /
• 제27권1호
• /
• pp.1-9
• /
• 2014

For connector material applications, the influence alloying elements of Mn, Cr, Fe, and Ti and cold rolling reduction on the mechanical property, electrical conductivity and bendiability of Cu-Ni-Si-P alloy was investigated. The hot rolled plates were solution treated at $980^{\circ}C$ for 1.5 h, quenched into water, cold rolled by 10% and 30% reduction in thickness, and then aged at $440{\sim}500^{\circ}C$ for 3, 4, 5 times. respectively. Cu-Ni-Si-P-x alloys cold rolled by 10 reduction before heat treatment have a good bendability compare to cold rolled by 30 reduction. Cu-3.4Ni-0.8Si-0.03P-0.1Ti shows the peak strength value of 759 MPa, an electrical conductivity of 39%IACS, an elongation of 10% and a hardness of 256 Hv aged at $440^{\circ}C$ for 6 hrs. Thus it is suitable for lead frame and connector.

• 통합자연과학논문집
• /
• 제2권4호
• /
• pp.233-236
• /
• 2009

This study was undertaken to measure the electrochemical corrosion of amorphous $Zr_{65}Al_8Ni_{15}Cu_{12}$ (at.%) alloy ribbon under various conditions, including 0.4 mM HCl solution, and for various values of the pH and the immersion time. The corrosion potentials($E_{corr}$) for the amorphous $Zr_{65}Al_8Ni_{15}Cu_{12}$ alloy in 0.4 mM HCl decreased with increasing temperature; the corrosion current density($I_{corr}$) increased with increasing temperature in general. The polarization resistance($R_p$) was inversely proportional to the corrosion rate. While pH=7, 9, 11 was not as sensitive as pH=3, 5, pH=3 was more sensitive for amorphous $Zr_{65}Al_8Ni_{15}Cu_{12}$ alloy than other pHs specially. The change of mass in the 70 mM $H_2SO_4$ solution with immersion time was the greatest in the first 100 h.

• 한국표면공학회지
• /
• 제54권6호
• /
• pp.315-323
• /
• 2021

In general, surface treatments of electroless Ni-P coating are extensively applied in the industry due to their excellent properties for considerable wear resistance, hardness, corrosion resistance. This study aims to determine the effect of ultrasonic conditions on the morphology, alumina content, roughness, hardness, and corrosion resistance of electroless Ni-P-Al₂O₃ composite coatings. The characteristics were analyzed by Energy-dispersive X-ray spectroscopy (EDX), x-ray diffractions (XRD), and atomic force microscopy (AFM), etc. In this study, the effect of ultrasonic condition uniformly distributed alumina within Ni-P solution resulting in a smoother surface, lower surface roughness. Furthermore, the corrosion resistance behavior of the coating was analyzed using tafel polarization curves in a 3.5 wt.% NaCl solution at 25 ℃. Under ultrasonic, Al₂O₃ content in Ni-P composite solution increased from 0.5 to 5.0 g/L, Al₂O₃ content at 3.0 g/L was showed a significantly enhanced corrosion resistance. These results suggested that ultrasonic condition was an effective method to improve the properties of the composite coating.

• 대한금속재료학회지
• /
• 제46권11호
• /
• pp.725-729
• /
• 2008

Deposition characteristics of electroless plated Ni-W-P films were investigated for various complexing agents. Used complexing agents are sodium citrate, sodium gluconate and sodium malonate. In this study, the existing mixed potential theory could explain the overall mechanism of Ni-W-P electroless plating for all complexing agents. The deposition rate could be also expected by the theory. The deposited Ni-W-P films were evaluated in term of surface hardness and corrosion resistance. Microhardness of the deposit increased about 1,000 Hv after heat treatment for one hour at $400^{\circ}C$, because it was above the crystallization temperature of $Ni_3P$. The deposited Ni-W-P films can exhibit excellent corrosion resistance in using sodium malonate as a complexing agent, the other hand the using sodium gluconate was the worst corrosion resistance. The worst corrosion resistance was due to a large number of nano-sized pin-holes or small pores. The plating current at the mixed potential increases when the using sodium malonate as a complexing agent, it was explained by the cross section.

• 한국결정성장학회지
• /
• 제25권5호
• /
• pp.193-198
• /
• 2015

본 연구에서는 전자파 차폐형 MCT(multi cable transit)의 인서트블록에 사용되는 유연성 EPDM(ethylene propylene diene monomer)고무 상에 무전해 도금을 이용하여 니켈도금을 실시하였다. 도금욕의 공정변수 조절 즉 pH 및 온도에 따라 Ni 도금층의 결정성 및 부착력이 결정되었다. pH와 온도를 달리하여 합성 한 결과 pH 7 및 8, $60{\sim}70^{\circ}C$에서 얻은 도금막들에서 잘 발달된 결정상과 높은 전기 전도도를 가짐을 알 수 있었다. pH 7, $70^{\circ}C$에서 도금 시 가장 높은 부착력 및 전기전도도를 얻을 수 있었으며, 또한 400 MHz~1 GHz 범위에서 우수한 전자파 차단능을 얻을 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.193.1-193.1
• /
• 2014

This study was to investigate the electronic structure and optical properties of Na doped into NiO thin film using XPS and REELS. The films were grown by electron beam evaporation with varying the annealing temperature. The relationship between the electrical characteristics with the local structure of NiO thin films was also discussed. The x-ray photoelectron results showed that the Ni 2p spectra for all films consist of Ni 2p3/2 which indicate the presence of Ni-O bond from NiO phase and for the annealed film at temperature above $200^{\circ}C$ shows the coexist Ni oxide and Ni metal phase. The reflection electron energy loss spectroscopy spectra showed that the band gaps of the NiO thin films were slightly decreased with Na-doped into films. The Na-doped NiO showed relatively low resistivity compared to the undoped NiO thin films. In addition, the Na-doped NiO thin films deposited at room temperature showed the best properties, such as a p-type semiconducting with low electrical resistivity of $11.57{\Omega}.cm$ and high optical transmittance of ~80% in the visible light region. These results indicate that the Na doping followed by annealing process plays a crucial in enhancing the electrical and optical properties of NiO thin films. We believe that our results can be a good guide for those growing NiO thin films with the purpose of device applications, which require deposited at room temperature.

• 한국지구과학회지
• /
• 제24권1호
• /
• pp.22-29
• /
• 2003

Temporal and spatial variability of precipitation (P), evaporation (E), and moisture balance (P-E; precipitation minus evaporation) has been investigated over the tropical ocean during the period from January 1998 to July 2001. Our data were analyzed by the EOF method using the satellite P and E observations made by the Tropical Rainfall Measuring Mission (TRMM) Precipitation Radar (PR) and the Special Sensor Microwave/Imager (SSM/I). This analysis has been performed for two three-year periods as follow; The first period which includes the El Ni${\tilde{n}}$o in early 1998 ranges from January 1998 to December 2000, and the second period which includes the La Ni${\tilde{n}}$o events in the early 1999 and 2000 (without El Ni${\tilde{n}}$o) ranges from August 1998 to July 2001. The areas of maxima and high variability in the precipitation and in the P-E were displaced from the tropical western Pacific and the ITCZ during the La Ni${\tilde{n}}$o to the tropical middle Pacific during the El Ni${\tilde{n}}$o, consistent with those in previous P studies. Their variations near the Korean Peninsula seem to exhibit a weakly positive correlation with that in the tropical Pacific during the El Ni${\tilde{n}}$o. The evaporation, out of phase with the precipitation, was reduced in the tropical western Pacific due to humid condition in boreal summer, but intensified in the Kuroshio and Gulf currents due to windy condition in winter. The P-E variability was determined mainly by the precipitation of which the variability was more localized but higher by 2-3 times than that of evaporation. Except for the ITCZ (0-10$^{\circ}$N), evaporation was found to dominate precipitation by ${\sim}$2 mm/day over the tropical Pacific. Annual and seasonal variations of P, E, and P-E were discussed.

• 마이크로전자및패키징학회지
• /
• 제19권1호
• /
• pp.55-60
• /
• 2012

고효율, 저가격의 태양전지를 위해 습식공정 중 하나인 Ni-P 무전해 도금을 이용한 실리콘 태양전지 웨이퍼를 열처리에 따른 4점굽힘시험을 통해 정량적인 계면 접착에너지를 평가하였다. 실험 결과 실리콘 태양전지 웨이퍼와 Ni-P 박막 사이의 계면접착에너지는 $14.83{\pm}0.76J/m^2$이며, 후속 열처리에 따른 실리콘 태양전지 웨이퍼와 Ni-P 무전해 도금은 $300^{\circ}C$ 처리 시 $12.33{\pm}1.16J/m^2$, $600^{\circ}C$ 처리 시 $10.83{\pm}0.42J/m^2$로써 전반적으로 높은 계면접착에너지를 가지나 열처리 온도가 증가할수록 계면접착에너지가 서서히 감소하였다. 4점굽힘시험 후 박리된 파면의 미세구조를 관찰 및 분석하여 내부의 파괴경로를 확인하였으며, X-선 광전자 분광법을 통하여 표면화학 결합상태를 분석한 결과 열처리 시 Ni-O와 Si-O 형태의 결합이 존재하여 약한 계면을 형성하기 때문인 것으로 판단된다.

• Composites Research
• /
• 제25권4호
• /
• pp.93-97
• /
• 2012

본 연구에서는 액상가압공정을 이용하여 탄소나노섬유(carbon nano fiber, CNF)를 강화재로 하는 AZ91 마그네슘 복합재를 제조하였다. CNF의 분산성 및 마그네슘 합금 용탕과의 젖음성을 향상시키고자 CNF를 마이크로 크기의 실리콘 카바이드 입자(silicon carbide particle, $SiC_p$)와 혼합하였다. 또한, CNF와 $SiC_p$의 혼합분말에 무전해도금법으로 니켈을 코팅하였다. 액상가압공정에서 AZ91 용탕은 무처리된 CNF, CNF와 $SiC_p$의 혼합분말(CNF+$SiC_p$), 니켈 코팅된 CNF와 $SiC_p$의 복합분말((CNF+$SiC_p$)/Ni)과 같이 세 종류의 강화재로 정수압에 의해 함침하여 복합재를 제조하였다. 무처리된 CNF 강화 복합재료에서는 일부 CNF 응집체가 관찰되었으나 CNF+$SiC_p$ 및 (CNF+$SiC_p$)/Ni 강화 복합재에서는 CNF가 기지재 내에 균일하게 분산되었음을 확인하였다. 압축시험결과, CNF+$SiC_p$ 및 (CNF+$SiC_p$)/Ni 강화 복합재의 압축강도가 무처리된 CNF 강화 복합재보다 각각 38%와 28% 향상되었다.