• Elastomers and Composites
• /
• 제57권2호
• /
• pp.48-54
• /
• 2022

A polymeric adhesion promoter was synthesized to improve the adhesive strength of the Ni lead frame/epoxy composite. Poly(itaconic acid-co-acrylamide) (IAcAAM) was prepared by copolymerizing itaconic acid and acrylamide. We compared the adhesive strength between the Ni lead frame and epoxy composite according to the molecular weight of IAcAAM. The molecular weight of IAcAAM was controlled using an initiator, which made it possible to use IAcAAM in the epoxy molding compound (EMC) manufacturing process by modulating the melting temperature. The adhesive strength of Ni lead frame/epoxy composite increased with the addition of IAcAAM to the epoxy composite. In addition, as the molecular weight of IAcAAM increased, the adhesive strength of the Ni lead frame/epoxy composite slightly increased. We confirmed that IAcAAM with an appropriate molecular weight can be used in the EMC manufacturing process and increase the adhesive strength of the Ni lead frame/epoxy composite.

• Journal of Welding and Joining
• /
• 제13권2호
• /
• pp.82-95
• /
• 1995

This paper discusses distribution of thermal stress, strain at near the joint and investigates the reliability of solder joints of electronic devices on a printed circuit board. As Electronic devices are composed of different materials, thermal stresses generate at near the interface, such as solder joints and interface between lC device and lead frame pad due to the differences of thermal expansion coefficients, As results of thermal stress, strain, micro crack often occurs thermal fatigue fracture at the interface of different materials, The initiation and propagation of micro crack depend on the environmental conditions, such as storage temperature and thermal cycling. Finally, this paper experimentally shows a way to suppress micro cracks by using Fe-Ni alloy clad lead frame, and investigates crack and thermal fatigue fracture of TSOP(Thin small outline package) type on printed circuit board.

• 소성∙가공
• /
• 제10권5호
• /
• pp.425-432
• /
• 2001

In order to investigate the influences of process parameters on the shape of lead frame, experimental study has been carried out. In the experiment, dimensional accuracy of the die sets, measurement accuracy has been managed carefully enough to simulate actual lead frame blanking process. With the blanking of square-shaped specimen, the effects of clearance, strip holding pressure and bridge width on the shape of blanked profile have been investigated. Experimental results show that the burnish ratio is increased as the clearance decreases. the strip holding pressure increases, and bridge width increases. Although the results seems to be similar to the ordinary blanking, the lead frame blanking shows a subtle different characteristics to the ordinary blanking due to the narrow bridge width.

• 한국자기학회지
• /
• 제11권2호
• /
• pp.50-57
• /
• 2001

강자성 극박소재에 유기된 잔류응력을 검출하기 위하여 자기유도형 탐촉자(probe)를 설계·제작하였으며, 이를 장착한 잔류음력 평가시스템은 박판내에 유기된 잔류응력의 주응력 방향과 크기를 효과적으로 결정하여 준다. 이 시스템을 반도체 칩 팩키지(package)용으로 사용하는 Fe-42Ni계 lead frame 판재의 잔류응력 검출에 적용한 결과, 양호재 및 잔류응력과다 불량재에 대한 출력전압은 명확히 구별되었고, 잔류응력이 축적된 판재는 양호재와 비교하여 응력의 분포 및 크기에 있어 항상 차이를 나타내었다. 이러한 차이는 탐촉자에 투입하는 전류와 주파수의 함수로 잘 분해되어질 수 있음을 확인하였다.

• 공업화학
• /
• 제27권1호
• /
• pp.21-25
• /
• 2016

리드프레임에 구리합금소재를 사용할 경우 구리이외의 고농도의 철, 니켈, 아연 등이 포함되며 여기서 발생되는 에칭폐액은 지정폐기물로 지정되어 있다. 따라서 본 연구에서는 전기도금용 산화구리(II)를 제조하기 위해 고농도 중금속을 함유한 리드프레임 에칭폐액의 맞춤형 정제과정을 설계하였다. 리드프레임 에칭폐액의 경우 중금속 함유량이 높아 이온교환수지법 단독으로는 중금속을 제거하는데 한계가 있었다. 따라서 본 연구에서는 물에 대한 용해도차를 이용한 환원-산화법을 연계하여 염화구리(I)을 제조한 후 산화제인 과황산나트륨을 이용하여 염화구리(II)로 재회수하는 방법을 사용하였다. 최적 환원제로는 하이드라진을 선택하였고, 최적 첨가량은 구리 1.0 mol당 1.4 mol이다. 환원-산화법과 이온교환수지법을 연결하여 중금속을 제거할 경우 3회 반복 시 $Fe^{3+}$ (4.3 ppm), $Ni^{2+}$ (2.4 ppm), $Zn^{2+}$ (0.78 ppm)로 전기도금용 산화구리(II) 제조용 원료로 사용이 가능할 것으로 사료된다.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.87-93
• /
• 2004

An experimental is carried out to investigate the characteristics of blanking for nickel alloy Alloy42 (t=0.203mm), a kind of IC lead frame material. By varying clearance between die and punch the shapes of shear profile are examined. Finite element analysis with element deletion algorithm for ductile fracture mode is also carried out to study the effect of clearance theoretically and to compare with experimental results. The rectangular shape specimen with four different comer radius is used to study the characteristics of blanking for straight side and comer region simultaneously. As the result the ratios measured k(m experiment of roll over, burnish and fracture zone based on initial blank thickness are compared with those of FE analysis. Both experiment and FE analysis show that the amount of mil over and fracture is increased as the clearance increases. When the radius of comer is less than thickness of blank it has been found that larger clearance is required than that of straight region in order to maintain same quality of shear profile at the comer region.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.658-662
• /
• 2000

The microstructure, adhesion strength and conductivity of electroplated Sn-Cu Films on Alloy42 lead Frame were measured for comparison. In the case of electroplated 90Sn10Cu, 99Sn1Cu, Cu$\sub$10/Sn$_3$Phase was formed and Ni$_3$Sn$_2$Phase was formed after 200$^{\circ}C$, 30min annealing. In the case of electroplated 99Sn1Cu, Cu$\sub$10/Sn, Ni$_3$Sn phases were formed and Ni$_3$Sn$_4$, Ni$_3$Sn$_4$phases were formed after 200$^{\circ}C$, 30min annealing. 90Sn10Cu film was measured better uniformity, adhesion strength and conductivity than 99Sn1Cu.

• 한국재료학회지
• /
• 제34권3호
• /
• pp.170-174
• /
• 2024

In this study, we report the microstructural evolution and shear strength of an Sn-Sb alloy, used for die attach process as a solder layer of backside metal (BSM). The Sb content in the binary system was less than 1 at%. A chip with the Sn-Sb BSM was attached to a Ag plated Cu lead frame. The microstructure evolution was investigated after die bonding at 330 ℃, die bonding and isothermal heat treatment at 330 ℃ for 5 min and wire bonding at 260 ℃, respectively. At the interface between the chip and lead frame, Ni₃Sn₄ and Ag₃Sn intermetallic compounds (IMCs) layers and pure Sn regions were confirmed after die bonding. When the isothermal heat treatment is conducted, pure Sn regions disappear at the interface because the Sn is consumed to form Ni₃Sn₄ and Ag₃Sn IMCs. After the wire bonding process, the interface is composed of Ni₃Sn₄, Ag₃Sn and (Ag,Cu)₃Sn IMCs. The Sn-Sb BSM had a high maximum shear strength of 78.2 MPa, which is higher than the required specification of 6.2 MPa. In addition, it showed good wetting flow.

• 열처리공학회지
• /
• 제26권5호
• /
• pp.225-232
• /
• 2013

The influence of aging treatment, addition elements and rolling reduction ratio on the microstructure, mechanical, electrical and bendability properties of Cu-Ni-Si-P-x (x = Fe, Sn, Zn) alloys for connector material application was investigated. SEM/EDS analysis exhibited that Ni2-Si precipitates with a size of 20~100 nm were distributed in grains. Fe, Sn, Zn elemnets in Cu-Ni-Si-P alloy imporved the mechanical strength but it was not favor in increasing of electrical conductivity. As higher final rolling reduction ratio, the strength and electrical conductivity is increased after aging treatment, but it indicated excellent bendability. Especially, Cu-2Ni-0.4Si-0.5Sn-0.1Fe-0.03P alloy show the tensile strength value of 700MPa and the electrical conductivity was observed to reach a maximum of 40%IACS. It is optimal for lead frame and connector.

• 열처리공학회지
• /
• 제27권1호
• /
• pp.1-9
• /
• 2014

For connector material applications, the influence alloying elements of Mn, Cr, Fe, and Ti and cold rolling reduction on the mechanical property, electrical conductivity and bendiability of Cu-Ni-Si-P alloy was investigated. The hot rolled plates were solution treated at $980^{\circ}C$ for 1.5 h, quenched into water, cold rolled by 10% and 30% reduction in thickness, and then aged at $440{\sim}500^{\circ}C$ for 3, 4, 5 times. respectively. Cu-Ni-Si-P-x alloys cold rolled by 10 reduction before heat treatment have a good bendability compare to cold rolled by 30 reduction. Cu-3.4Ni-0.8Si-0.03P-0.1Ti shows the peak strength value of 759 MPa, an electrical conductivity of 39%IACS, an elongation of 10% and a hardness of 256 Hv aged at $440^{\circ}C$ for 6 hrs. Thus it is suitable for lead frame and connector.