• Journal of Magnetics
• /
• 제8권4호
• /
• pp.133-137
• /
• 2003

The magnetostatic properties of the as-deposited and annealed at T=300 and 400$^{\circ}C$ Ni films were investigated employing both magneto-optical magnetometer and VSM. The Ni films of 50∼200 nm thicknesses were prepared by DC magnetron sputtering technique. The strong influence of annealing temperature on magnetostatic properties of the studied samples was discovered. For the annealed Ni films, the increase of the coercivity H$_c$ (up to 4 times) in comparison with that of as-deposited samples was revealed. The obtained results were explained by using crystallographic structural data of the samples.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.658-662
• /
• 2000

The microstructure, adhesion strength and conductivity of electroplated Sn-Cu Films on Alloy42 lead Frame were measured for comparison. In the case of electroplated 90Sn10Cu, 99Sn1Cu, Cu$\sub$10/Sn$_3$Phase was formed and Ni$_3$Sn$_2$Phase was formed after 200$^{\circ}C$, 30min annealing. In the case of electroplated 99Sn1Cu, Cu$\sub$10/Sn, Ni$_3$Sn phases were formed and Ni$_3$Sn$_4$, Ni$_3$Sn$_4$phases were formed after 200$^{\circ}C$, 30min annealing. 90Sn10Cu film was measured better uniformity, adhesion strength and conductivity than 99Sn1Cu.

• 한국전기전자재료학회논문지
• /
• 제16권2호
• /
• pp.97-101
• /
• 2003

New Pt/Ti and hi/Ti double-metal structures have been investigated for the application of a diffusion barrier between Cu and Si in deep submicron integrated circuits. Pt/Ti and Ni/Ti were deposited using E-beam evaporator at room temperature. The performance of Pt/Ti and Ni/Ti structures as diffusion barrier against Cu diffusion was examined by charge pumping method, gate leakage current, junction leakage current, and SIMS(secondary ion mass spectroscopy). These evaluation indicated that Pt/Ti(200${\AA}$/100${\AA}$) film is a good barrier against Cu diffusion up to 450$^{\circ}C$.

• 한국표면공학회지
• /
• 제37권5호
• /
• pp.263-272
• /
• 2004

High strength steels such as transformation induced plastic steel, dual phase and solid solution Hardening have been developed and continuously improved due to the intensified needs in the automotive industry. But silicon and manganese in transformation induced plastic steels were known to exhibit harmful effects on galvannealing reaction by oxide film formed during heat treatment. Therefore, in this work, the applicability of Zn-Ni electrodeposition instead of hot dip galvannealed coating to transformation induced plastic steels was evaluated and optimum electroplating condition was investigated. Based on these investigations optimized electroplating conditions were proposed and Zn-Ni electrogalvanized steel sheet was produced by EGL (electrogalvanized line). Its perfomance properties for automotive steel was evaluated.

• 센서학회지
• /
• 제30권2호
• /
• pp.71-75
• /
• 2021

Recently, transition-metal-based hydroxide materials have attracted significant attention in various electrochemical applications owing to their low cost, high stability, and versatility in composition and morphology. Among these applications, transition-metal-based hydroxides have exhibited significant potential in supercapacitors owing to their multiple redox states that can considerably enhance the supercapacitance performance. In this study, nanostructured Ni-Mn double hydroxide is directly grown on a conductive substrate using an electrodeposition method. Ni-Mn double hydroxide exhibits excellent electrochemical charge-storage properties in a 1 M KOH electrolyte, such as a specific capacitance of 1364 Fg-1 at a current density of 1 mAcm-2 and a capacitance retention of 94% over 3000 charge-discharge cycles at a current density of 10 mAcm-2. The present work demonstrates a scalable, time-saving, and cost-effective approach for the preparation of Ni-Mn double hydroxide with potential application in high-charge-storage kinetics, which can also be extended for other transition-metal-based double hydroxides.

• 한국세라믹학회지
• /
• 제13권2호
• /
• pp.8-16
• /
• 1976

The conductive transparent film is prepared by spraying thin salt solution. In stannic chloride solution as a base solution, various dopants such as Al, Co, Cu and Ni were dissolved respectively as a chloride state and then the films were made by spraying solutions on hot glass plates. The properties of them were compared with those of the stannic salt single component film. The films doped with copper oxide and nickle oxide were improved by decreasing their sheet resistivity and temperature coefficient of resistivity. In comparison with the sheet resistivity and temperature coefficient of resistivity of stannic oxide single component film, being 2.5 K ohm/$\textrm{cm}^2$ and -1650ppm/$^{\circ}C$ respectively, its values of the film containing 15 mol % of copper oxide and formed at 40$0^{\circ}C$ were 2.5K ohm/$\textrm{cm}^2$ and -920ppm/$^{\circ}C$ respectively. The film containing 15 mol % of nickel oxide and formed at 50$0^{\circ}C$ has shown its sheet resistivity and temperature coefficient 0.7 K ohm/$\textrm{cm}^2$ and -940ppm/$^{\circ}C$ respectively.

• 한국재료학회지
• /
• 제14권5호
• /
• pp.343-347
• /
• 2004

We investigated the growth feasibility of polycrystalline Si film on mica substrate for the transfer of the layer to a plastic substrate. The annealing temperature was limited up to $600^{\circ}C$ because of crack development in the mica substrate. Amorphous Si film was deposited on mica substrate by PECVD and was crystallized by furnace annealing. During the annealing, bubbles were formed at the Si/mica interface. The bubble formation was avoided by the Ar-plasma treatment before amorphous Si deposition. A uniform and clean polycrystalline Si film was obtained by coating $NiCl_2$ on the amorphous Si film and annealing at $500^{\circ}C$ for 10 h. The conventional Si lithography was possible on the mica substrate and the devices fabricated on the substrate could be transferred to a plastic substrate.

• 한국재료학회지
• /
• 제7권1호
• /
• pp.69-75
• /
• 1997

$SiO_{2}/CoNiCr/Cr$ 합금 박막을 RF magnetron sputtering 법으로 Cr의 두께를 변화시키면서 제조하였다. 제조된 박막을 진공 열처리하여 열처리 온도에 따른 포화자화, 보자력, 각형비를 조사하였다. $SiO_{2}/CoNiCr/Cr$ 합금 박막에서 포화자화 값은 Cr 하지층의 두께가 증가함에 따라 감소하고 보자력은Cr 하지층의 두께가 증가함에 따라 증가하였다. 이러한 박막의 포화자화 값은 600 emu/cc, 최대 보자력은 550 Oe를 나타내었다. $SiO_{2}/CoNiCr/Cr(1700{\AA})$ 합금 박막에서는 열처리 온도가 증가함에 따라 포화자화 값은 급격히 감소하고 보자력은 증가하였다. 열처리 온도가 $650^{\circ}C$에서 포화자화 값은 as-deposited상태보다도 1/10로 감소하였고 보자력은 1600 Oe로 최대값ㅇ르 나타내었다. Cr 하지층의 두께와 열처리 온도의 증가에 따른 포화자화의 감소는 하지층에서 자성층으로 Cr이 확산하므로써 자기 모멘트의 감소에 의한 것으로 판단된다. 또한 보자력의 증가는 박막 면에 수직한 방향으로 급격한 결정 성장에 기인한 것이다.

• 한국자기학회지
• /
• 제7권5호
• /
• pp.265-273
• /
• 1997

연자성 자유자성층과 피속박자성층을 각각 2중층 Ni$_{81}$fe$_{19}$/ $Co_{90}$ Fe$_{10}$와 $Co_{90}$ Fe$_{10}$로 하고, 반강자성 속박층을 NiO로 하는 NiFe/CoFe/Cu/CuFe/NiO 구조를 갖는 spin-valve 박막을 sputtering 방법으로 유리기판위에 제작하고, 자기저항비(MR), 자기장감응도(field sensitivity), 반강자성층과 피속박자성층사이의 교환결합 자기장(exchange coupling field), 자유자성층과 피속박자성층사이의 층간결합자기장(interlayer coupling field) 등의 비자성 사이층 Cu 두께, 자유자성층두께, 피속박자성층 두께 및 반강자성층 두께 의존성을 조사하였다. 2중층 자유자성층에 연자성 NiFe가 20 .angs. 이상 포함됨으로써 10 Oe의 보자력을 가져 연자성특성을 향상시키는 것을 확인할 수 있었다. Cu의 두께가 30 .angs. 일 때 극대 MR비를 가졌으며 두께증가에 따라 감소하는 경향을 보였다. 피속박자성층 CoFe의 두께가 35 .angs. 일 때 그대 MR비 6.3%를 나타내며 두께증가에 따라 감소하며 교환결합자기장도 CoFe 두께가 증가함에 따라 감소하였다. NiO 두께가 800 .angs. 일 때 극대 MR비를 보이며 교환결합자기장은 두께증가에 따라 50 Oe 정도로 포화되어 NiO가 반강자성 특성을 유지하기 위해서는 일정한 두께이상이 되어야 함을 알 수 있었다. 열처리온도 200 .deg. C 까지는 MR비 5.3%를 유지하다 이보다 높하지면 점점 감소하여 300 .deg. C에서도 약 3% 정도를 유지하여 열적 안정성이 향상되었다. 따라서 CoFe 합금을 사용하여 NiFe(40 .angs. )/CoFe(50 .angs. )/Cu(30 .angs. )/CoFe(35 .angs. )/NiO(800 .angs. ) 구조를 갖는 spin-valve 박막은 극대 MR비 6.3%, 유효자기장감응도 약 0.5(%/Oe)를 보여 spin-valve head 재료로 적합함을 알 수 있었다.다.다.다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1994년도 추계 학술발표 강연 및 논문 개요집
• /
• pp.4-4
• /
• 1994