• Journal of Welding and Joining
• /
• 제11권4호
• /
• pp.91-102
• /
• 1993

The plasma sprayed $Cr_3C_2$-NiCr coatings are widely used as wear-resistant and corrosion-resistant materials. The mechanical and wear properties of the plasma sprayed $Cr_3C_2$-NiCr coating on steel plate were examined in this study. The pore in the coatings could be classified into two types, the one is the intrinsic pore originated from the spraying powder, the other is the extrinsic pore formed during spraying. During the tensile adhesion test, the fracture occured at the interface of top coating and bond coating. It is though that the compressive residual stress increases with the increase of the top coating thickness. From the wear test, it was found that the wear rate increased with the increase of the sliding velocity regardless of the temperature. It is thought that the fracture toughness reduces with the increase of the sliding velocity at $30^{\circ}C$ and that the adhesion amount increases with the increase of the sliding velocity at $400^{\circ}C$ It is concluded that the wear mechanism at $30^{\circ}C$ is the fracture and pull-out of the carbide particles due to the fatigue on sliding surface, while the wear mechanism at $400^{\circ}C$ is the adhesion of the smeared layer formed during wear process.

• 한국생산제조학회지
• /
• 제20권2호
• /
• pp.187-192
• /
• 2011

UBM(Under Bump Metallurgy) is very important for successful realization of Flip-Chip technology. In this study, it is investigated the interfacial reactions between various Sn-Ag solder alloys and Ni-P/Au UBM and Cu plate finish. It is also evaluated the shear strength by using the micro shear-punch test method for Sn-37Pb alloy, binary and ternary alloys of environment-friendly Pb-free solder alloys which are applied in the electronic packages. In terms of interfacial microstructure, the Pb-free solder joints have thicker IMCs than the Sn-Pb solder joints. The thickness of IMC is related to Reflow time. The IMC has been observed to grow with the increase in Reflow time. As a result of the shear test, in case of Max. shear strength, Pb-free solder showed the highest strength value and Sn-37Pb showed the lowest strength value 10 be generally condition of Reflow time.

• 한국생산제조학회지
• /
• 제25권5호
• /
• pp.329-337
• /
• 2016

The demand for the eco-friendly vehicles is skyrocketing because of the increasing $CO_2$ emissions and global warming. In the industrial field, the battery process, a core part of an eco-friendly vehicle, is drawing increased attention; its weight lightening as well as high energy density are becoming increasingly important. In this study, pure Ni plates that were used as the battery pole plate were welded using the laser. The lab joint welding was conducted on ten pure Ni plates at a laser power of 1900 W and a feed speed of 2.8-3.4 m/min. As observed in the experiment, a faster feed speed reduced the bead width, but the laser did not penetrate all ten specimen plates. In addition, pores were trapped when protective gas was used, but they were not trapped when the welding was conducted in atmospheric condition.

• 한국분말재료학회지
• /
• 제22권6호
• /
• pp.432-437
• /
• 2015

The en-riched $^{58}Ni$ powders are dissolved in acid solution and coated on a Cu target for proton irradiation at cyclotron to produce $^{57}Co$ radioisotope. The condition of the plating bath and the coating process are determined using the en-riched powders. To establish the coating conditions for $^{57}Co$, non-radioactive Co ions are dissolved in an acid solution and electroplated on to a rhodium plate. The thermal diffusion of electroplated Co into a rhodium matrix was studied to apply a $^{57}Co$ Mssbauer source. The diffusion depth from surface to matrix of Co is depended on the annealing temperature and time. The deposited Co atoms diffuse completely into a rhodium (Rh) matrix without substantial loss at an annealing temperature of 1200 for 4 hours.

• 공업화학
• /
• 제7권4호
• /
• pp.614-622
• /
• 1996

엣칭용 염화제2철 용액중의 효과적인 니켈제거에 관해 연구하였다. 전해철괴 또는 폐새도우마스크 철편을 사용하여 염화제2철을 염화제1철로 환원시킨후 용액중의 $Ni^{2+}$를 전해철 분말로 환원 석출시켰다. 최적의 실험조건하에서 초기 니켈의 농도가 1.0%일 때 니켈제거율은 99%이었고 초기 니켈의 농도가 0.1%일 때 니켈제거율은 98%이었다. 염화제2철의 환원반응 중에 생성된 수산화철의 종류 및 입자크기를 XRD와 SEM으로 분석하였다.

• 대한기계학회논문집A
• /
• 제39권7호
• /
• pp.681-686
• /
• 2015

본 연구는 steel 재질의 판과 Cu, Ni, Al, Mg 재질의 핀 간에 발생하는 마찰에 의한 마찰소음 특성을 왕복운동 및 회전운동 실험장치를 통하여 연구하였다. 실험 결과 미끄럼 속도에 대한 마찰곡선의 음의 기울기가 소음발생시점에 영향을 주었다. 특히 Cu 가 소음발생시점과 음의 기울기 측면에서 마찰소음방지에 가장 우수한 재질임을 확인하였다.

• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.41-47
• /
• 1996

The spot weldability of coated steels for automobile has been investigated. Coated steels of SPC-Zn DC, SPC Zn-Ni SC, SPC Zn-Ni DC, SPC Zn-Fe DC and OCCS were welded under different conditions of welding current, force and time. Coating thickness at the welded surface was reduced as increased welding current. Tensile shear strength(TSS) and cross tensile strength (CTS) were increased up to expulsion began, then dropped as increased current. Optimum conditions of welding force and time were different, however 200~250kgf and 15~20cycle were optimum for coated SPC (Steel Plate Cold). Weldability lobes were measured for each coated steel and they showed narrow range of working welding current. The organic composite coated steel (OCCS) had the highest current to get $\sqrt5{t}$ nugget size and narrowest working welding current range.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• 제10권S_3호
• /
• pp.139-148
• /
• 2001

Heavy metals such as Cu, Ni, Cd, and Pb were chemically extract from the contaminated soils using the chelating agents, EDTA and DTPA. These chemical extraction have been focused on its applicability to a wide range of soils. Results of extractive efficiency for heavy metal follow the order : Cu-EDTA $\geq$ Ni-EDTA > Pb-EDTA > Cd-EDTA > Cu-DTPA> Pb-DTPA. This result is coincided with order of conditional formation constants(Kr) of metal-chelate agent. The second study involved the recovery of the metals and EDTA from complex solutions by an electromembrane process. The overall processes of regeneration, recovery, and reuse were evaluated. The electrochemical studies showed that copper could be chosen as an electrode to plate Cd, Cu, and Pb. At least 95% of 75 of EDTA and associated Cu or Pb could be recovered by the electromembrane process. Recovery of Cd by electodeposition was not possible with the copper electrode. The percent EDTA recovery is equal to the percentage of metal electroplated from the chelates.

• 한국가스학회지
• /
• 제8권3호
• /
• pp.57-62
• /
• 2004

본 연구는 천연가스 생산기지를 구성하는 설비 가운데 핵심설비라 할 수 있는 LNG 저장탱크의 설계 기술을, 세계에서 다섯 번째로 국내 기술로 설계를 완료하여 건설 중에 있는, OO 생산기지 LNG 저장탱크(용량 ; 14만kl, 형식 : 지상식, $9\%$ Ni강 내조 $\cdot$ Prestressed Concrete 외조) 1기에 대한 공정설비의 설계 적합성과 탱크 외벽에 대한 소화설비의 설계 적합성에 관하여 연구하였다.

• 공업화학
• /
• 제8권5호
• /
• pp.742-748
• /
• 1997

초경공구(WC-Co)의 성능 향상을 목적으로 고경도, 높은 열전도도의 특성 등을 가진 다이아몬드 막을 코팅하고 있으나 WC-Co 기판표면의 특성상 문제점으로 인하여 코팅의 어려움이 있다. 이 문제의 해결을 위하여 WC-Co기판위에 중간층을 도입한 후 다이아몬드 막을 증착시키는 새로운 방법을 고려하였으며 중간층의 제조에 무전해 Ni-P도금법을 사용하였다. 무전해도금을 위한 WC-Co기판의 전처리, 무전해도금 및 열처리, 다이아몬드 막 증착의 공정에 대하여 조사하였다. 형성되는 계면의 구조와 성분, 계면간의 밀착력 등을 Scratch Tester, Roughness Tester, SEM/EDS, XRD, Raman Spectroscopy를 사용하여 분석하였다. 무전해도금의 전처리로서 산에 의한 방법과 다이아몬드 분말에 의한 방법을 사용하였으며 두 경우에 모두 WC-Co기판의 표면조도의 감소, 표면 Co성분의 감소, 그리고 밀착력 저하가 관찰되었다. 무전해도금층의 열처리시 영향을 조사하였으며 온도 증가에 따라 Ni 결정이 형성되며 이로 인하여 도금의 밀착력이 증가되며 Ni 결정이 성장함을 관찰하였다. 또한 열처리된 Ni-P도금 위에서 다이아몬드막 증착 실험을 실시하였으며 증착온도를 증가시킴에 따라 다이아몬드 형성이 증가되어 $800^{\circ}C$일때 양호한 다이아몬드 막을 얻을 수 있었다. 본 연구의 방법 및 실험조건은 WC-Co를 비롯하여 다이아몬드 막 형성이 어려운 소재들의 코팅에 효과적으로 이용될 수 있다.