• Korean Journal of Metals and Materials
• /
• v.49 no.10
• /
• pp.811-817
• /
• 2011

In this study, we have investigated the role of a metal oxide hole injection layer (HIL) between an Indium Tin Oxide (ITO) electrode and an organic hole transporting layer (HTL) in organic light emitting diodes (OLEDs). Nickel Oxide films were deposited at different deposition times of 0 to 60 seconds, thus leading to a thickness from 0 to 15 nm on ITO/glass substrates. To study the influence of NiO film thickness on the properties of OLEDs, the relationships between NiO/ITO morphology and surface properties have been studied by UV-visible spectroscopy measurements and AFM microscopy. The dependences of the I-V-L properties on the thickness of the NiO layers were examined. Comparing these with devices without an NiO buffer layer, turn-on voltage and luminance have been obviously improved by using the NiO buffer layer with a thickness smaller than 10 nm in OLEDs. Moreover, the efficiency of the device ITO/NiO (< 5 nm)/NPB/$Alq_3$/ LiF/Al has increased two times at the same operation voltage (8V). Insertion of a thin NiO layer between the ITO and HTL enhances the hole injection, which can increase the device efficiency and decrease the turn-on voltage, while also decreasing the interface roughness.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.237-245
• /
• 2021

Atomic layer deposition (ALD) enhances the stability of cathode materials via surface modification. Previous studies have demonstrated that an Ni-rich cathode, such as LiNi_0.8Co_0.1Mn_0.1O₂, is a promising candidate owing to its high capacity, but is limited by poor cycle stability. In this study, to enhance the stability of the Ni-rich cathode, synthesized LiNi_0.8Co_0.1Mn_0.1O₂ was coated with Al₂O₃ using ALD. Thus, the surface-modified cathode exhibited enhanced stability by protecting the interface from Ni-O formation during the cycling process. The coated LiNi_0.8Co_0.1Mn_0.1O₂ exhibited a capacity of 176 mAh g^-1 at 1 C and retained up to 72% of the initial capacity after 100 cycles within a range of 2.8-4.3 V (vs Li/Li⁺. In contrast, pristine LiNi_0.8Co_0.1Mn_0.1O₂ presented only 58% of capacity retention after 100 cycles with an initial capacity of 173 mAh g^-1. Improved cyclability may be a result of the ALD coating, which physically protects the electrode by modifying the interface, and prevents degradation by resisting side reactions that result in capacity decay. The electrochemical impedance spectra and structural and morphological analysis performed using electron microscopy and X-ray techniques establish the surface enhancement resulting from the aforementioned strategy.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.84.1-84.1
• /
• 2010

Since the discovery of the carbon nanotube(CNTs), they have attracted much attention because of unique properties that may impact many fields of science and technology. The considerable properties of CNTs include high surface area, outstanding thermal, electrical conductivity and mechanical stability. However, uniform deposition of Pt nanoparticles on carbon surface remains inaccessible territory because of the inert carbon surface. In this study, we prepared directly oriented CNTs on carbon paper as a catalyst support in cathode electrode. carbon surface was functionalized using aryl diazonium salt for increasing adhesion of Ni particles which is precursor for growing CNTs. For fabricate electrode, CNTs on carbon paper were grown by chemical vapor deposition using Ni catalyst and Pt nanoparticles were deposited on CNTs oriented carbon paper by polyol method. The performance was measured using Proton electrolyte Membrane Fuel Cell(PEMFC). The structure and morphology of the Pt nanoparticles on CNTs were characterized by Scanning electron Microscopy(SEM) and Transmission electron Microscopy (TEM). The average diameter of Pt nanoparticles was 3nm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12
• /
• pp.1080-1086
• /
• 2003

Effects of E$_2$O$_3$. HO$_2$O$_3$ and Dy$_2$O$_3$ addition on dielectric properties of non-reducible BaTiO$_3$ based X7R dielectrics with Ni electrode have been studied in a reduced atmosphere. As the content of rare-earth with E$_2$O$_3$. HO$_2$O$_3$, Dy$_2$O$_3$ was less than 3wt%, The TCC(Temperature Capacitance Change) and insulation resistance characteristics were improved by compensate the oxygen vacancies due to occupy either the Ba or Ti site. We developed the composition of X7R (EIA standard) for higher capacitance MLCC which had high reliability electric properties by the addition of Er ion into BaTiO$_3$ + MgO + Y2O$_3$ + MnO + (Ba$\sub$0.4/Ca$\sub$0.6/)SiO$_3$ composition.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.8
• /
• pp.1733-1737
• /
• 2009

A new cathode material based on Li$Ni_{0.8}Co_{0.15}Al_{0.05}O_2$ (LNCA)/polyaniline (Pani) composite was prepared by in situ self-stabilized dispersion polymerization in the presence of LNCA. The materials were characterized by fourier transform infrared spectroscopy (FT-IR), ultraviolet-visible spectroscopy (UV-Vis), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Electrochemical properties including galvanostatic charge-discharge ability, cyclic voltammetry (CV), capacity, cycling performance, and AC impedance were measured. The synthesized LNCA/Pani had a similar particle size to LNCA and exhibited good electrochemical properties at a high C rate. Pani (the emeraldine salt form) interacts with metal-oxide particles to generate good connectivity. This material shows good reversibility for Li insertion in discharge cycles when used as the electrode of lithium ion batteries. Therefore, the Pani coating is beneficial for stabilizing the structure and reducing the resistance of the LNCA. In particular, the LNCA/Pani material has advantageous electrochemical properties.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.1
• /
• pp.53-60
• /
• 2017

Fluoroethylene carbonate (FEC) was studied as an additive for the electrolyte in lithium ion batteries with the $LiNi_{0.5}Mn_{1.5}O_4$ (LNMO) spinel cathode operating at a high potential beyond 4.7 V (vs. $Li/Li^+$). It was found that the FEC additive was electrochemically active for the $1^{st}$ charge cycle on the LNMO cathode. The presence of a large amount of FEC (more than 40 vol%) in the electrolyte caused severe side reactions with abnormally long voltage plateaus. In contrast, when the electrolyte contained less than 30 vol% FEC, the surface of the LNMO cathode was stabilized by the formation of the solid-electrolyte interphase (SEI), leading to improved cyclability. However, the resistance from the SEI limited the rate capability because of sluggish lithium transportation through the SEI and electronic insulation between the particles in the electrode.

• Journal of the Korean Chemical Society
• /
• v.57 no.3
• /
• pp.316-321
• /
• 2013

Electrocoagulation (EC) technique is applied for the treatment of wastewater containing heavy metals ions such as nickle (Ni), lead (Pb) and cadmium (Cd) by using sacrificial anodes corrode to release active coagulant flocs usually aluminium or iron cations into the solution. During electrolytic reactions hydrogen gas evolve at the cathode. All the experiments were carried out in Batch mode. The tank was filled with synthetic wastewater containing heavy metals and efficiency of electro-coagulation in combination with aluminum and iron electrodes were investigated for removal of such metals. Several parameters, such as contact time, pH, electro-coagulant concentration, and current density were optimized to achieve maximum removal efficiency (%). The concentrations of heavy metals were determined by using Atomic Absorption Spectroscopy (AAS). It is found that the electro-coagulation process has potential to be utilized for the cost-effective removal of heavy metals from wastewater specially using iron electrodes in terms of high removal efficiencies and operating cost.

• Journal of Ceramic Processing Research
• /
• v.19 no.5
• /
• pp.413-418
• /
• 2018

All-solid-state lithium batteries (ASSBs) using inorganic sulfide-based solid electrolytes are considered prospective alternatives to existing liquid electrolyte-based batteries owing to benefits such as non-flammability. However, it is difficult to form a favorable solid-solid interface among electrode constituents because all the constituents are solid particles. It is important to form an effective electron conduction network in composite cathode while increasing utilization of active materials and not blocking the lithium ion path, resulting in excellent cell performance. In this study, a mixture of fibrous VGCF and spherical nano-sized Super P was used to improve rate performance by fabricating valid conduction paths in composite cathodes. Then, composite cathodes of ASSBs containing 70% and 80% active materials ($LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$) were prepared by a solution-based process to achieve uniform dispersion of the electrode components in the slurry. We investigated the influence of binary carbon additives in the cathode of all-solid-state batteries to improve rate performance by constructing an effective electron conduction network.

• Applied Chemistry for Engineering
• /
• v.5 no.1
• /
• pp.81-89
• /
• 1994

A study on Mm type electrode which is relatively high in electrode capacity and low in material cost was performed to develope high performance nickel-metal hydride battery. The electrode characteristics were investigated by P-C-T, charge-discharge and microencapsulation treatment experiments. The plateau pressure and hydrogen absorption capacity obtained from the P-C-T experiment were 0.4 atm and 310 mAh/g, respectively. The electrode capacity and stability of microencapsulated electrode were improved than those of conductor mixed electrode and the microencapsulation was possible without pretreatment. The electrode capacity of microencapsulated Mm type alloy was 240~250 mAh/g(0.2 C).

• Korean Journal of Materials Research
• /
• v.26 no.11
• /
• pp.649-655
• /
• 2016

Ni nanoparticles (NPs)-graphitic carbon nanofiber (GCNF) composites were fabricated using an electrospinning method. The amounts of Ni precursor used as catalyst for the catalytic graphitization were controlled at 0, 2, 5, and 8 wt% to improve the photovoltaic performances of the nanoparticles and make them suitable for use as counter electrodes for dye-sensitized solar cells (DSSCs). As a result, Ni NPs-GCNF composites that were fabricated with 8 wt% Ni precursors showed a high circuit voltage (0.73 V), high photocurrent density ($14.26mA/cm^2$), and superb power-conversion efficiency (6.72%) when compared to those characteristics of other samples. These performance improvements can be attributed to the reduced charge transport resistance that results from the synergetic effect of the superior catalytic activity of Ni NPs and the efficient charge transfer due to the formation of GCNF with high electrical conductivity. Thus, Ni NPs-GCNF composites may be used as promising counter electrodes in DSSCs.