• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.8 s.113
• /
• pp.848-856
• /
• 2006

This paper describes the aeroelastic stability test of the small-scaled 'Next-generation Blade(NRSB)' with NRSH (next-generation hub system) and HCTH hingeless hub system in hover and forward flight conditions. Excitation tests of rotor system installed in GSRTS (general small-scale rotor test system) at KARI (Korea Aerospace Research Institute) were carried out to get lead-lag damping ratio of blades with flexures as hub flexure. MBA(moving block analysis) technique was used for the estimation of lead-lag damping ratio. First, NRSB-1F blades with HCTH hub system, then NRSB- 1F with NRSH hub system were tested. Second, NRSB-2F blades with NRSH hub system were tested. Tests were done on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively. Non-rotating natural frequencies, non-rotating damping ratios and rotating natural frequencies were showed similar level for each cases. Estimated damping ratios of NRSB-1F, NRSB-2F with HCTH and NRSH were above 0.5%, and damping ratio increased by collective pitch angle increasement. Furthermore damping ratios of NRSB-2F were higher than damping ratios of NRSB-1F in high Pitch angle. It was confirmed that the blade design for noise reduction would give observable improvement in aeroelastic stability compared to paddle blade and NRSB-1F design.

• Journal of the Korea Society of Computer and Information
• /
• v.27 no.7
• /
• pp.57-64
• /
• 2022

In this paper, the definition and overview of digital health care that has emerged recently, core technology, and We would like to propose a plan to establish a next-generation information protection system that can protect digital healthcare devices and data from cyber attacks. Various vulnerabilities exist for digital healthcare devices and data, and cyber attacks are possible for those vulnerabilities. Through an attack on digital health care devices and information and communication networks, it can directly adversely affect human life and health, Since digital healthcare data contains sensitive and personal information, it is essential to safely protect it from cyber attacks. In the case of this proposal, for continuous safe management of data and cyber attacks on equipment and communication networks for digital health devices, It is expected to be able to respond more effectively and continuously through the establishment of the next-generation information protection system.

• Journal of the Korean Chemical Society
• /
• v.67 no.1
• /
• pp.19-27
• /
• 2023

During the past few decades, toxicity science is shifting from observative to predictive science. New approach methodologies (NAMs), including in chemico, in silico, in vitro approach, gain attention to reduce, refine, replace the whole animal toxicity testing. However, actual acceptances of NAMs in regulatory decision-making have been limited due to low confidence. To address the current constraints, Accelerating the Pace of Chemical Risk Assessment (APCRA) initiative conducted several case studies and presented the perspectives of next generation risk assessment (NGRA). In this review, we suggested a concept and perspectives of NGRA through analysis on APCRA case studies.

• Journal of Electrochemical Science and Technology
• /
• v.14 no.2
• /
• pp.184-193
• /
• 2023

This study investigates the effects of a carbon fiber layer formed on the surface of an etched aluminum current collector on the electrochemical properties of the activated carbon electrodes for an electric double layer capacitor. A particle size analyzer, field-emission SEM, and nitrogen adsorption/desorption isotherm analyzer are employed to analyze the structure of the carbon fiber layer. The electric and electrochemical properties of the activated carbon electrodes using a carbon fiber layer are evaluated using an electrode resistance meter and a charge-discharge tester, respectively. To uniformly coat the surface with carbon fiber, we applied a planetary mill process, adjusted the particle size, and prepared the carbon paste by dispersing in a binder. Subsequently, the carbon paste was coated on the surface of the etched aluminum current collector to form the carbon under layer, after which an activated carbon slurry was coated to form the electrodes. Based on the results, the interface resistance of the EDLC cell made of the current collector with the carbon fiber layer was reduced compared to the cell using the pristine current collector. The interfacial resistance decreased from 0.0143 Ω·cm² to a maximum of 0.0077 Ω·cm². And degradation reactions of the activated carbon electrodes are suppressed in the 3.3 V floating test. We infer that it is because the improved electric network of the carbon fiber layer coated on the current collector surface enhanced the electron collection and interfacial diffusion while protecting the surface of the cathode etched aluminum; thereby suppressing the formation of Al-F compounds.

• The Journal of Korean Institute of Next Generation Computing
• /
• v.13 no.4
• /
• pp.40-51
• /
• 2017

Recently, as mobile workloads are becoming more data-intensive, high data bandwidth is required for mobile memory which also consumes non-negligible system energy. A variety of researches and technologies are under development to improve and optimize mobile memory technologies. However, a comprehensive study on the latest mobile memory technologies (LPDDR or Wide I/O) has not been extensively performed yet. To construct high-performance and energy-efficient mobile memory systems, quantitative and detailed analysis of these technologies is crucial. In this paper, we simulate the computer system which adopts mobile DRAM technologies (Wide I/O and LPDDR3). Based on our detailed and comprehensive results, we analyze important factors that affect performance and energy-efficiency of mobile DRAM technologies and show which part can be improved to construct better systems.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.6
• /
• pp.1057-1066
• /
• 2023

Global Navigation Satellite System (GNSS) is one of the core technologies for the 4th Industrial Revolution, and its importance is increasingly highlighted in the next generation communications and smart mobility requiring the accurate location information. As the development of the high-performance/high-precesion GNSS technology makes it possible to obtain the more accurate locations information, the location based products and systems, which provide the high-quality service, are being researched/developed. In this paper, we present the results of a survey on the recent research trends and examples, utilizing GNSS technology in fields of the next generation communications and smart mobility, and analyzes the results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.397-400
• /
• 2000

The demands of high data transfer rate and high recording density in optical disk memory device are being increased. In order to achieve high performance, lever actuator for optical disk is proposed. Firstly, the role of lever and structure are discussed and the flexure hinge is introduced to enhance the precise movement. Next is to present the magnetic circuit structure and concept design for the lever actuator. Finally, the dynamic modeling of the lever actuator is found and the analysis results are shown. Consequently, the lever actuator shows the possibility as a pickup actuator for the next generation optical disk.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.835-840
• /
• 2008

Next Generation High Speed Train having a distributed electrical motor system has just been developing to aim the experimental maximum speed at 400km/h since August, 2007. This project is in stage of concept design and so, it needs to take some review and analysis the characteristics of suspensions on the view of concept design. A vehicle modeling is made of modified Korean High Speed Train bogie model with Vampire program and analyzed the effect on the dynamic performances according to the variation of primary and secondary suspension characteristics. The results would be useful to manage the potential risks in the next stage of basic and precision design that will be done by the manufacturing company.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.325-329
• /
• 2003

Nowadays many peoples are using helicopter in various fields, not only military use but also common people applications such as air-measurement, photography, transportation of goods and persons, saving life and fire fighting etc. And it will be expected more popular than now. Most important part of helicopter to increasing performance and to reducing noise is rotor hub-system. Hub system consists of rotor-blade and rotor-hub. We participate to develop next-generation rotor hub system with elastomeric bearing, part of rotor hub. In this paper we introduce about the role and shape of elastomeric bearing in next-generation helicopter hub system. Then we study about bearing-material requirements and measuring methods. Finally we represent some experimental results.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.387-392
• /
• 2008

Next Generation High Speed Train having a distributed electrical motor system has just been developing to aim the experimental maximum speed at 400km/h since August, 2007. This project is in stage of concept design and so, it needs to take some review and analysis the characteristics of suspensions on the view of concept design. A train dynamic modeling is modified with the one car model presented in the previous conference and it was extended to 6cars models having the same suspensions and added some connection's characteristics between the cars with Vampire program. It is used to analyze the effect on the dynamic performances according to the variation of primary and secondary suspension characteristics in the condition of 6 cars configuration. The results would be useful to manage the potential risks in the next stage of basic and critical design that will be done by the manufacturing company.