• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3109-3117
• /
• 1994

To operate a flexible mechanism in high speed its weight must be reduced as far as the structural strength does not decrease too much, but a light-weighted mechanism causes undesirable elastodynamic responses deteriorating the system performance. Besides, clearance within the connections of mechanisms causes rapid wear, increased noise and vibration. Even if the problems described above must be considered in the initial design stage, there has been no effective design process which takes account of the correlation between dynamic characteristics of flexible mechanism and the clearance effect at the joint. In this study, the generalized elastodynamic governing equations which include dynamic characteristics and boundary conditions of flexible mechanism are derived by variational calculus and solved by using FFM theory. To take the clearance effect at joint into account a new dynamic model is presented and also the method of modified stiffness/damping matrix is proposed to activate the dynamic clearance model, which cooperates with the developed governing equation very easily. As the results of this study, the proposed method(modified stiffness/damping matrix) to calculate clearance effect was proved to be superior to the existing one(force reaction method) in solution convergency and calculation performance. Besides this method can be easily adopted to the complex shape joint without calculation of reaction force direction.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.618-623
• /
• 2011

A pressure control law to regulate pressure of gas generator is suggested. To design a model based control law, the governing equation which is consisted of Robert and conservation equation is built and verified through the ground burning test. PID and nonlinear adaptive control laws are designed to evaluate the loop response characteristics under the system which has varying eigen properties as combustor volume is increased. It is suggested that new approach, gain scheduling design, is required to overcome the defects identified from numerical simulation results of the two control laws. The newly suggested scheme showed good control performance even under disturbances and measurement noise.

• Journal of the Korean Society of Safety
• /
• v.22 no.3 s.81
• /
• pp.51-56
• /
• 2007

In recent years, many research works have been carried out in order to obtain a more controlled durability and long-term performance of concrete structures in chloride containing environments. In particular, the development of new procedures for probability-based durability analysis/design has proved to be very valuable. Although there is still a lack of relevant data, this approach has been successfully applied to some new concrete structures. In this paper, the equation used for modelling of the chloride penetration was based on Fick's Second Law of Diffusion in combination with a time dependent diffusion coefficient. The probability analysis of the durability performance was performed by use of a Monte Carlo Simulation. The procedure was applied to an example based on limited data gathered in this country. The influences of each parameter on the durability of concrete structures are studied and some comments for durability design are given. The new procedure may be very useful in designing an important concrete structures in chloride containing environments. Also it may help to predict the service life of concrete structures under a given probability of failure.

• Wind and Structures
• /
• v.15 no.5
• /
• pp.409-421
• /
• 2012

In this paper, the method of introducing additional source/sink terms in the turbulence and momentum transport equations was applied to appropriately model the effect of the tree canopy. At first, the new additional source term for the turbulence frequency ${\omega}$ equation in the SST k-${\omega}$ model was proposed through theoretical analogy. Then the new source/sink term model for the SST k-${\omega}$ model was numerically verified. At last, the proposed source term model was adopted in the wind environment optimal design of the twin high-rise buildings of CABR (China Academy of Building Research). Based on the numerical simulations, the technical measure to ameliorate the wind environment was proposed. Using the new inflow boundary conditions developed in the previous studies, it was concluded that the theoretically reasonable source term model of the SST k-${\omega}$ model was applicable for modeling the tree canopy flow and accurate numerical results are obtained.

• Water for future
• /
• v.19 no.1
• /
• pp.57-63
• /
• 1986

The synthetic unit hydrograph is commonly used for the derivation of a design hydregraph. The existing Snyder's equation for the syntheses of unit hydrograph was found to give relatively a flat hydrograph in comparison with observed hydrograph and a revision is required. HEC-1 model is used to simulated observed hydrograhp in the South Han River basin and results are used as an input for the regression. The basin is subdivided into small drainage areas and the synthesized hydrograph is routed through channels. After the calculated hydrographs are compared with observed one, the synthesized hydrograph of each subbasisn is revised and the new snyder's equation is derived . The revised equation gives rapid increase of discharge in rising limb and larger peak.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.5
• /
• pp.687-694
• /
• 1999

This study was conducted to develop new drying process for automatic control and marine engi-neering system. Air-water tests were carried out to investigate dryer performance. The dispersed flow in he dryer test apparatuses was also simulated by using a numerical code which solves the Dittus-Boelter equation for continuous liquid phase and the Reynolds equation of droplet motion for continuous liquid phase and the Reynolds equation of droplet motion for dispersed phase to predict droplet removal efficiency. Proper conditions for dehumidification were optimized by response ambient conditions. When the selected indexes were constrained in the range of 85-98% moisture content above $15^{\circ}$ and more than mass flow rates of moist air 750kg/h. The numerical results were compared with the experimental data pertaining to the removal effi-ciency at chamber stage and overall pressure drop along concentric tubes Good agreement was obtained as for the efficiency while relatively poor agreement was obtained for the relative humidity. The results also showed that the efficiency depended strongly on the relative humidity at the inlet condition which indicated the importance of estimating the heat exchanger length. Effects of some design parameters in both removal efficiency and breakthrough onset condition are discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.692-695
• /
• 2000

This paper is concerned with Accuracy Design of LM Guide System in Machine Tools. Elastic deformation of bearing is calculated by Hertz contact theory and motion error of LM block is analyzed. A new algorithm using block stiffness is proposed fur the analysis of motion accuracy of the table. The best advantage of this algorithm is fast analysis speed because it isn't necessary iteration processes for satisfying equilibrium equation of the table. Motion errors of the table analyzed under artificial form error of rail theoretically and experimentally. Only one of two rails is bent by putting a thickness gauge into horizontal direction. This form error of rail is measured by gap sensor against the other rail. Then, motion errors of the table are predicted by proposed new algorithm theoretically and measured by laser interferometer. Measurements are carried out by changing the preload and thickness. The results show that the table motion errors are reduced from 1/2 to 1/60 times than form error of rail according to its height and width. And the effect of preloading is almost negligible.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.9
• /
• pp.758-767
• /
• 2000

The properties of linear time-varying(LTV) systems vary because of the time-varying property of plant parameters. The generalized controller design method for linear time-varying systems does not exit because the analytic soultion of dynamic equation has not been found yet. Hence, to design a controller for LTV systems, the robust control methods for uncertain LTI systems which are the approximation of LTV systems have been generally ised omstead. However, these methods are not sufficient to reflect the fast dynamics of the original time-varying systems such as missiles and supersonic aircraft. In general, both the performance and the robustness of the control system which is designed with these are not satisfactory. In addition, since a better model will give the more robustness to the controlled system, a gain scheduling technique based on LTI controller design methods has been uesd to solve time problem. Therefore, we propose a new gain scheduled QFT method for LTV systems based on neural networks in this paper. The gain scheduled QFT involves gain dcheduling procedured which are the first trial for QFT and are well suited consideration of the properties of the existing QFT method. The proposed method is illustrated by a numerical example.

• Journal of Hydrogen and New Energy
• /
• v.32 no.6
• /
• pp.636-641
• /
• 2021

Using numerical analysis, various factors influencing the performance development of high-pressure pumps for Dimethyl Ether (DME) engines were identified and the impact of each factor was evaluated using Taguchi method. DME fuels are more compressive than diesel fuels and have the lower heat generation, so it is necessary to increase the size of the plunger and speed (RPM) of the pump as well. In addition, it is necessary to change the shape and design of control valve to control the discharge flow and pressure. In this study, various variables affecting the performance and flow rate increase of high-pressure pumps for DME engines are planned using Taguchi method, and the best design method is proposed using correlation of the most important variables. As a result, we were able to provide the design value needed for a six-liter engine and provide optimal conditions. The best combination factors to optimize the flow rate at RPM 2,000 and diameter plunger with 20 mm. The regression equation can also be used to optimize the flow rate; -8, 13+0, 2552 RPM +54, 17 diam. Plunger.

• The Journal of Industrial Distribution & Business
• /
• v.5 no.4
• /
• pp.13-22
• /
• 2014

Purpose - This study aims to examine new product adoption (NPA) in the context of clothing in Iran. Research design, data, and methodology - Data were gathered from cloth owners in Iran, focusing on famous cloth brands cloth. Further, using the proportionate stratified sampling method, a total 438 usable questionnaires were returned and analyzed through the use of structural equation modeling (SEM). In addition, LISREL software was used to analyze the data collected through the structured questionnaires. Results - Overall, the study findings indicate that education has a positive effect on new product adoption, whereas the impacts of religion and Attitude towards Consumption (ATC) on new product adoption are negative and significant, but the effect of age, peers, and income on new product adoption is not significant. Conclusions - Using date obtained from a large random sample of Iranian consumers, this study offers a deeper understanding of the attitudinal and personal antecedents of consumers' new product adoption in an emerging market. Using the findings of the articles and conclusions will be useful for market researchers and, of course, business persons.