• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.8
• /
• pp.52-59
• /
• 1998

New types of PFD (phase-frequency detector) are proposed with reset time and propagation delay reduced. The perfomrance of our proposed PFDs are confirmed by SPICE simulation with 0.8.mu.m CMOS process parameter. As a result of simulation, the reset time of PFDs are 0.32 nsec and 0.030 nsec in capture-process. The proposed PFDs can be used in hihg-speed phase-licked loop (PLL).

• ETRI Journal
• /
• v.29 no.1
• /
• pp.110-112
• /
• 2007

As an alternative to the classic linear detector which only assumes noise variance, a new robust detector with noise variance estimation censoring input signals over AWGN is proposed. The results demonstrate that analytic detection probability matches the simulation results for the linear detector and that the new robust detector shows better performance than the linear detector when the number of samples increases.

• ETRI Journal
• /
• v.28 no.3
• /
• pp.355-363
• /
• 2006

This paper presents a low-cost RF parameter estimation technique using a new RF built-in self-test (BIST) circuit and efficient DC measurement for 4.5 to 5.5 GHz low noise amplifiers (LNAs). The BIST circuit measures gain, noise figure, input impedance, and input return loss for an LNA. The BIST circuit is designed using $0.18\;{\mu}m$ SiGe technology. The test technique utilizes input impedance matching and output DC voltage measurements. The technique is simple and inexpensive.

• Korean Journal of Computational Design and Engineering
• /
• v.10 no.4
• /
• pp.284-292
• /
• 2005

This paper presents a new framework of kinematic tolerance synthesis and describes the implemented algorithm for planar mechanical systems comprised of higher kinematic pairs. Input to the synthesis algorithm is a parametric model of the mechanical system with allowed parameter ranges (tolerance ranges). The model is specified as the part profiles consisting of line and arc segments and the motion axes along which each part moves. The algorithm analyzes tolerance in generalized configuration space, called contact zones bounding the worst-case variations, and identifies bad system variations. The bad system variations then are removed out of the parameter ranges by adjusting the nominal parameter values if possible and then shrinking the ranges otherwise. This cycle is repeated until no more bad variations we found. I show the effectiveness of the algorithm by case studies on several mechanisms.

• Structural Engineering and Mechanics
• /
• v.60 no.3
• /
• pp.471-488
• /
• 2016

This study predicts the strength of rotary brace damper by analyzing a new set of probabilistic models using the usual method of multiple linear regressions (MLR) and advanced machine-learning methods of multivariate adaptive regression splines (MARS), Rotary brace damper can be easily assembled with high energy-dissipation capability. To investigate the behavior of this damper in structures, a steel frame is modeled with this device subjected to monotonic and cyclic loading. Several response parameters are considered, and the performance of damper in reducing each response is evaluated. MLR and MARS methods were used to predict the strength of this damper. Displacement was determined to be the most effective parameter of damper strength, whereas the thickness did not exhibit any effect. Adding thickness parameter as inputs to MARS and MLR models did not increase the accuracies of the models in predicting the strength of this damper. The MARS model with a root mean square error (RMSE) of 0.127 and mean absolute error (MAE) of 0.090 performed better than the MLR model with an RMSE of 0.221 and MAE of 0.181.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.1
• /
• pp.87-94
• /
• 2011

Characteristics of two-phase pressure drop in microchannels were investigated experimentally. The microchannels consisted of 9 parallel trapezoidal channels with each channel having $205\;{\mu}m$ of bottom width, $800\;{\mu}m$ of depth, $3.6^{\circ}$ of sidewall angle, and 7 cm of length. Pressure drops in convective boiling of Refrigerant 113 were measured in the range of inlet pressure 105~195 kPa, mass velocity $150{\sim}920\;kg/m^2s$, and heat flux $10{\sim}100\;kW/m^2$. The total pressure drop generally increased with increasing mass velocity and/or heat flux. Two-phase frictional pressure drop across the microchannels increased rapidly with exit quality and showed bigger gradient at higher mass velocity. A critical review of correlations in the literature suggested that existing correlations were not able to match the experimental results obtained for two-phase pressure drop associated with convective boiling in microchannels. A new correlation suitable for predicting two-phase friction multiplier was developed based on the separated flow model and showed good agreement with the experimental data.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.55-59
• /
• 2013

A new method using RF Ids determined from measured S-parameters is proposed to extract the gate-voltage dependent effective carrier velocity of bulk MOSFETs in the saturation region without additional dc Ids measurement data suffering parasitic resistance effect that becomes larger with continuous down-scaling to sub-$0.1{\mu}m$. This method also allows us to extract the carrier velocity in the saturation region without the difficult extraction of bias-dependent parasitic gate-source capacitance and effective channel length. Using the RF technique, the electron velocity overshoot exceeding the bulk saturation velocity is observed in bulk N-MOSFETs with a polysilicon gate length of $0.065{\mu}m$.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.3
• /
• pp.204-208
• /
• 1991

Five models for net radiation estimation reported by Linacre(1968), Berljand(1956), Nakayama et al. (1983), Chang (1970) and Doorenbos et al. (1977) were tested for the adaptability to Korea. A new model with effective longwave radiation term parameterized by air temperature, solar radiation and vapor pressure was formulated and tested for its accuracy. Above five models with original parameter values showed large absolute mean deviations ranging from 0.86 to 1.64 MJ/$m^2$/day. The parameters of the above five models were reestimated by using net radiation and meteorological elements measured in Suwon, Korea. These five models with new parameter values showed absolute mean deviations ranging from 0.74 to 0.88 MJ/$m^2$/day. The following model was newly formulated: Rn=(1- $\alpha$) Rs- $\sigma$ $T_{k}$$^{4}$ (0.0103 Exp (0 .0731 Rs) -0.0475 (equation omitted) +0 .2478) ($R^2$=0.997, n=63) where $\alpha$ =albedo, $\sigma$=Stefan-Boltzmann constant, Rs=solar radiation in MJ/$m^2$/day, Tk =air temperature in Kelvin and $e_{a}$=vapor pressure in mb. This model revealed 0.4988 MJ/$m^2$/day in absolute mean deviation when applied to an independent set of meteorological data.a.a.

• Journal of IKEEE
• /
• v.18 no.2
• /
• pp.272-281
• /
• 2014

In electrical impedance tomography (EIT), modified Newton Raphson (mNR) method is widely used inverse algorithm for static image reconstruction due to its convergence speed and estimation accuracy. The unknown conductivity distribution is estimated iteratively by minimizing a cost functional such that the residual error namely the difference in measured and calculated voltages is reduced. Although, mNR method has good estimation performance, EIT inverse problem still suffers from ill-conditioned and ill-posedness nature. To mitigate the ill-posedness, generally, regularization methods are adopted. The inverse solution is highly dependent on the choice of regularization parameter. In most cases, the regularization parameter has a constant value and is chosen based on experience or trail and error approach. In situations, when the internal distribution changes or with high measurement noise, the solution does not get converged with the use of constant regularization parameter. Therefore, in this paper, in order to improve the image reconstruction performance, we propose a new scheme to determine the regularization parameter. The regularization parameter is computed based on residual error and updated every iteration. The proposed scheme is tested with numerical simulations and laboratory phantom experiments. The results show an improved reconstruction performance when using the proposed regularization scheme as compared to constant regularization scheme.

• Nuclear Engineering and Technology
• /
• v.49 no.6
• /
• pp.1240-1249
• /
• 2017

An essential component of the neutron transport solver is the resonance self-shielding calculation used to determine equivalence cross sections. The neutron transport code, MPACT, is currently using the subgroup self-shielding method, in which the method of characteristics (MOC) is used to solve purely absorbing fixed-source problems. Recent efforts incorporating multigroup kernels to the MOC solvers in MPACT have reduced runtime by roughly $2{\times}$. Applying the same concepts for self-shielding and developing a novel lumped parameter approach to MOC, substantial improvements have also been made to the self-shielding computational efficiency without sacrificing any accuracy. These new multigroup and lumped parameter capabilities have been demonstrated on two test cases: (1) a single lattice with quarter symmetry known as VERA (Virtual Environment for Reactor Applications) Progression Problem 2a and (2) a two-dimensional quarter-core slice known as Problem 5a-2D. From these cases, self-shielding computational time was reduced by roughly $3-4{\times}$, with a corresponding 15-20% increase in overall memory burden. An azimuthal angle sensitivity study also shows that only half as many angles are needed, yielding an additional speedup of $2{\times}$. In total, the improvements yield roughly a $7-8{\times}$ speedup. Given these performance benefits, these approaches have been adopted as the default in MPACT.