• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.61-66
• /
• 2012

Conventional method to transform vehicle driving condition to engine operation mode is to use vehicle road load under neutral gear and mechanical efficiency of drivetrain. But this method requires additional measurement of efficiency of drivetrain on a test rig. And this measurement is normally done at fixed speed and thus estimated accuracy of engine operation mode is not considered to be high enough. This study suggests new method to calculate engine operation mode for prescribed driving mode such as NEDC using vehicle coastdown test under gear engaged condition without measurement of mechanical efficiency of drivetrain. Coastdown test was done under neutral and gear engaged condition for comparison and also trial to extract mechanical loss of drivetrain was carried out. Calculated engine torque by conventional and newly suggested method was compared with actually measured torque of a vehicle on a chassis dynamometer during NEDC. Newly suggested method showed slightly higher accuracy of accumulated brake work during NEDC.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1306-1315
• /
• 2016

Modern power systems driven by high-power converters have become inevitable in view of the ever increasing demand for electric power. The total power loss can be reduced by limiting the switching losses in such power converters; increased power efficiency can thus be achieved. A reduced switching frequency that is less than a few hundreds of hertz is applied to power converters that produce output waveforms with high distortion. Selective harmonic elimination pulse width modulation (SHEPWM) is an optimized low switching frequency pulse width modulation method that is based on offline estimation. This method can pre-program the harmonic profile of the output waveform over a range of modulation indices to eliminate low-order harmonics. In this paper, a SHEPWM scheme for three-phase three-leg neutral point clamped inverter is proposed. Aside from eliminating the selected harmonics, the DC capacitor voltages at the DC bus are also balanced because of the symmetrical pulse pattern over a quarter cycle of the period. The technique utilized in the estimation of switching angles involves the firefly algorithm (FA). Compared with other techniques, FA is more robust and entails less computation time. Simulation in the MATLAB/SIMULINK environment and experimental verification in the very large scale integration platform with Spartan 6A DSP are performed to prove the validity of the proposed technique.

• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.212-221
• /
• 2017

Permanent-Magnet Synchronous Generators (PMSGs) are used widely in Wind Power Generation Systems (WPGSs), and the Vienna rectifier was recently proposed to be used as the generator-side converter to rectify the AC output voltage in PMSG-based WPGS. Compared to conventional six-switch two-level PWM (2L-PWM) converters, the Vienna rectifier has several advantages, such as higher efficiency, improved total harmonic distortion, etc. The motivation behind this paper is to verify the performance of direct-driven PMSG wind turbine system based-Vienna rectifier by using a simulated direct-driven PMSG WPGS. In addition, for the purpose of reducing the reactive power loss of PMSGs, this paper proposes an induced voltage sensing scheme which can make the stator current maintain accurate synchronization with the induced voltage. Meanwhile, considering the Neutral-Point Voltage (NPV) variation in the DC-side of the Vienna rectifier, a NPV balancing control strategy is added to the control system. In addition, both the effectiveness of the proposed method and the performance of the direct-driven PMSG based-Vienna rectifier are verified by simulation and experimental results.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.129-136
• /
• 2006

Although cleaner and cheaper deinking of ONP could be performed at the neutral or low alkaline condition excessive loss from froth-flotation is unavoidable and so reduction of alkali or caustic soda dosage sacrifices recycling yield. Now the new trade-off regarding alkali dosage versus flotation yield is urgently required in order to set the optimized neutral or low alkaline deinking process of ONP. Lipase from Thermomyces Lanuginosus has an effect on desizing and deacetylation reaction and it could be applied to the stock of pre flotation secondary stage in order to reduce the flotation reject without the sacrifice of optical properties of flotation accepts. Instead of inorganic base, lipase could be applied as a biochemical catalyst for the selective modification of valuable hydrophobic particles in deinking stock, for example cellulose fines and inorganic fillers covered by hydrophobic additives or contaminants. When the enzymatic hydrolysis of ester bond could be made on the surface of hydrophobic particulates, unwanted float of fine particles could be prevented. Now the enhancement of flotation selectivity or the modification of the hydrophobicity of deinking stock is expected to be promoted by the enzymatic pre treatment. And the reduction of recycling cost with the saves of raw material, recovered paper would be possible as a result.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.63.4-64
• /
• 2018

High resolution spectroscopy of the yellow symbiotic star AG Draconis is performed with the Canada-France-Hawaii Telescope to analyse the line profiles of Raman scattered O VI broad emission features at $6825{\AA}$ and $7082{\AA}$ with a view to investigating the wind accretion process from the mass losing giant to the white dwarf. These two spectral features are formed through inelastic scattering of O $VI{\lambda}{\lambda}32$ and 1038 with atomic hydrogen. We find that these features exhibit double-component profiles with red parts stronger than blue ones with the velocity separation of ~ 60 km s-1 in the O VI velocity space. Monte Carlo simulations for O VI line radiative transfer are performed by assuming that the O VI emission region constitutes a part of the accretion flow around the white dwarf and that Raman O VI features are formed in the neutral part of the slow stellar wind from the giant companion. The overall Raman O VI profiles are reasonably fit with an azimuthally asymmetric accretion flow and the mass loss rate ~ 4 ${\times}$ 10^{-7} M_sun yr^{-1}. We also find that additional bipolar neutral regions moving away with a speed ~ 70 km s^{-1} in the directions perpendicular to the orbital plane provide considerably improved fit to the red wing parts of Raman features.

• KDI Journal of Economic Policy
• /
• v.29 no.2
• /
• pp.177-196
• /
• 2007

This paper analyzes welfare effects of revenue neutral tax reform using a small open economy dynamic general equilibrium model. We apply this model to the Korean data and examine welfare effects of various tax reforms; removal of capital income tax and/or labor income tax financed by consumption tax. We investigate both long run equilibrium and transitional dynamics. The results suggest that there are sizable welfare gains (1-3% of lifetime consumption) when factor income taxes are replaced by consumption tax. Overall gains are generated by long run gains despite short run welfare losses. However, there is welfare loss when capital income tax is replaced by labor income tax.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.7
• /
• pp.1196-1204
• /
• 1997

Cotton, rayon/cotton, and Tencel twill weave fabrics were used to investigate the effect of fiber types on the cellulase washing finish. And twill. basket, and derivative weave cotton fabrics were used to study the weave effect. Various fabrics were treated with neutral cellulase varying treatment times and with acid cellulase, stone, and stone-neutral cellulase respectively for two hours in a rotary washer. Weight loss decreased in the order of rayon/cotton> cotton> Tencel, and basket and derivative weave fabrics lost more weight than twill weave fabric. Color difference decreased in the order of cotton> Tencel> rayon/cotton, and twill weave fabric had larger color difference than derivative and basket weave fabrics. Back staining decreased in the order of cotton> rayon/cotton> Tencel, and twill weave fabric had larger back staining than derivative and basket weave fabrics. Tear strength retention decreased in the order of rayon/cotton> cotton> Tencet and twill weave fabric had larger tear strength retention than derivative and basket weave fabrics. Flex stiffness retention decreased in the order of cotton> Tencel> rayon/cotton, and in the order of derivative> twill> basket weave. In cotton fibers, damage of primary wall was observed. And the cellulase treatment on Tencel seemed to roughen the fabric surface slightly, and to fibril fibers along the fiber axis.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.504-517
• /
• 2015

This paper presents a novel switching voltage model and an offset-based pulse width modulation (PWM) scheme for multilevel inverters with unbalanced DC sources. The switching voltage model under a DC voltage imbalance will be formulated in general form for multilevel neutral-point-clamped topologies. Analysis of the reference switching voltages from active and non-active switching voltage components in abc coordinates can enable voltage implementation for an unbalanced DC-source condition. Offset voltage is introduced as an indispensable variable in the switching voltage model for multilevel voltage-source inverters. The PWM performance is controlled through the design of two offset components in a subsequence. One main offset may refer to the common mode voltage, and the other offset restricts its effect on the quality of PWM control in related DC levels. The PWM quality can be improved as the switching loss is reduced in a discontinuous PWM mode by setting the local offset, which is related to the load currents. The validity of the proposed algorithm is verified by experimental results.

• Textile Coloration and Finishing
• /
• v.19 no.3
• /
• pp.1-5
• /
• 2007

The advantage of enzyme scouring over alkali scouring is that the enzymatic process can be carried in a neutral pH, resulting in less damage on the fibers and a drastic reduction of wastewater. Since the pH of scouring bath is neutral, dyeing can be carried in the same bath. Four different types of scouring and dyeing in a single-bath were performed in this work: continuous scouring and dyeing in one-bath I and II, simultaneous scouring and dyeing in one-bath I and II. The difference between process I and II is the existence of an after-treatment process in the scouring. Dyeing was performed with three major colors(red, blue, yellow) and black to investigate the dye-ability. The absorbency of scoured and dyed fabrics was measured using gravimetric absorbency testing system. The fabric weight loss was measured after the treatment. Although the color depth for the three major colored fabrics treated in a single-bath was lower than the fabric scoured and dyed separately, the fabrics dyed with black did not show much difference. In addition, the absorbency of fabric treated in a single-bath was higher than the fabric treated separately.

• Nuclear Engineering and Technology
• /
• v.56 no.4
• /
• pp.1145-1152
• /
• 2024

To realize an initial objective of the negative ion-based neutral beam injection (N-NBI) at the Comprehensive Research Facility for Fusion Technology (CRAFT) test facility, which targets an H⁰ beam power of 2 MW at an energy of 200-400 keV and a pulse duration of 100 s, it is crucial to study the cesium dynamics of the negative ion source. Here a numerical simulation program CSFC3D is developed and applied to simulate the distribution and time dynamics of cesium during short pulses. The calculations show that most of the cesium on the plasma grid (PG) area originates from the release of cesium that is accumulated within the ion source in the plasma phase. Increasing the wall temperature reduces the loss of cesium on the wall of the ion source. Furthermore, the thickness of the cesium monolayer is directly influenced by the PG temperature. Both simulated and experimental results demonstrate that maintaining the PG temperature between 180 ℃ and 200 ℃ is essential for enhancing the performance of the ion source and optimizing the cesium behavior.