• Journal of Soil and Groundwater Environment
• /
• v.9 no.3
• /
• pp.38-48
• /
• 2004

Natural attenuation of petroleum hydrocarbon was investigated at an industrial complex about 45 Km away from Seoul. The three-years monitoring results indicated that the concentrations of DO, nitrate, and sulfate in the contaminated area were significantly lower than the background monitoring groundwater under the non-contaminated area. The results also showed a higher ferrous iron concentration, a lower redox potential, and a higher (neutral) pH in the contaminated groundwater, suggesting that biodegradation of TEX(Toluene, Ethylbenzene, Xylene) is the major on-going process in the contaminated area. Groundwater in the contaminated area is anaerobic, and sulfate reduction is the dominant terminal electron accepting process in the area. The total attenuation rate was about 0.0017∼0.0224day$^{-1}$ and the estimated first-order degradation rate constant(λ) was 0.0008∼0.0106day$^{-1}$ . However, the reduction of TEX concentration in the groundwater was resulted from not only biodegradation but also dilution and reaeration through recharge of uncotaminated surface and groundwater. The natural attenuation was, therefore, found to be an effective, on-going remedial process at the site.

• Applied Chemistry for Engineering
• /
• v.23 no.6
• /
• pp.521-528
• /
• 2012

In this study, we analyzed the physical properties of an ethylene oxide adducted amphoteric surfactant such as critical micelle concentration, surface tension, interfacial tension, contact angle, viscosity and phase behavior. The dual function characteristics of an amphoteric surfactant were investigated by determining an isoelectric point, which were attained using zeta potential measurements and quartz crystal microbalance (QCM) experiments. The isoelectric points of DE3-OSA82-AO, DE5-OSA82-AO and DE9-OSA82-AO surfactant systems determined by zeta potential measurements were 6.97, 6.93 and 7.10 respectively and they are in good agreement with the isoelectric point values measured by QCM experiments. The frictional property measured using an automated mildness tester showed that the DE-OSA82-AO surfactant could provide a good softening effect at neutral condition.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.36 no.1
• /
• pp.34-40
• /
• 2016

The objective of this study was to determine the effect of moisture content on the physical and chemical characteristics of Italian ryegrass cube. Cube quality according to moisture contents (15, 20, 25, and 30%) was determined. Cubes made with 15 to 20% moisture showed a little cracks. But, the amount of powder generate from these cubes were lower by 10 to 16% compared to other cubes made with 25 to 30% moisture contents. The highest hardness at 159 kg/f was obtained when the cube was made with 15% moisture content and the lowest was 70 kg/f when the cube was made with 30% moisture content. The electrical loading and surface temperature were increased when moisture content was decreased. The chemical compositions of cube were differ from those of raw materials. Crude protein (CP) and ether extract (EE) contents were increased after cubing works. However, crude fiber (CF), acid detergent fiber (ADF), and neutral detergent fiber (NDF) contents were decreased after cubing. The crude ash content was not significantly (p > 0.05) different between raw material and cube. Higher moisture content resulted in higher crude protein content. However, crude fiber and crude ash content were not significantly (p > 0.05) different between each other. The contents of ADF and NDF were the lowest in cubes made with 30% moisture content. Our results suggest that the proper moisture content of Italian ryegrass cubing is recommended to be 15 to 20% and that cubing works should help increase forage quality.

• Economic and Environmental Geology
• /
• v.38 no.1
• /
• pp.23-31
• /
• 2005

This study was performed to investigate the effect of humic acid on the adsorption of arsenic onto hematite and its binding mechanism through the chemical speciation modeling in the binary system and the adsorption modeling in the ternary system. The complexation modeling of arsenic and humic acid was suitable for the binding model with the basis of the electrostatic repulsion and the effect of bridging metal. In comparison with the experimental adsorption data in the ternary system, the competitive adsorption model from the binary intrinsic equilibrium constants was consistent with the amount of arsenic adsorption. However, the additive rule showed the deviation of model in the opposite way of cationic heavy metals, because the reduced organic complexation of arsenic and the enhanced oxyanionic competition diminished the adsorption of arsenic. In terms of the reaction mechanism, the organic complex of arsenic, neutral As(III) and oxyanionic As(V) species were transported and adsorbed competitively to the hematite surface forming the inner-sphere complex in the presence of humic acid.

• Journal of Mushroom
• /
• v.20 no.4
• /
• pp.263-269
• /
• 2022

This study investigated the culture characteristics of Cryptoporus volvatus, whichis grow naturally in Korea, to determine the suitable environmental conditions for its cultivation. The physiological characteristics of the mycelia were assessed according to the cultivation conditions, to determine the optimal conditions for artificial cultivation. The visual characteristics of the hyphae of Cryptoporus volvatus KACC52303 included an irregular and uneven surface and a fuzzy or cotton-like texture. Under the microscope, its microstructure showed pre-chlamydospore formation, but no clamps were seen. The appropriate culture temperature was found to be a medium/high temperature of approximately 25-30℃, and the optimal pH was found to have a wide range from weakly acidic (pH 4) to neutral (pH 7). In the optimal nutrient source experiment, hyphal growth was shown to be fair in a mixed medium with 2.5% dextrin as the carbon source and 0.1% yeast extract as the organic nitrogen source. Among the various amino acids, organic acids, and inorganic salts tested, the fastest hyphal growth was observed in the presence of leucine, acetic acid or gluconic acid, and KCl or KH₂PO₄, respectively. The column test showed that the best mycelial growth occurred in a mixed medium of 80% pine sawdust, 10% rice bran, and 10% corncob sawdust.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.3
• /
• pp.23-29
• /
• 2022

In this study, we investigated the ozone nanobubble process in which nanobubble and ultrasonic cavitation were applied simultaneously to improve the dissolution and self-decomposition of ozone. To confirm the organic decomposition efficiency of the process, a 200 mm × 200 mm × 300 mm scale reactor was designed and phenol decomposition experiments were conducted. The use of nanobubble was 2.07 times higher than the conventional ozone aeration in the 60 minutes reaction and effectively improved the dissolution efficiency of ozone. Ultrasonic irradiation increased phenol degradation by 36% with nanobubbles, and dissolved ozone concentration was lowered due to the promotion of ozone self-decomposition. The higher the ultrasonic power was, the higher the phenol degradation efficiency. The decomposition efficiency of phenol was the highest at 132 kHz. The ozone nanobubble process showed better decomposition efficiency at high pH like conventional ozone processes but achieved 100% decomposition of phenol after 60 minutes reaction even at neutral conditions. The effect by pH was less than that of the conventional ozone process because of self-decomposition promotion. To confirm the change in bubble properties by ultrasonic irradiation, a Zetasizer was used to measure the bubbles' size and zeta potential analysis. Ultrasonic irradiation reduced the average size of the bubbles by 11% and strengthened the negative charge of the bubble surface, positively affecting the gas transfer of the ozone nanobubble and the efficiency of the radical production.

• Clean Technology
• /
• v.28 no.2
• /
• pp.174-181
• /
• 2022

Biomass is a sustainable alternative resource for production of liquid fuels and organic compounds that are currently produced from fossil fuels including petroleum, natural gas, and coal. Because the use of fossil fuels can increase the production of greenhouse gases, the use of carbon-neutral biomass can contribute to the reduction of global warming. Although biological and chemical processes have been proposed to produce petroleum-replacing chemicals and fuels from biomass feedstocks, it is difficult to replace completely fossil fuels because of the high oxygen content of biomass. Production of petroleum-like fuels and chemicals from biomass requires the removal of oxygen atoms or conversion of the oxygen functionalities present in biomass derivatives, which can be achieved by catalytic hydrodeoxygenation. Hydrodeoxygenation has been used to convert raw biomass-derived materials, such as biomass pyrolysis oils and lignocellulose-derived chemicals and lipids, into deoxygenated fuels and chemicals. Multifunctional catalysts composed of noble metals and transition metals supported on high surface area metal oxides and carbons, usually selected as supports of heterogeneous catalysts, have been used as efficient hydrodeoxygenation catalysts. In this review, the catalysts proposed in the literature are surveyed and hydrodeoxygenation reaction systems using these catalysts are discussed. Based on the hydrodeoxygenation methods reported in the literature, an insight for feasible hydrodeoxygenation process development is also presented.

• Journal of Space Technology and Applications
• /
• v.3 no.1
• /
• pp.86-99
• /
• 2023

The mass spectrometer, being an essential scientific instrument for uncovering the origin of the solar system and life, has been used since the early 1970s on board spacecraft to obtain information of neutral and ionized elements in the atmosphere and surface of the moon, planets, asteroids, and comets. According to the 4th Basic Plan for the Promotion of Space Development (2023-2027), Korea plans to conduct lunar landing in 2032 and Mars landing in 2045 as the core goals of the plan and focuses on developing the technologies required for unmanned robotic exploration missions. In this regard, it is crucial to develop the technology of a mass spectrometer, which is the most fundamental payload for space exploration for maximized scientific achievements, however never tried before in any domestic space missions. We describe in this paper the principle of a domestically developed quadrupole mass spectrometer, its prototype model, and the test results of its performance. We conclude this paper with intended future improvements.

• Resources Recycling
• /
• v.33 no.3
• /
• pp.21-29
• /
• 2024

Globally, the demand for electric vehicles (EVs) is surging due to carbon-neutral strategies aimed at decarbonization. Consequently, the demand for lithium-ion batteries, which are essential components of EVs, is also rising, leading to an increase in the generation of spent batteries. This has prompted research into the recycling of spent batteries to recover valuable metals. In this study, we aimed to selectively leach and recover lithium from the cathode material of spent LFP batteries. To enhance the reaction surface area and reactivity, the binder in the cathode material powder was removed, and the material was subjected to heat treatment in both atmospheric and nitrogen environments across various temperature ranges. This was followed by a mechanochemical process for aqueous leaching. Initially, after heat treatment, the powder was converted into a soluble lithium compound using sodium persulfate (Na₂S₂O₈) in a mechanochemical reaction. Subsequently, aqueous leaching was performed using distilled water. This study confirmed the changes in the characteristics of the cathode material powder due to heat treatment. The final heat treatment in a nitrogen atmosphere resulted in a lithium leaching efficiency of approximately 100% across all temperature ranges.

• Journal of Korean Society of Forest Science
• /
• v.53 no.1
• /
• pp.44-55
• /
• 1981

Neutral sulfite precooked fir chips were refined in the Asplund Laboratory Defibrator at various temperature ($20^{\circ}C$, $120^{\circ}C$ and $180^{\circ}C$). The effects of refining temperatures on the physical property and morphological structure of the resulting pulps were discussed. Yields of precooked chips (84%, 92% and 100%) and refining temperature affected remarkably the yield of refined pulp, its beatability, sheet strength and morhphological characteristics. Pulp yield and beatability decreased with increasing refining temperature. Fiber surface of unbeaten pulp from precooked chips of 84% yield was to some extent covered by the secondary wall, while that of the pulp form precooked yield of 92% by the compound middle lamella. In the case of uncooked chips, fibers were damaged heavily, and the exposed fiber surface resulted from the equal amount of the secondary wall and the compound middle lamella. In the case of pulps prepared from precooked chips of higher yields (92% and 100%), sheet strength increased linearly as sheet density increased. But at the same sheet density, pulp from lower precooked yield (84%) had better sheet strength after open discharge refining as compared to pressurized refining, because pulp from the former had much amounts of fines fraction of higher water retention value than the latters. And there was observed a little difference in fiber length distribution but nearly similar in its morphology with increasing refining temperature.