• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.1 no.1
• /
• pp.105-111
• /
• 1997

This Paper Proposes a new efficient system design strategies for the acoustic-based underwater multiple modem and media access control protocol. The system aims to establish the acoustic-based communication network of an underwater vehicles for deep sea mining, which ensures a certain level of maximum throughput regardless of the propagation delay of acoustic and allows fast data transmission through the acoustic-based multiple channel. A media access control protocol for integrated communication network and it's acoustic-based communication modems that allows 'peer-to-peer' communication between a surface mining plant multiple underwater system is designed, and the proposed media access control protocol is implemented for its verification. Furthermore, a proposed design strategies which make it possible to control the multiple vehicle for an underwater mining is presented in this paper.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.9
• /
• pp.506-512
• /
• 2003

In this paper, a communication module between Relay agents in a multi-agent system based power distribution network protection system is realized using DNP3.0(Distributed Network Protocol), which is the standard communication protocol of distribution automation system in KEPCO. The key words for agent communication in the multi-agent based protection system are defined and represented by use of DNP application function code. The communication module developed based on the proposed communication scheme is tested by use of the Communication Test Harness, a test tool for DNP protocol, then used to the multi-agent system based power distribution net work protection system.

• International Journal of Computer Science & Network Security
• /
• v.23 no.10
• /
• pp.169-178
• /
• 2023

Wireless sensor network is wieldy use for IoT application. The sensor node consider as physical device in IoT architecture. This all sensor node are operated with battery so the power consumption is very high during the data communication and low during the sensing the environment. Without proper planning of data communication the network might be dead very early so primary objective of the cluster based routing protocol is to enhance the battery life and run the application for longer time. In this paper we have comprehensive of twenty research paper related with clustering based routing protocol. We have taken basic information, network simulation parameters and performance parameters for the comparison. In particular, we have taken clustering manner, node deployment, scalability, data aggregation, power consumption and implementation cost many more points for the comparison of all 20 protocol. Along with basic information we also consider the network simulation parameters like number of nodes, simulation time, simulator name, initial energy and communication range as well energy consumption, throughput, network lifetime, packet delivery ration, jitter and fault tolerance parameters about the performance parameters. Finally we have summarize the technical aspect and few common parameter must be fulfill or consider for the design energy efficient cluster based routing protocol.

• International Journal of Computer Science & Network Security
• /
• v.21 no.12
• /
• pp.1-8
• /
• 2021

In Mobile Ad-Hoc Network (MANET) Application, routing protocol is essential to ensure successful data transmission to all nodes. Ad-hoc On-demand Distance Vector (AODV) Protocol is a reactive routing protocol that is mostly used in MANET applications. However, the protocol causes Route Request (RREQ) message flooding issue due to the broadcasting method at the route request stage to find a path to a particular destination, where the RREQ will be rebroadcast if no Request Response (RREP) message is received. A scalable neighbor-based routing (SNBR) protocol was then proposed to overcome the issue. In the SNBR protocol, the RREQ message is only rebroadcast if the number of neighbor nodes less than a certain fix number, known as drop factor. However, since a network always have a dynamic characteristic with a dynamic number of neighbor nodes, the fix drop factor in SNBR protocol could not provide an optimal flooding problem solution in a low dense network environment, where the RREQ message is continuously rebroadcast RREQ message until reach the fix drop factor. To overcome this problem, a new broadcasting method as Dynamic SNBR (DSNBR) is proposed, where the drop factor is determined based on current number of neighbor nodes. This method rebroadcast the extra RREQ messages based on the determined dynamic drop factor. The performance of the proposed DSNBR is evaluated using NS2 and compared with the performance of the existing protocol; AODV and SNBR. Simulation results show that the new routing protocol reduces the routing request overhead, energy consumption, MAC Collision and enhances end-to-end delay, network coverage ratio as a result of reducing the extra route request messages.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.16 no.6
• /
• pp.247-251
• /
• 2021

We propose a protocol for Ethernet-based industrial real-time communication networks. In the protocol, the master periodically transmits control frames to all slaves, and the ring-type network topology is selected to achieve high-speed transmission speed. The proposed protocol is implemented in the form of both firmware and Linux kernel modules. To improve the transmission speed, the MAC address table is disabled in the firmware implementation, and the NAPI function of the Ethernet driver is removed in the Linux kernel module implementation. A network experiment environment is built with four ARM processor-based embedded systems and network operation experiments are performed for various frame sizes. From the experimental results, it is verified that the proposed protocol normally operates, and the firmware implementation shows better transmission speed than the Linux kernel module implementation.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.1
• /
• pp.199-204
• /
• 2011

This paper evaluates on the feasibility of MIL-STD-188-220 protocol as a medium access protocol over WNW(Wideband Network Waveform) by simulating and comparing with IEEE 802.11e-based protocol. WNW is newly designed waveform for next-generation broadband tactical communication system. This paper shows the feasibility of using the MIL-STD-188-220 protocol that shows better performance than IEEE 802.11e-based protocol on the particular environment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.175-180
• /
• 2002

In order to satisfy the requirements of time reduction and cost saving for development of electronic control systems(ECU) in automotive industry, the applications of a standardized real-time operating system(RTOS) and a communication protocol to ECUs are increased. In this study, a body control module(BCM) that employs OSEK/VDX(open system and corresponding interfaces for automotive electronics/vehicle distributed executive) OS tour the RTOS and a controller area network(CAN) fur the communication protocol is designed, and the performances of the system are evaluated. The BCM controls doors, mirrors, and windows of the vehicle through the in-vehicle network. To identify all the transmitted and received control messages, a PC connected with the CAN communication protocol behaves as a CAN bus emulator. The control system based upon in-vehicle network improves the system stability and reduces the number of wiring harness. Furthermore it is easy to maintain and simple to add new features because the system is designed based on the standards of RTOS and communication protocol.

• ETRI Journal
• /
• v.24 no.2
• /
• pp.69-81
• /
• 2002

This paper reviews the existing research activities on signaling and control procedures for IP over optical networks. We focus on the IP-centric signaling and control architecture based on the generalized multi-protocol label switching (GMPLS) protocol and analyze various scenarios and technical issues for deploying the IP over an optical network. We analyze the signaling and operations and administration and maintenance requirements for integrating an IP network and an optical network in order to cope with the high bandwidth and poor resource granularity of the optical network, including the optical cross-connect system. On the basis of network architecture and a reference configuration model, we investigate the GMPLS-based control architecture and interconnection model appropriate for controlling IP bandwidth and optical lambda resources. The signaling and control procedure based on GMPLS on optical user-network interface and network-network interface are comparatively investigated to provide the optical lightpath. We also study protection and restoration procedures to protect link failure when it applies to generalized MPLS signaling.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.1129-1132
• /
• 1999

This paper deals with the design and implementation of an Ethernet-based communication protocol to be used in PC-based I/O interface systems. Recently, the performance of PC systems is being highly improved and Ethernet is used as the stable communication network over the world. We develop a new protocol driver with the capability of accessing Ethernet directly using NDIS(Network Driver Interface Specification), the network interface standard of Windows O.S. in PC, and install it at the application layer of the protocol structure. Its major roles are the supplement of CSMA/CD algorithm, the effective use of the long data frame of Ethernet, and the real-time transmission of data frames. This paper represents the possibility of the real-time control network and systems based on PCs and Ethernet.

• International journal of advanced smart convergence
• /
• v.8 no.2
• /
• pp.109-115
• /
• 2019

Currently, LPWA(Low Power Wide Area) communication technology is widely used due to the development of IoT(Internet of Things) technology. Among the LPWA technologies, LoRaWAN(Long Range Wide Area Network) is widely used in many fields due to its wide coverage, stable communication speed, and low-cost modem module prices. In particular, LoRa(Long Range) can easily construct LoRaWAN with a dedicated gateway. So many organizations are building their own LoRaWAN-based networks. The LoRaWAN Gateway receives the LoRa packet transmitted from an End-device installed in the adjacent location, converts it into the Internet protocol, and sends the packet to the final destination server. Current LoRa Gateway uses a single-hop method, and each gateway must include a communication network capable of the Internet. If it is the mobile communication(i.e., WCDMA, LTE, etc.) network, it is required to pay the internet usage fee which is installed in each gateway. If the LoRa communication is frequent, the user has to spend a lot of money. We propose an idea on how to design a multi-hop protocol which enables packet routing between gateways by analyzing the LoRaWAN communication method implemented in its existing single-hop way in this paper. For this purpose, this paper provides an analysis of the standard specification of LoRaWAN and explains what was considered when such protocol was designed. In this paper, two gateways have been placed based on the functional role so as to make the multi-hop protocol realized: (i) hopping gateway which receives packets from the end-device and forwards them to another gateway; and (ii) main gateway which finally transmits packets forwarded from the hopping gateway to the server via internet. Moreover, taking into account that LoRaWAN is wireless mobile communication, a level-based routing method is also included. If the protocol proposed by this paper is applied to the LoRaWAN network, the monthly internet fee incurred for the gateway will be reduced and the reliability of data transmission will be increased.