• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2000년도 추계학술대회논문집
• /
• pp.133-136
• /
• 2000

We investigated the improvement of viewing angle using a patterned double twisted (PDT) vertical-alignment (VA) cell mode on a homeotropic alignment layer. Good voltage-transmittance curves for negative dielectric anisotropic nematic liquid crystal (NLC) using the PDT-VA cell without a negative compensation film were obtained. The viewing angle of the PDT-VA cell without a negative compensation film was wider than that of a conventional VA cell.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.133-136
• /
• 2000

We investigated the improvement of viewing angle using a patterned double twisted (PDT) vertical-alignment (VA) cell mode on a homeotropic alignment layer. Good voltage-transmittance curves for negative dielectric anisotropic nematic liquid crystal (NLC) using the PDT-VA cell without a negative compensation film were obtained. The viewing angle of the PDT-VA cell without a negative compensation film was wider than that of a conventional VA cell.

• Transactions on Electrical and Electronic Materials
• /
• 제11권1호
• /
• pp.42-47
• /
• 2010

Polymer insulating materials such as cross linked polyethylene (XLPE) are employed in electric cables used for extra high voltage. These materials can degrade due to chemical, mechanical and electric stress, possibly caused by voids, the presence of extrinsic materials and protrusions. Therefore, this study measured discharge patterns, discharge phase angle, quantity and occurrence frequency as well as changes in XLPE under different temperatures and applied voltages. To quantitatively analyze the irregular partial discharge patterns measured, the discharge patterns were examined using a statistical program. A three layer sample was fabricated, wherein the upper and lower layers were composed of non-void XLPE, while the middle layer was composed of an air void and copper particles. After heating to room temperature and $50^{\circ}C$ and $80^{\circ}C$ in silicone oil, partial discharge characteristics were studied by increasing the voltage from the inception voltage to the breakdown voltage. Partial discharge statistical analysis showed that when the K-means clustering was carried out at 9 kV to determine the void discharge characteristics, the amount discharged at low temperatures was small but when the temperature was increased to $80^{\circ}C$, the discharge amount increased to be 5.7 times more than that at room temperature because electric charge injection became easier. An analysis of the kurtosis and the skewness confirmed that positive and negative polarity had counterclockwise and clockwise clustering distribution, respectively. When 5 kV was applied to copper particles, the K-means was conducted as the temperature changed from $50^{\circ}C$ to $80^{\circ}C$. The amount of charge at a positive polarity increased 20.3% and the amount of charge at a negative polarity increased 54.9%. The clustering distribution of a positive polarity and negative polarity showed a straight line in the kurtosis and skewness analyses.

• 융합정보논문지
• /
• 제11권3호
• /
• pp.14-19
• /
• 2021

본 논문에서는 IT기기를 가동하기 위해 필요한 마이너스 전원을 저렴한 buck 소자를 이용해 안정된 방법으로 생성할 수 있는 inverter회로의 구성방법을 제시하였다. 이를 위해 기존의 buck 소자를 이용해 inverter 회로를 구성했을 경우의 문제점에 관해 살펴보고, 이러한 문제점을 방지할 수 있는 원리를 분석하고 해결할 수 있는 회로를 제시하였다. 제시한 방법의 효과를 입증하기 위해 실험회로를 구성하고 실험을 진행한 결과, 기존의 과전류 방지회로에 의한 inverter회로의 기동에 비해 과전류현상 없이 안정된 기동이 이루어짐을 확인하였다. 이에 따라 IT 기기에 사용되는 각종 아날로그 신호 처리를 위한 소자들을 편전원으로 구성하기 위한 수많은 주변소자들이 모두 생략될 수 있으면서도 회로의 성능을 크게 향상시킬 수 있을 것으로 기대된다.

• 한국정보통신학회논문지
• /
• 제16권6호
• /
• pp.1266-1272
• /
• 2012

게이트 길이와 폭이 다른 InGaZnO 박막 트랜지스터를 제작하고 소자의 크기에 따른 문턱전압과 음의 게이트 전압 스트레스 후의 소자 특성 저하에 관한 연구를 수행하였다. 게이트 길이가 짧은 소자는 문턱전압과 문턱전압 아래의 기울기 역수가 감소하였고 채널 폭이 작은 소자는 문턱전압이 증가 하였다. 음의 게이트 전압 스트레스 후에는 전달특성 곡선이 왼쪽으로 이동하였고 문턱전압은 감소하였으며 문턱전압 아래의 기울기 역수는 변화가 거의 없었다. 이러한 결과는 게이트 유전체에 포획된 홀 때문으로 사료된다. 게이트에 음의 스트레스 전압을 인가한 후에 게이트 길이가 짧을수록 그리고 게이트 폭이 증가할수록 문턱전압의 변화가 적은 것은 홀 주입이 적기 때문으로 사료된다.

• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2089-2097
• /
• 2014

Negative corona onset characteristics of the stranded conductors based on the ultra-high voltage (UHV) corona cage were studied in the paper. Based on the corona self-sustaining criterion in extreme uneven electric fields and the secondary emission process of the photoelectrons, the corona onset calculation model in the UHV corona cage is established and the corona current tests of the single LGJ900-75, 6 bundle LGJ900-75, 8 bundle LGJ400-35 conductors in dry and rain conditions were done in the UHV corona cage, and the rain rates are 2.4 mm/h, 20 mm/h and 30 mm/h. Corona onset electric field strength is gained by E-I tangent method, and the onset electric field strength in dry condition proves that the calculation model can be used to calculate the corona onset characteristics of the bundle conductors in the UHV corona cage. A further analysis proves that: the negative corona onset voltage of the conductor increases with the bundle number and the diameter of the sub conductor, but decreases with the bundle space in the corona cage. The onset electric field strength is influenced little by bundle space and bundle number, but decreases with the increase of the diameter of the sub-conductor. The surface irregularity coefficient decreases with the rain rate.

• 대한전자공학회논문지SD
• /
• 제39권12호
• /
• pp.1033-1044
• /
• 2002

본 논문에서는 grounded-plate PMOS 게이트 (GPPG) 강유전체 메모리 셀을 이용한 새로운 FRAM 설계기술을 제안하였다 GPPG 셀은 PMOS와 강유전체 커패시터로 구성되며 셀 plate 는 ground 에 접지 된다. 제안된 FRAM 에서는 비트라인이 V/sub DD/로 precharge 되고, negative 전압 워드라인 기법이 사용되며, negative 펄스 restore 동작을 이용한다 GPPG 셀을 이용한 FRAM 구조는 셀 plate 구동기폭 사용하지 않으므로 메모리 셀 efficiency를 극대화 할 수 있는 장점이 있다. 또한 기존의 common-plate 셀과는 달리 제안된 FRAM 구조는 데이터의 읽기 및 쓰기 동작 시 강유전체 커패시터에 V/sub DD/거 충분한 전압이 가해지므로 저 전압 동작에 제한이 없다. 아울러 제안된 FRAM 구조는 필요한 8 비트 데이터만 선택하는 column-path 회로를 사용하므로 메모리 array 전력소모를 최소화 할 수 있다. 끝으로 0.5-um, triple-well/1-polycide/2-metal 공정을 이용한 4-Mb FRAM 설계를 통해 GPPG 셀 FRAM architecture 실현 가능성을 확인하였다.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.1-8
• /
• 2019

Demand for plastic gears are increasing in many industries due to their low production cost, light weight, applicability without lubricant, corrosion resistance and high resilience. Despite these benefits, utilizing plastic gears is limited due to their poor material properties. In this work, DLC coating was applied to improve the tribological properties of polyamide66 gear. 0 V, 40 V, and 70 V of negative bias voltages were selected as a deposition parameter in DC magnetron sputtering system. Pin-on-disk experiment was performed in order to investigate the wear characteristics of the gears. The results of the pin-on-disk experiment showed that DLC coated polyamide66 with 40 V of negative bias voltage had the lowest friction coefficient value (0.134) and DLC coated PA66 with 0 V of negative bias voltage showed the best wear resistance ($9.83{\times}10^{-10}mm^3/N{\cdot}mm$) among all the specimens. Based on these results, durability tests were conducted for DLC coated polyamide66 gears with 0 V of negative bias voltage. The tests showed that the temperature of the uncoated polyamide66 gear increased to about $37^{\circ}C$ while the DLC coated gear saturated at about $25^{\circ}C$. Also, the power transmission efficiency of the DLC coated gear increased by about 6% compared to those without coating. Weight loss of the polyamide66 gears were reduced by about 73%.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1998년도 제16회 학술발표회 논문개요집
• /
• pp.137-137
• /
• 1998

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1326-1329
• /
• 1995

An influences of gap clearance, pressure and applied voltage shape on breakdown characteristics are investigated by using a rod-to-plane electrode in $SF_6$ gas. In case of D.C and A.C, a corona stabilization effect increases the breakdown voltage remarkably for lower pressure than 0.2MPa, whereas incase of negative D.C this effect exists independently of gas pressure. This suggests that an insulation optimization in a pratical apparatus is needed to prevent a corona appearance through the removal of local field enhancement.