• Fire Science and Engineering
• /
• v.10 no.1
• /
• pp.3-9
• /
• 1996

Electrostatic charge is generated in large scale or high speed processes dealing with materials with large resistance, or under complicated condition. Fire and explosion often occur due to electrostatic charge accumulated in flammable gases, vapor, liquids and powder. It is usually very difficult to verify the cause of accidents as well as the prevention. In this study, it is shown that the needle electrode needs the electrode gap from 1.8mm to 3.8mm, sphere electrode and plate electrodes need the electrode gap of 1.9mmfor the minimum ignition energy. The sphere electrode and the plate electrode requires 12.8mJ and 3.2mJ of minimum ignition energy respectively with the electrode gap of 1.1mm. The ignition voltage rises to very large value as the ground resistance increases.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.281-285
• /
• 1990

Our N.C. sewing machine is a device that acts sewing automatically in reference to N.C. data made by data input device. Our N.C. sewing mechine is composed of induction motor that has electric clutch and brake, step motor that drives x-y table. Sewing area of our machine is 170 mm * 100 mm, maximum sewing speed is about 2000 spm, maximum stitch length 6.2 mm. In actual sewing, synchronization between motion of needle up-down and motion of x-y table is a critical factor. In this paper, technology about synchronization will be profoundly discussed.

• Journal of ILASS-Korea
• /
• v.15 no.1
• /
• pp.8-16
• /
• 2010

This paper present the diesel spray characteristics at different injection system parameters in a HSDI diesel engine. The spray characteristics was calculated by the coupled simulation of fuel injection system model and three-dimensional KIVA-3V code with TAB spray model. The relevant injection parameters are accumulator volume, control chamber initial volume, control orifice diameter, needle valve diameter and nozzle chamber initial volume, etc. Parametric investigation with respect to twelve relevant injection parameters showed that there was a significant advantage in varying control chamber initial volume, control chamber orifice diameter, and nozzle chamber orifice diameter with respect to effect the SMD and fuel injection speed. Consequently, in order to design the fuel injection system for spray characteristics, it seems reasonable to suppose to be optimized the fuel injection system.

• 한국연소학회:학술대회논문집
• /
• 1998.10a
• /
• pp.103-110
• /
• 1998

This experiment is performed to investigate the effects of the emulsion on the flame temperature and soot formation in a diesel engine. The two-color method is used to measure the flame temperature for combustion of emulsified diesel in the Rapid Compression and Expansion Machine(RCEM). The concentration of soot is estimated via calculation of the KL factor. The solenoid valve, elecronic controller and needle lift sensor are used to control the exact injection timing and duration under various operating conditions. According to the results the soot concentration is reduced with the increasing W/O while the temperature reduced. The pressure data and the flame images captured by a high speed camera show that the ignition delay of emulsified diesel increase the duration of premixed combustion. The sizes of water drops are measured to be about 10${\mu}m$ by a microscope.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.566-569
• /
• 2008

Recently, the biolistic process is emerging as an effective needle-free drug delivery technique to transfer adequate concentrations of pharmacologic agents to soft living tissues with minimum side effects. We have started developing an effective method for delivering drug coated particles using laser ablation. A thin metal foil with deposited micro-particles on one side is irradiated with laser beam on the opposite side so that a shock wave is generated. This shock wave travels through the foil and is reflected, which causes and instantaneous deformation of the foil. Due to such a sudden deformation, the micro-particles are ejected at a very high speed. Here we present the experimental results of direct and confined laser ablation, which correspond to the initial stage of the whole experiment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.533-540
• /
• 2013

Prime movers in engine rooms inherently are much affected by the adjustment of their governors for the steady state and transient properties, consequently requiring that marine engineers shall be well familiar with the way to manage governor dials for normal operation. The hydro-mechanical governors basically have different control characteristics and adjustment parameters of stability from digital governors. The former include compensation mechanism using dash pot while the control algorithm of the latter is usually based on the PID action. This study is for configuring a simulation module to let trainees practice how to adjust dials for stability on hydraulic governors in the view that the practice by real governors and engines is time consuming and high cost for operation. The governor module includes the adjusting points such as speed set, speed droop, needle valve and compensation pointer with engine module of $2^{nd}$ order coupled. The results of simulation showed satisfactory responses as a training tool for the adjustment of control parameters.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.1
• /
• pp.6-14
• /
• 2011

The re-crystallization process for recovering granular crystalline gypsum from phospho-gypsum have proposed. The process consists of two stages; at the first stage, needle-like fine gypsum is recovered with under-product of 325 mesh wet screening after the speedy hydration of dehydrated phospho-gypsum, and at the second stage, granular crystalline gypsum is recovered with upper-product of 325 mesh wet screening after dehydration and re-crystallization of the needle-like fine gypsum in $Na_2SO_4$ solution. This paper is mainly focused on the influence of dehydration time, cooling speed of temperature and re-crystallization temperature on the recovery of granular crystalline gypsum. And the re-crystallization velocity of needle-like fine gypsum at room temperature and the variation of $Ca^{2+}$ concentration of gypsum slurry during over all re-crystallization process were also discussed.

• Journal of Biosystems Engineering
• /
• v.25 no.6
• /
• pp.463-470
• /
• 2000

For maximum seeding efficiency of a nozzle type seeder, the performance of the nozzle should be considered sufficiently. This study was carried out to investigate the optimum operating conditions of a seeder attached the vacuum nozzle which was modified syringe needle acting on the plug seedling tray and the seed plate. Such operating factors as the hole diameter of the nozzle (d), the distance from the nozzle tip to the bottom plate of seed hopper(D) the absorbing air pressure of the nozzle tip(P) the bounding height of seed from the vibrated bottom plate of seed hopper and the seeding speed were selected based on the weight of a grain of seed(W). The treated materials were pepper seed as the flat type, cucumber seed as the oval type and radish seed as the spherical type. The optimum operating conditions of the experimental seeder were revealed as follows: 1. The height of the seed bounding from the bottom plate of seed hopper and the distance from nozzle tip to bounded seed were 5 mm and 0.5 mm at all seeds. The hole diameter of the nozzle and the absorbing pressure for pepper seed, cucumber seed and radish seed was 0.45 mm, 0.65 mm. 0.65mm and 39.2 kPa, 88.3 kPa, 58.8 kPa, respectively. 2. The absorbing pressure P was represented as P=η.4W/$\pi$d$^2$ where η was 100. The seeding speed using a 128 cell tray was 2.4 cm/s which was same transfer as 2.5 trays per minute. 3. The maximum seeding rate in case of the pepper seed was 97% the cucumber seed was 95% and the radish seed was 100% under the optimum operating conditions of the seeder.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.2
• /
• pp.166-170
• /
• 2000

Amorphous calcium carbonate was prepared by wet chemical method and performed the control of their shape using crystalline calcium carbonate that prepared from oyster shell by the $CO_2$ gas blowing method. As a result, amorphous calcium carbonate was obtained by the dissolution process of crystalline calcium carbonate in the dil-HC1 solution, mixing of sodium carbonate solution, precipitation and filtering with high speed. And using the amorphous calcium carbonate of mud type, crystalline calcium carbonates with cubic, needle, spindle, spherical and plate shape were obtained in the temperature rang of 2~$85^{\circ}C$ and reaction time range of 5~60 minute.

• Journal of Biosystems Engineering
• /
• v.28 no.5
• /
• pp.395-402
• /
• 2003

Standard ginseng seedling, selected after one year's rearing in the seedling bed has been conventionally transplanted in Korea. Recently, the direct seeding areas have been increasing to product high quality ginsengs for red-ginseng processing. Reciprocating push-rod brush, holed-roller and vacuum suction seeders, planting with 30 ${\times}$ 30mm spacings and adjustable to the folds were designed and theirs performances were evaluated. The developed three types of seeders reliably performed at the success rate over 95% with less than 10% in slip rate, and could be used a seeder for the greater spacings by adjusting metering parts. The research concluded that the vacuum suction seeder was the most feasible and practical with the greatest metering success and the least slip among three type seeders of the reciprocating push-rod brush, holed-roller and vacuum suction seeders. The vacuum suction seeder holds a seed with each needle nozzle using the negative pressure created by a vacuum pump. The capacity was 24.5 times greater than a man power at the speed of 5 m/min.