• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.4
• /
• pp.105-111
• /
• 2019

In this paper, a performance analysis of waveguide broad-wall slot array antenna for millimeter-wave seeker in Ka-band was performed as using near-field measurement. The measurement of slot array antenna was conducted in both far-field and near-field. And the validation of near-field test in millimeter band was confirmed. It was confirmed that the beam pattern characteristics including beam width and side lobe level of the slot array antenna that performed the verification were the same. Differenced in the side lobe level of azimuth and elevation beam pattern were verified to be less than 1dB. Additionally, the new antenna aperture distribution was extracted as using back-projection method modifying the near-field data and then introduced the method conducting performance analysis of array antenna.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.2
• /
• pp.64-69
• /
• 2009

In this paper, we investigate field distribution and interference pattern in the exit pupil and in the focal region. Also, we compare with metal and dielectric substrate for near-field recording. To obtain field distribution, we use modified vector diffraction theory and Zernike Polynomials. Finally, we design and optimize refractive index and thickness of disk for near-field surface recording and cover-layer incident recording.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.4
• /
• pp.65-70
• /
• 2011

These days, printed electronics attract attention from electronics industry. In this paper, the fabrication of the fine patterns by Near Field Electro Spinning (NFES) was studied by using Ag ink on silicon wafer (substrate). Two types of ink, the high viscous ink Ag-200 and low viscous ink Ag-15, were used. The fine and uniform patterns were easily fabricated by using Ag-200 because jet breakup is less occurred in high viscosity solution. As increasing flow rate of solution, aspect ratio of Ag pattern decreased. And there was optimum applied voltage for fine pattern. In case of Ag-200, the optimum applied voltage was about 2.02KV. When pattern was fabricated by NFES, the pattern width and height were affected by many factors such as viscosity, flow rate of solution, applied voltage etc.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.1
• /
• pp.1-6
• /
• 1984

Calculation of the launch-condition dependent near field pattern, modal power distribution and far field pattern of the SGS mode scrambler by ray optical approch fits well with the experiment. These results were applied to explain how to establish the stable mode launching into the grated index multimode fiber under test by the SGS mode scrambler. The effective use of the 5G5 mode scrambler is found to restrict the launching NA as well as possible. This was also confirmed by experiment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.590-595
• /
• 2004

The shape and size variations of the nanopatterns produced on a positive photoresist using a near-field scanning optical microscope(NSOM) are investigated with respect to the process variables. A cantilever type nanoprobe having a 100nm aperture at the apex of the pyramidal tip is used with the NSOM and a He-Cd laser at a wavelength of 442nm as the illumination source. Patterning characteristics are examined for different laser beam power at the entrance side of the aperture( $P_{in}$ ), scan speed of the piezo stage(V), repeated scanning over the same pattern, and operation modes of the NSOM(DC and AC modes). The pattern size remained almost the same for equal linear energy density. Pattern size decreased for lower laser beam power and greater scan speed, leading to a minimum pattern width of around 50nm at $P_{in}$ =1.2$\mu$W and V=12$\mu$m/. Direct writing of an arbitrary pattern with a line width of about 150nm was demonstrated to verify the feasibility of this technique for nanomask fabrication. Application on high-density data storage using azopolymer is discussed at the end.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1155-1164
• /
• 2011

In this paper, we proposed the transmit beam measurement method of active phased array antenna, which is installed in Korea's first developed naval medium range radar, using near-field measurement facility. The pulse-mode high power characteristics of active phased array antenna's trasmit-beam make it difficult to measure with general near-field measurement facilities where low power continuous RF signals are used. Thus, in this paper, the measurement method of active phased array antenna's transmit beam in conjunction with the near-field measurement facility, which is suitable for the high-power transmit beam measurement, and PNA-X network analyzer(Agilent Technologies), which can support pulse-mode measurement, was proposed and measured by near-field measurement techniques. And the EIRP(Effective Isotropic Radiated Power), the transmit characteristic of active phased array antenna, was measured by the near field measurement techniques and compared to numerical estimation which was nearly equal with small difference of 0.1 dB.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.5 s.170
• /
• pp.80-86
• /
• 2005

Optical performance evaluation results and an interference fringe pattern analysis of alignment errors for an optical head of a near-field receding (NFR) system are presented. The focusing unit is an optical head of a NFR system and is composed of a solid immersion lens (SIL) and an objective lens (OL). Generally, the size of the focusing unit is smaller than that of the conventional optical recording head. Hence there are difficulties to assemble the small focusing unit precisely. We composed an evaluation system with an interferometer and evaluated some focusing unit samples aligned and assembled by manual and present the obtained results. Using the conventional optical tool, Code V, a tolerance analysis of the alignment error between the SIL and the objective lens and an interference pattern analysis for the assembly error are executed. Then, through an analysis of the simulation results, the conceptual auto-alignment methodology using a neural network approach is considered.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.487-488
• /
• 2012

• The Journal of the Korea Contents Association
• /
• v.6 no.2
• /
• pp.51-58
• /
• 2006

The enhancement of antenna near-field measurements is obtained using a general probe compensation equation based on the Lorentz reciprocity theorem and reciprocity notation. The probe compensation is an essential process of the near-field to far-field transformations. Applying the equation proposed in this paper to a planar scanning for a rectangular horn antenna shows that our near-field radiation pattern is similar to that of a far-field and our theory is very simple to use and suitable for most practical applications.

• Journal of Advanced Navigation Technology
• /
• v.27 no.5
• /
• pp.546-551
• /
• 2023

In this study, a beam steering measurement system was developed to perform functions such as far-field beam steering and near-field beam focusing for TX/RX modes in the near file of the AESA radar. The beam steering measurement system consists of a spherical near-field scanner, an antenna positioner, a near-field controller, a network analyzer, a radar control system, a verification radar, a simulated radio, and an AESA radar. Using the developed system, the characteristics of TX/RX patterns before and after installation of radome to AESA radar were measured, and the beam pattern was analyzed through conversion to far field-after near-field measurement.The boresight error of the radar antenna device was measured, and it was confirmed that the main lobes were formed the same before and after the simulated radar dome was mounted.