• Medical Lasers
• /
• 제8권2호
• /
• pp.74-79
• /
• 2019

Periorbital melasma is often refractory to treatment and highly associated with rebound hyperpigmentation or mottled hypopigmentation after laser treatment in Asian patients. In this report, we describe 2 patients with cluster-1 periorbital melasma and 1 patient with cluster-2 periorbital melasma who experienced remarkable clinical improvements after microwave-generated, atmospheric-pressure, non-thermal nitrogen plasma treatments. All patients exhibited limited clinical responses after combination treatments with topical bleaching agents, systemic oral tranexamic acid, and low-fluenced Q-switched neodymium (Nd):yttrium-aluminum-garnet (YAG) lasers. Low-energy nitrogen plasma treatment at 0.75 J elicited remarkable clinical improvement in the periorbital melasma lesions without post-laser therapy rebound hyperpigmentation and mottled hypopigmentation. We deemed that a single pass of nitrogen plasma treatment at 0.75 J induces mild microscopic thermal tissue coagulation and modification within the epidermis while preserving the integrity of the basement membrane in patients with periorbital melasma. Accordingly, nitrogen plasma-induced dermal tissue regeneration could play a role in the treatment of melasma lesions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.106-109
• /
• 2004

In this project, we have developed the eye-safe LRF system of 1.54 ${\mu}{\textrm}{m}$ wavelength using OPO. The maximum measured distance was 3.7km in outdoor experiment. We used Nd：YAG (1064nm) as a laser medium. It was applied BBO to construct the system. We also developed a time-counter for the range finder using a method of TOF (time of flight). The counter-clock used at the time counter was 320MHz making resolution within $\pm$1m. Start and stop signals were detected by two channel systems using PIN and APD. The LRF's repetition rate was 4 times per minute. The energy was measured to be over 9mJ. And, pulse-duration was 23ns. Resolution was $\pm$2m at the distance measurement using a target.

• 한국대기환경학회지
• /
• 제17권5호
• /
• pp.385-393
• /
• 2001

We have developed a Differential Absortion LIDAR (DIAL) method for the measurement of lower tropospheric ozone concentration. We used two laser beams from quadrupled Nd:YAG (266 nm) for the resonance wavelength and dye lasers (299.5 nm) for non -resonance wavelength. Aerosol extinction coefficients in the lower troposphere was computed by both Klett and Slope methods. To correct the SIN (Signal -Induced Noise) effect caused by photo detector, we subtracted a new-fitted baseline on the background part of a LIDAR signal, after the subtraction of the DC level. This is because SIN can be treated as an exponentially decaying tail. Using theme results, ozone profiles were obtained approximately 2km at daytime and 3km at nighttime. We compared the results derided by the Slope method with those measured by UV spectrometer. The computed results are in mostly good agreement with experimental results. In the measurement of the vertical layer, we observed the variation of the ozone profiles around the top mixed layer.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.7-12
• /
• 2007

To reveal the newly found liftoff height behavior of hydrogen jet, we have experimentally studied the stabilization mechanism of turbulent, lifted jet flames in a non-premixed condition. The objectives of the present research are to report the phenomenon of a liftoff height decreasing as increasing fuel velocity, to analyse the flame structure and behavior of the lifted jet, and to explain the mechanisms of flame stability in hydrogen turbulent non-premixed jet flames. The velocity of hydrogen was varied from 100 to 300m/s and a coaxial air velocity was fixed at 16m/s with a coflow air less than 0.1m/s. For the simultaneous measurement of velocity field and reaction zone. PIV and OH PLIF technique was used with two Nd:Yag lasers and CCD cameras. As results, it has been found that the stabilization of lifted hydrogen diffusion flames is related with a turbulent intensity, which means that combustion occurs where the local flow velocity is valanced with the turbulent flame propagation velocity.

• 전자공학회논문지D
• /
• 제34D권11호
• /
• pp.20-24
• /
• 1997

We have successfully fabricated high power (~20W) laser diode array, which are useful for pumping Nd:YAG lasers. The laser diode aray has 20 100.mu.m-wide cahnnels of which space was adjusted to 350.mu.m to improve thermal characteristics. And channel width is 100.mu.m. For an uncoated LD array, the output power of 15.66W has been obtained at 41A under quasi-CW operation, which results in about 0.42W/A slope efficiency. After aR(5%) and HR (95%) coatings on both facets, the output power was improved up to 21.18W at 40A under the same operation as above and the slope efficiency was 0.795W/A. On the other hand, by using a near field measurement system consisting of objective lens, eyepiece, CCD camera and image processing board, the typical near field patten of 1*20 LD array was observed.

• 한국공작기계학회논문집
• /
• 제12권6호
• /
• pp.14-21
• /
• 2003

With the increased use of lasers in industrial welding applications, techniques for monitoring and controlling these processes become increasingly important. It is very important that we understand the dynamic behaviors of the laser induced Plume in welding, because the laser induced plume has considerable effects on welding efficiency and the quality of materials. As the plume fluctuation was associated with keyhole instability, unstable vapor plume indicated the process was unstable and would result in poor welds. An Infrared Thermal-vision Camera can be utilized compensate for incurracies encountered in real-time monitoring during laser welding. We have results that instabilities of plume are closely related with hot cracking and defect of laser welding.

• Medical Lasers
• /
• 제10권1호
• /
• pp.52-54
• /
• 2021

There is growing interest in minimizing postoperative scarring after a thyroidectomy. Among the many treatment types, laser therapy, especially picosecond-domain laser therapy, is accepted as a standard method. In the present case, a patient with a pigmented, contracted scar was treated using the combination of a picosecond laser and ablative fractional (AF) CO₂ laser. After 15 sessions of 1,064-nm picosecond with micro lens array (MLA) and AF CO₂ laser application, the patient showed significant improvement in their pigmented lesions and scar contracture with no noticeable side effects for 16 months. These results suggest that a combination of picosecond laser with MLA and AF CO₂ laser can treat pigmented, contracted scars safely and effectively.

• 한국항공우주학회지
• /
• 제36권4호
• /
• pp.352-356
• /
• 2008

수소제트와 동축공기를 사용한 본 연구에서, 난류확산화염의 화염안정성 특징을 실험적으로 수행하였다. 목적은 연료속도 증가에 따라 감소하는 부상화염길이의 경향을 보고하고, 부상 메커니즘을 포함한 화염구조를 분석하는 것이다. 수소연료는 100에서 300 m/s 사이에서 조절되었으며, 이때 동축공기는 16 m/s 고정되고, 주위류는 0.1 m/s 이하로 유지되었다. 유동장과 연소장 동시측정을 위하여, 두 대의 Nd:Yag 레이저와 CCD 카메라를 이용하여 PIV와 OH PLIF 기법이 사용되었다. 결론적으로 난류화염전파속도는 난류강도에 비례하였으며, 제트 레이놀즈수의 0.017승에 비례하였다.

• 조명전기설비학회논문지
• /
• 제24권5호
• /
• pp.160-168
• /
• 2010

본 논문은 대기압 펄스 배리어 방전을 이용하여 NO 가스를 무해한 물질로 환원시키기 위하여 방전공간에서의 NO 분자의 생성 및 제거과정에 대하여 레이져 유기형광법을 이용하여 시 공간적인 밀도변화를 측정 및 분석하였다. 사용된 펄스 배리어 방전리액터는 진전속도가 $2.7{\times}10^6$[m/s] 인 1차 스트리머가 음극표면에 도착한 이후에 2차 스트리머가 양극 부근에 발생되었다. 그리고, 펄스 레이져에 의하여 NO 분자만을 효율적으로 상위준위로 여기시키기 위하여 Nd:Yag 및 염료 레이져를 복합하여 226[nm]의 자외광을 방전공간으로 도입하였으며, NO 분자만을 $A^2{\Sigma}^+{\leftarrow}X^2{\prod}$(0,0)으로 여기시키고, 여기된 분자들이 낮은 준위 $A^2{\Sigma}^+{\rightarrow}X^2{\prod}$(0,2), (0,3)로 복귀됨에 따라 방출되는 주요한 형광신호를 측정하였다. NO 분자의 시 공간적 변화 측정결과로부터 NO 가스를 효율적으로 제거하기 위해서는 산소농도를 가능한 2 [%]이하로 낮추고, 2차 스트리머 진전에 의해서 충분하게 방전공간에서 NO 환원반응을 유발할 수 있도록 제어하는 것이 필요하다고 판단된다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.561-569
• /
• 2002

Laser has been called a "Quantum Machine" because of its mechanism of generation since the development on July 7,1960.by T.H.Maiman. We can now use this machine as a tool for manufacturing in industries. At present, 45kW CO2 laser, 10kW Nd:YAG laser, 6kW LD pumped YAG laser and 4kW direct diode laser facilities are available for welding a heavy steel plate of 40mm in thickness and for cutting metals at high speed of 140m/min. Laser Materials Processing is no longer a scientific curiosity but a modern tool in industries. Lasers in manufacturing sector are currently used in welding, cutting, drilling, cladding, marking, cleaning, micro-machining and forming. Recently, high power laser diode, 10kW LD pumped YAG laser, 700W fiber laser and excimer laser have been developed in the industrialized countries. As a result of large numbers of research and developments, the modem laser materials processing has been realized and used in all kinds of industries now. In the present paper, metallurgical studies on laser materials processing such as porosity formation, hot cracking and the joint performances of steels and aluminum alloys and dissimilar joint are discussed after the introduction of laser facilities and laser applications in industries such as automotive industry, electronics industry, and steel making industry. The wave towards the use of laser materials processing and its penetration into many industries has started in many countries now. Especially, development of high power/quality diode laser will be accelerate the introduction of this magnificent tool, because of the high efficiency of about 50%, long life time and compact.