• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.761-768
• /
• 2000

In order to investigate how the fatigue damage effects on the critical properties of superconductor, a fatigue test at room temperature and an Ic measurement test at 4.2K were carried out in this study, respectively, using a 9 strand Cu-Ni/NbTi/Cu composite cable. Through the fatigue test of a 9 strand Cu-NUNbTi/Cu composite cable, a conventional S-N curve was plotted even though there was a possibility of fretting among strands. It was found that the maximum stress corresponding to the inflection point on the S-N curve obtained was nearly the same value as the yielding strength of cable obtained from the static tensile test. However, the effect of cabling in multi-strands superconducting cable on the fatigue strength was not noticeable. The critical current(Ic) measurement was carried out at 4.2K in a NbTi strand out of the fatigued cable. It showed a degradation of lc at high stress amplitude regions over 380NTa, and the degradation became significant as the applied stress amplitude increased.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.207-207
• /
• 2003

최근 광촉매 재료로 각광받고 있는 TiO$_2$는 band gap 에너지가 3.0-3.2eV로 자외선 영역과 일부 가시광선 영역에서 활성을 갖는 것으로 알려져 있다. 따라서 용액 중에 결정화 및 안정화 되어있는 TiO$_2$의 band gap 에너지를 낮춘다면 가시광 영역의 광반응을 얻을 수 있다. 이에 본 연구는 G. Sato등이 제안한 방법으로 TiO$_2$ sol을 제조할 때 band gap 에너지를 낮추고자 천이 금속원소를 첨가하여 복합 및 담지된 TiO$_2$계 복합 sol을 합성하고자 하였다 출발원료는 TiC1$_4$를 가수분해하여 제조한 TiOCl$_2$에 천이금속원소인 V, Cr, Fe, Ni, Nb 등의 chloride 화합물을 첨가하여 중화 및 세척과정을 거친 후, 과산화수소수에 용해하여 전구체 용액인 titania peroxo용액을 제조하였다 제조된 전구체 용액은 온도와 시간을 변수로 각각 열처리하여 TiO$_2$계 복합 sol을 합성하였다. 제조된 시편은 X-선 회절 분석, 투과전자현미경, particle size analyzer, ζ-potential analyzer 및 UV-VIS Spectrometer 통을 이용하여 천이금속 첨가에 따른 TiO$_2$계 복합 sol의 형성과정과 특성변화를 관찰하였다.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.1
• /
• pp.17-25
• /
• 1993

The Cu - $Nb_3Sn$ composites wire as a superconducting material was prepared by in situ method as follow: Cu - 15wt.% Nb alloys which were melted in a high -frequency induction furnace and casted in bar were cold-worked up to the final diameter of 0.24 mm, electroplated with Sn, pre-treated in two steps and then diffused at $550{\sim}650^{\circ}C$ for 24 ~ 96 hrs. The overall $J_c$ and $T_c$ of the specimens were measured by the four point-probe method at 10 K in the magnetic field of 0 Tesla. The overall $J_c$ of the composites wire which diffused at $550^{\circ}C$ after pre-treating in two steps were generally higher than those of the wire at either $600^{\circ}C$ or $650^{\circ}C$. For the specimens diffused at $550^{\circ}C$, the overall $J_c$ were increased until 72 hrs. of diffusion time and then decreased. However, in case of diffusion at $600^{\circ}C$ and $650^{\circ}C$, the overall $J_c$ were gradually decreased from the beginning. The maximum overall $J_c$ obtained in this experiment was $1.3{\times}10^4\;A/cm^2$, which was measured for the specimen diffused at $550^{\circ}C$ for 72 hrs. When the specimens were diffused at $550^{\circ}C$ for 72 hrs, after pre-treating, the measured critical temperature, $T_c$ was 16.19 K. Similar $T_c$ value were obtained in other specimens regardless of diffusion time and temperature.