• Journal of Sensor Science and Technology
• /
• v.13 no.2
• /
• pp.152-156
• /
• 2004

The dielectric and piezoelectric properties of 0.36Pb($Sc_{1/2}Nb_{1/2}$)$O_{3}$-0.25Pb($Ni_{1/3}Nb_{2/3}$)$O_{3}$-0.39Pb$TiO_{3}$ (hereafter PSNNT) at the morphotropic phase boundary (MPB) composition were investigated with $0{\sim}2.5$ mot% $MnO_{2}$ doping. Bulk density, dielectric loss and tetragonality of crystal structure were all improved with increasing $MnO_{2}$ additive content. With increasing $MnO_{2}$ additive content, the electromechanical coupling factor and quality factor were also increased: Electromechanical coupling $k_{p}$ and quality factor $Q_{m}$ at 2.0 mol% $MnO_{2}$ doping with were showed highest values of 55.6 % and 252, respectively.

• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.20-25
• /
• 1997

In this study, piezoelectric actuator samples were fabricated using 0.375PMN-0.37OPT-0.255PZ system ceramics with Barium substitution and the strain properties of them were investigated. Dielectric constant of the specimens increased with the increase of Ba content up to 5mol% and decreased with futher addition of Ba. The largest piezoelectric coefficient and electromechanical coupling coefficient were observed at the sintering temperature of 1250'C and Barium content of 5mol%. The characteristics of strain hysteresis was found largely with varing the sintering temperature on the single round type, and the strain is proportional to piezoelectric coefficient.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.118-119
• /
• 2006

The development of Fe-based metal matrix composites (MMCs) with high content of hard phase has been approached by combining the use of advanced powder metallurgy techniques like high-energy milling (HEM), cold isostatic pressing (CIP) and vacuum sinterings. A 30% vol. of NbC particles was mixed with Fe powder by HEM in a planetary mill during 10h, characteristing the powder by the observation of morphology and microstructure by scanning electron microscopy (SEM). After of sintering process the variation of density, hardness,carbon content and the microstructural changes observed, permits to find the optimal conditions of processing. Afterwards, a heat treatment study was performed to study the hardenability of the composite.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.251-256
• /
• 2012

Etherification of n-butanol to di-n-Butyl Ether was carried out over Keggin $H_{3+x}PW_{12-x}Nb_xO_{40}$ (x=0, 1, 2, 3) and $H_{6+x}P_2W_{18-x}Nb_xO_{62}$ (x=0, 1, 2, 3) Wells-Dawson heteropolyacid catalysts. Niobium-substituted Keggin and Wells-Dawson heteropolyacid catalysts with different niobium content were prepared. Successful preparation of the catalysts was confirmed by FT-IR, ICP-AES, and $^{31}P$ NMR analyses. Their acid properties were determined by $NH_3$-TPD (Temperature-Programmed Desorption) measurements. Heteropolyacid catalysts showed different acid properties depending on niobium content in both series. The correlation between acid properties of heteropolyacid catalysts and catalytic activity was then established. Acidity of Keggin and Wells-Dawson heteropolyacid catalysts decreased with increasing niobium content, and conversion of n-butanol and yield for di-n-butyl ether increased with increasing acidity of the catalysts, regardless of the identity of heteropolyacid catalysts (without heteropolyacid structural sensitivity). Thus, acidity of heteropolyacid catalysts served as an important factor determining the catalytic performance in the etherification of n-butanol to di-n-Butyl Ether.

• Journal of the Korean Ceramic Society
• /
• v.35 no.10
• /
• pp.1040-1048
• /
• 1998

Ferroelectric properties of{{{{ { { { {SrBi }_{2 }Ta }_{2-x }Nb }_{x }O }_{9 } }} (SBIN) thin films were affected by the amount of Bi content in SBTN. The addition of Bi into the SBTN films could be accomplished by heat treating SBTN/Bi2O3/SBTN het-erostructures fabricated by r.f. magnetron sputtering method. The variation of Bi content was controlled by changing the thickness of the sandwiched Bi2O3 in SBTN/Bi2O3/SBTN heterostructure from 50 to 400$\AA$. As changing the thickness of the sandwiched Bi2O3 in Bi2O3 films was increased from 0 to 100$\AA$ the grain grew faster and the ferroelectric pro-perties were improved. On the other hand when the thickness of Bi2O3 films was thicker than 150$\AA$ the fer-roelectric properties were deteriorated Especially for SBTN thin films inserted by 400$\AA$ Bi2O3 layer a Bi2Phase appeared as a second phase resulting in poor ferroelectric properties. The maximum remanent po-larization (2Pr) and coercive field(Ec) were obtained for the SBTN/Bi2O3/(100$\AA$)/SBTN thin films. In this case 2Pr and Ec were 14.75 $\mu$C/cm2 and 53.4kV/cm at an applied voltage of 3V respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.14-16
• /
• 1993

In this Paper. Pb($Zn_{x}Nb_{1-x}$)$O_3$ ceramics were fabricated by the mixed oxide method. The sintering temperature and time were 1,000($^{\circ}C$). 1(hr). respectively. According to the contents of $ZnO_2$, the depression of pyrochlore phase and its effects were studied. As the results of the XRD patterns and SEM. the pyrochlore and second phase were increased with increasing the $ZnO_2$. As the $ZnO_2$ content was increased. density was decreased.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1232-1233
• /
• 2006

To co-fire with commercial LTCC (Low Temperature Co-fired Ceramic) materials at $850^{\circ}C{\sim}880^{\circ}C$, different contents of $B_2O_3$ were added to the $Bi_2O_3-ZnO-Nb_2O_5$ (BZN) ceramics. According to the test results, the cubic phase of BZN was transformed into orthorhombic in all the test materials. $BiNbO_4$ phase was formed in test materials with $2{\sim}5wt%$ of $B_2O_3$ addition. The phase transformation of cubic BZN was controlled during the synthesis process with excess ZnO content. The Cubic and orthorhombic phases of BZN could coexist and be sintered densely at $850^{\circ}C/2hr$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.405-408
• /
• 1997

The microwave dielectric properties of CuO and CdO addition of BiNbO$_4$ceramics were investigated. As the content of CdO increased, sintered density and quality factor is decreased. With increase in sintering temperature, the dielectric constant and quality factor is increased. In case of specimen sintered at 96$0^{\circ}C$ with 0.03 wt% CuO and CdO, the microwave dielectric properties obtained were dielectric constant of 41.2, quality factor (Q$\times$f) of 6, 500, temperature coefficient of resonant frequency of ppm/$^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.360-364
• /
• 2003

$Sr_{l}$ $\pm$x/$Bi_{2}$ $\pm$y/$Ta_2$ $O_{9}$ and $Sr_{l}$ $\pm$$Bi_{x}$ $2\pm$y$Nb_2$$O_{9}$ ceramics were prepared by a solid state reaction method. X-ray diffraction analysis indicated that single-phase of Bi-layered perovskite was obtained. According to Sr/Bi content ratio, Curie temperature( $T_{c}$), electromechanical factor($K_{p}$ ) and mechanical quality factor($Q_{m}$ ) were measured. The Curie temperature of SBN(SBT) rose from $414^{\circ}C$(314$^{\circ}C$) to $494^{\circ}C$(426$^{\circ}C$) when Sr/Bi content ratio was increased. In the case of Sr/Bi content ratio = 0.55/2.3, the maximum value of the mechanical quality factor $Q_{m}$ of SBT and SBN were obtained 3320 and 1010, respectively.

• Korean Journal of Metals and Materials
• /
• v.47 no.4
• /
• pp.209-216
• /
• 2009

It was evaluated that the microstructural and mechanical properties of Ta-bearing 9Cr-0.5Mo-2W ferritic/martensitic experimental steels. All the experimental steels showed the tempered martensitic microstructures, and $M_{23}C_6$ carbides, whose sizes were ranged from 200 to 300 nm, were easily observed at both boundaries of the prior austenite grain and the martensite lath. In addition, a relatively large Nb-rich MX carbonitrides were intermittently detected at the prior austenite grain boundaries, whereas a lot of Vrich MX carbonitrides, whose mean diameter was less than 50 nm, were observed randomly at both boundaries. Ta was mainly incorporated into the V-rich MX carbonitrides rather than the Nb-rich ones and their content was spanned from 5 to 20 at.%. Ta contents within the MX precipitates also increased as the content of Ta increased. Because the Ta addition into the steels would be attributed to the precipitation strengthening, solid solution strengthening and lath width reduction, it was shown that the mechanical properties, including hardness, tensile strength and creep rate of the 9%Cr-0.5Mo-2W steels were improved by the increase of Ta content. Especially, 9Cr-0.5Mo-2W-0.3V-0.05Nb-0.14Ta steel was revealed to be relatively excellent in the application for the SFR fuel cladding.