• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국해양학회지:바다
• /
• 제5권3호
• /
• pp.195-207
• /
• 2000

우리나라 갯벌과 농지내 유 ${\cdot}$ 무기 원소의 거동을 이해하기 위해 제한된 환경의 실험실 수조에서 예비실험을 수행하였다. 총 6개의 아크릴 투명 수조에 갯벌 퇴적물 3종 SW1&2(anoxic, silty mud), SW3&4(anoxic, mud), SW5&6(suboxic, mud)과 농지 토양 3종 FW1&2(벼 포기 포함), FW3&4(벼 포기 제외), FW5&6(간척 농지,펴 포기 제외)을 채운 후 오염물질(구리, 비소, 카드뮴, 크롬, 납, 수은, Glucose+Glutamic acid)이 주입된 해수와 담수를 각각 SW 및 FW수조에 넣고, 2주일에 걸쳐 상층수 및 표층 퇴적물/토양을 채취 ${\cdot}$ 분석하였다. 분석 결과 FW와 SW상층수 중 질산염 이온의 농도는 각각 700${\sim}$800 ${\mu}$M, 2${\sim}$5 ${\mu}$M로 FW에서 현저히 높았고, 인산염 이온의 농도는 각각 3${\sim}$4 ${\mu}$M, 1${\sim}$2 ${\mu}$M(SW1 제외)로 FW에서 약간 높았다. 특이하게 SW1에서 인산염 이온은 시간이 지남에 따라 수 십 ${\mu}$M에 이르는 높은 농도로 증가하였다. 한편, 표층 퇴적물/토양 중 박테리아 세포 수는 FW1&3에서 평균 2.5${\times}$10$^9$cells/g dry sediment으로 SW의 평균 3.0${\times}$10$^8$cells/g dry sediment 보다 약 10배가 높았다. FW5 토양 중 박테리아 세포 수(3.5${\times}$10$^8$cells/g dry sediment)는 SW 퇴적물 중 숫자와 유사하였다. SW 퇴적물 중 MUF-Phosphate 활성도는 100-200 nM/ml/hr이지만 FW5&6을 제외한 FW 토양에서는 약 2,000 nM/ml/hr로 현저히 크게 나타났다. ${\beta}$-D-Cellobiose, ${\alpha}$-D-Glucose, 그리고 ${\beta}$-D-Glucos의 활성도 또한 FW 퇴적물에서 큰 값을 보였다. 그러나 FW5&6 토양 중 효소활성도는 SW 퇴적물에서의 값과 유사했다. 수조 상층수 중 Cu, Cd, As 농도는 모든 FW, SW수조에서 시간이 지남에 따라 일관성 있게 감소하였고, 제거속도는 Cu가 다른 원소에 비해 빨랐다. 제거속도는 FW 3개 수조 중 FW5&6에서 세 원소 모두 가장 느렸고, SW 3개 수조 중에서는 SW1&2에서 가장 빨랐다. SW와 FW간 제거속도 차이는 세 원소 모두 명확치 않았다 Cr은 FW에서 전반적으로 감소하는 경향을 보였지만 SW에서는 실험 초기에 감소하다 24시간 이후에는 증가 후 일정한 양상을 보였다. Pb은 FW에서 전반적으로 감소했지만 SW에서는 초기에 급격히 증가 후 다시 급격히 감소하는 양상을 보였다 Pb 또한 Cu, Cd, As와 마찬가지로 SW1&2에서 제거속도가 가장 빠르게 나타났다. FW 상층수 중 Hg는 시간에 따라 급격히 감소했고, 제거속도는 Fw5&6에서 가장 느렸다. 이러한 결과에 근거할 때 벼가 자라고 있고 이분해성 유기물이 풍부한 FW1&2, FW3&4 토양과 상층수에서는 유기물의 분해 활동이 활발하였지만, 벼가 경작되지 않는 FW5&6과 SW 에서는 유기물이 상대적으로 결핍되어 유기물의 분해활동이 적었을 것으로 판단된다. 한편, 수조에 인위적으로 유기물을 첨가한 경우 박테리아 세포수는 SW1에서 164시간 동안 4배 증가하였으나 SW3과 SW5에서는 각각 2.7배, 1.5배 그리고 FW1&3&5의 경우 각각 약 2배, 1.7배, 0.6배 정도만 증가하였다. Cu, Cd, As등 친 유기성 원소들의 시간에 따른 농도 감소 그리고 이들 원소(Hg 포함) 농도 감소 속도가 유기물이 적은 FW5&6에서 상대적으로 느리게 나타난 결과 등은 이들 금속들이 부유 입자 표면의 유기물과 결합 ${\cdot}$ 침적되어 퇴적물로 제거되었기 때문에 나타난 결과로 생각된다. 한편, SW1&2에서 이들 원소의 제거 속도가 빨랐고 인산염 이온의 농도가크게 증가했던 원인은 SW3&4에 비해 상대적으로 공극이 큰 퇴적물로 채워진 SW1&2 퇴적물의 공극수 중 황화수소, 인산염 이온 등이 퇴적물 상층수로 쉽게 확산 ${\cdot}$ 공급되었고, 그 결과 Cu, Cd, As 등 금속 이온이 황화수소 이온과 결합 ${\cdot}$ 제거된 까닭으로 생각된다. 종합적으로 수조 상층수중 유 ${\cdot}$ 무기 원소의 거동은 주로 입자 표면의 유기물과 퇴적물/토양에서 공급된 황화물에 의해 조절된 것으로 생각된다.

• Journal of Plant Biology
• /
• 제3권1호
• /
• pp.1-15
• /
• 1960

P. japonica가 분류학에서 말하는거와 같이 리웅이주가 않이고 이형호장물이라는 것을 훌견하고 수년간 이 식물의 장주화개체, 단주화개체간의 화기의 형태, 수정력, 화분관의 행동 및 L, S주의 화분의 임, 불임등을 조사해 보았드니 이 식물은 이형수장물중에서도 L, S주간의 분화가 가장 심하게 되어 있어 일부기관이나 기능은 웅웅이주와 같이 변해버린 특수한 이형수장물이라는 것이 명백히 되었고 이 장물은 장물조포체세대의 성의 분화가 생기는데 이형현상을 거쳐서 되는 경우도 있지 않나 하는 것을 가정케하는 한 증거가 될수 있다고 생각된다. 또한 여뀌과의 다른 이형예장물인 F. esculentum이나 P. senticosa와 비교해 보면 이 장물이 가장 L, S 주간의 분화가 심하고 F. esculentum은 중간, P. senticosa는 가장 미분화상태에 있어 삼종외 여뀌과 이형예장물간에 그 분화의 정도에 gradation이 생겨 있다. 이제 실험결과릎 요약하면 다음과 같다. 1) P. japonica는 화주장, 화사장, 등의 제일차의 형태적 차이뿐만 않이라 제이차적 형이도 대단히 심한 Dimorphism을 나타내고 있다. 2) L, S주의 화기의 차이는 동과의 타이형예작물에 비해 극경호 분화되어 있다. 3) L, S주의 웅예를 보면 S주는 대단히 발달되어 있는 반면에 L주의 웅예는 애예된것 같은 느낌을 주고 있다. 4) 적법수분에 의하면 L, S주가 다 결실이 잘 되지만 불적법수분에서는 수정결실이 전혀 안된다. 수정생리상으로도 뚜렷한 이형예작물이다. 5) 자가가임의 성질 또는 동형화간의 수정력은 완전히 상실하고 있다. 여뀌과의 타이형예작물과는 이 점에 차이가 심하다. 6) 자연상태하에 있어서는 S주는 결실이 거이 안되어 마치 \ulcorner주와와 같은 외관을 나태내고 있다. 7) 인공수분에서는 $L{\times}S$나 $S{\times}L$ 주 수정결실이 다 되어 S주의 행동은 자연상태하에서 와는 대단히 상이하다. 8) L주에 비해 S주는 수정후 용과가 더 심하다. 9) 화분관의 행동은 수정력과 완전히 일치된다. 즉 L-selfing, $L{\times}L$, S-selfing, $S{\times}S$등의 부적법 수분에서는 화분관은 화주의 미중에서 정지되지만 $L{\times}S$, $S{\times}L$,에서는 수분 약 40-50분 후이면 화분관은 자방까지 도달된다. 10) S주는 웅본으로 오인되어 있지만 인위적법수분을 하면 수정력이나 화분관의 행동은 L주에서와 동일하다. 11) S화분은 완전하지만 L화분은 약 70%가 내용공허한 Adortive pollen 이다. 12) L화분중 나머지 30%도 S화분에 비해서 염색도가 낮은것이 많고 S화분 같이 농염되는 것은 극히 소수이다. 13) 본장물은 분화가 고도로 진행된 전형적인 이형예작물이여 마치 Dimorphism 에서 Dioecious 에로 이행되는 수가 있다는 것을 표시하는 증거가 되는 것 같다.

• 미술자료
• /
• 제96권
• /
• pp.155-180
• /
• 2019

용주사 <삼세불회도>는 유교적 이념과 불교적 이념, 궁중화원 양식과 산문화승 양식, 고유한 전통화법과 외래적 서양화법 같은 다양한 이원적 요소들이 창조적으로 융합되어 이룩된 기념비적 걸작으로서 조선 후기의 회화 발달과 혁신을 상징적으로 보여주는 대표적 작품의 하나이다. 그러나 화기(畫記)가 없기 때문에 현존 <삼세불회도>의 제작시기와 작가를 비정하고 양식 특징을 분석하는 문제를 놓고 연구자마다 견해 차이가 심해 지난 50여 년 간 논쟁이 끊이지 않음으로써 회화사적 의미와 가치가 제대로 인식되지 못하고 있는 실정이다. 현존 <삼세불회도>의 제작시기를 추정하는 문제는 모든 논의의 기본적 출발점이 되기 때문에 특히 중요한 문제이다. 그러나 일반적인 불화와 달리 화기(畫記)가 없고, 작가에 대한 기록이 문헌마다 다르며, 화승들의 전통적인 불화 양식과 화원들의 혁신적인 서양화법이 혼재되어 있어 작가와 양식을 일치시켜 이해하는 문제가 쉽지 않기 때문에 제작시기를 추정하는 문제는 특히 논란이 많은 쟁점 중의 하나이다. 그런데 현존 <삼세불회도>는 일반적인 불화와 달리 수미단 중앙에 왕실(王室) 존위(尊位)의 축원문(祝願文)을 써놓아 주목되며, 애초에 썼던 "주상전하(主上殿下), 왕비전하(王妃殿下), 세자전하(世子邸下)"의 삼전(三殿) 축원문을 지우고 '자궁저하(慈宮邸下)'를 '왕비전하(王妃殿下)' 앞에 추가해서 고쳐 써넣어 더욱 주목된다. 따라서 이 축원문은 현존 삼세불회도의 제작시기를 추정할 수 있는 가장 중요한 객관적 단서의 하나이다. 그리하여 최근에 새롭게 제시된 19세기 후반 제작설은 1790년의 용주사 창건 당시에는 순조(純祖)가 '원자(元子)' 신분이었고 1800년 1월 1일에야 '세자(世子)'로 책봉되었기 때문에 '세자(世子)'라는 존호가 쓰여있는 현존 <삼세불회도>의 축원문은 세자 책봉 이후에 쓰여진 것으로 보아야 하며, 형식과 도상이 19세기 후반기 화승들이 그린 청룡사나 봉은사의 <삼세불회도>와 유사하고 서양화법은 후대에 개채된 것일 가능성이 많기 때문에 현존 <삼세불회도>는 19세기 후반기의 화승에 의해 그려진 것으로 보아야 한다고 하였다. 그러나 19세기 후반 불화(佛畫) 화기(畫記)의 축원문을 광범위하게 조사해보면, 불화 제작 시점에 왕실에 실존한 인물의 신분(身分)과 생년(生年), 성씨(姓氏)까지 구체적으로 쓰는 것이 통례였기 때문에 19세기 후반에는 용주사 <삼세불회도>의 축원문처럼 수십 년 전에 승하한 사람들을 생전의 존호(尊號)로 고쳐 쓸 수 없다는 것을 알 수 있다. 이에 반해 1790년 전후에는 원자(元子)나 세자(世子)의 유무(有無)와 무관하게 의례적으로 "주상전하(主上殿下), 왕비전하(王妃殿下), 세자저하(世子邸下)"의 삼전(三殿) 축원문을 쓰는 것이 관례였기 때문에 현존 <삼세불회도>의 축원문에 '세자저하(世子邸下)'의 존호가 쓰여있는 것은 오히려 당연한 것임을 알 수 있다. 그리고 일반적인 왕실 위계와 달리 '자궁저하(慈宮邸下)'가 '왕비전하(王妃殿下)'보다 앞에 쓰여있는데, 이는 사도세자(思悼世子)의 비극으로 인한 정조와 혜경궁(자궁(慈宮)), 왕비 세 사람의 특수한 관계로 인해 정조가 혜경궁의 왕실 위상을 왕비 앞에 오도록 하여 정조대에만 사용된 특별한 왕실 전례였기 때문에 현존하는 삼세불회도의 축원문은 정조대에 개서(改書)된 것임을 알 수 있다. 또한 애초에는 당시의 일반적인 불화 축원문처럼 의례적인 삼전(三殿) 축원문을 썼다가 이를 지우고 다시 '자궁저하(慈宮邸下)'라는 특별한 존호를 넣어 개서(改書)하는 매우 특별한 일이 일어났는데, 이는 현륭원(顯隆園)의 재궁(齋宮현륭인 용주사의 가장 중요한 주인공이 사도세자의 아들인 정조와 부인인 혜경궁(惠慶宮)(자궁(慈宮))임에도 불구하고 축원문에 의뢰적인 삼전(三殿)만 쓰여있고 혜경궁이 빠져있는 것을 보고 정조가 지시하여 개서(改書)했던 것이라고 생각된다. 그리고 이 개서(改書)는 정조가 현륭원과 용주사가 준공된 뒤 처음으로 현륭원에 원행(園幸)하여 원소(園所)를 두루 돌아보고 돌아오는 길에 잠시 용주사에 들러 <삼세불회도>를 처음이자 마지막으로 친견했던 1791년 1월 17일에 정조가 지시하여 이루어진 것이라고 믿어진다. 따라서 이와 같이 특수한 내용과 형태로 이루어진 축원문은 현존 <삼세불회도>가 1790년의 창건 당시에 그려진 원본 진작임을 말해주는 가장 확실한 객관적 증거라고 할 수 있다.

• 심성연구
• /
• 제37권2호
• /
• pp.184-254
• /
• 2022

본 논문을 통해 한국 민담 '주인집을 망하게 한 하인'의 심리학적 의미를 고찰하였다. 민담 속 주인과 하인의 대립은 보편적인 인간 정신의 문제로, 경화된 기존의 집단적 의식과 이를 보상하고 갱신하려는 새로운 의식의 대립으로 볼 수 있다. 다른 각도에서 설명해보자면 인간의 정신적인 측면과 본능적인 측면 사이의 혹은 의식과 무의식 사이의 대립이며, 자아와 그림자 사이의 대립이라고도 할 수 있다. 민담 속 주인은 애먹이는 막내 하인을 없애버리려 여러 차례 시도하지만, 하인은 꾀와 속임수를 써서 주인으로부터 음식과 말(馬), 막내 누이, 전 재산, 마침내 목숨까지 빼앗아 버리고, 이야기는 막내 하인과 막내 누이의 혼인 생활로 끝을 맺는다. 주인이 죽고 하인이 새로운 주인이 되는 대극반전(enantiodromia)은 낡은 집단적 의식이 파괴되고 집단적 무의식으로부터 올라온 새로운 의식이 지배적 위치에 서게 되는 것으로, 개인의 심리적 상황에서는 기존의 자아의 태도가 해소되고 새로운 태도로 변환되는 것으로 이해해볼 수 있다. 이야기의 중간 과정에서 하인은 그를 죽이려고 주인이 써준 등편지를 순박한 사람들을 이용해 새롭게 바꿔 써서 막내 누이와 혼인한다. 이 모습은 집단적 의식의 도덕관념에서는 부정적으로 이해될 수 있으나, 아낙네, 꿀장수, 배고픈 중으로 상징되는 조선 시대 집단적 의식에서 무시되어오던 정신요소를 통합하는 과정으로 볼 수 있다. 하인으로 대변되는 새로운 의식성은 기존의 틀에 구속받지 않는 트릭스터적 특성을 갖기에 집단적 의식에서 무시되어온 정신적 내용을 통합하여 조선 후기 집단적 의식에 대한 보상과 대안으로서 제시하는 요소라고 할 수 있다. 주인은 다시 하인을 죽이려고 하인을 가죽 부대에 넣어 나무에 매다는데, 가죽 부대 속에 들어가 매달렸더니 눈을 떴다는 하인의 속임수에 넘어간 소경이 대신 매달려 죽고 하인은 달아나게 된다. 주인과 하인의 대극 문제가 마침내 나무로 상징되는 전체 정신(Self)에 맡겨지자 소경이 제거되는 것은 트릭스터에 포함되어있는 맹목성, 어리석음, 탐욕적 요소를 구분하고 정화하려는 자기(Self)의 의도로 이해해볼 수 있다. 이런 과정들을 거쳐 집단적 의식의 새로운 변화 혹은 새로운 자아의 태도를 상징하는 하인은 기존의 문제들을 해결하고 주인의 자리에 서게 된다. 그러나 꾀 많은 하인의 활약상을 들으며 청중들은 유쾌함과 해방감을 느끼는 한편, 소경이 대신 죽고 주인집 식구가 몰살되고 하인이 주인이 되는 부분에서는 하인의 위험성과 통제 불가능에 대한 우려와 두려움의 감정을 경험하기도 한다. 해외 유화들에 등장하는 트릭스터들 역시 철저히 이기적이고 오직 욕구를 채우고 위험에서 빠져나가기 위해 무고한 존재들을 속이거나 죽게 만드는데, 이들 트릭스터를 처단하거나 교화하려는 노력은 허사로 돌아가고 그들은 달아나버린다. 그러므로 본 민담 역시 이런 원형적 그림자가 매우 위험하다는 것, 그리고 의식이 통제하거나 의식에 동화될 수 없다는 것을 알게 해주고, 그것을 외경하고 관조하도록 하는 목적 의미도 있다고 볼 수 있다. 트릭스터는 기존의 구조와 질서가 경화되었을 때 보상작용으로서 무의식으로부터 올라오는 재생시키는(revivifying) 자연 에너지의 비합리적 발현 양상이다. 그 현상은 기존의 집단적 정신의 입장에서는 파괴적이고 비도덕적일 수 있으나, 도덕적으로 규정할 수 없는 보다 근원적 정신인 집단적 무의식의 기능이라고 보아야 한다. 트릭스터 원형상으로 볼 수 있는 하인은 변환을 가져오는 존재로 파괴성과 창조성이라는 양면성과 모순성을 지니고 있다. 본 민담의 유화들의 결말은 여러 갈래인데 이는 트릭스터의 양면성으로 인해 청중의 마음 반응이 그만큼 다양하다는 것을 반영하며, 트릭스터 문제에 대한 무의식의 다양한 반응을 제시하는 것이기도 하다. 또한 트릭스터란 그만큼 결론이 안 나고 논란을 일으키는 모순덩어리 존재로 의식적 합리적 태도로 통제할 수 없다는 것, 우리 안의 트릭스터 원형에 대해 진지하게 관조할 수 있을 뿐이라는 것을 보여준다.

• 헤리티지:역사와 과학
• /
• 제44권4호
• /
• pp.172-205
• /
• 2011

본 연구는 종합적인 현황 조사 분석을 통해 국내 돌바둑판의 위치 및 형태 그리고 입지 유형을 파악하는 한편 주변 경물과 각자 그리고 인근의 전래지명과의 관련성 분석과 해석을 통해 암각바둑판의 본질적 특성 및 장소적 의미 그리고 문화재로서의 가치 등을 파악하고자 하였다. 바둑판에 나타난 '네모난 바둑판과 둥근 바둑돌'의 천원지방적(天圓地方的) 형상, 흑백 바둑돌로 표상되는 음양조화 그리고 하늘 회전을 표현한 361로 등은 '우주적 질서가 투사(投射)된 상징체'이다. 또한 영원성을 바탕으로 바둑 삼매경에 빠진 '귤중지락(橘中之樂)'과 '상산사호(商山四皓)' 그리고 '난가(爛柯)' 모티프는 속세를 벗어난 망우청락(忘憂淸樂)의 '위기선미(圍棋仙味)'를 통해 '인생과 자연'의 관계를 시공간적으로 일치하고자 했던 천인합일의 표상이자 우미와 소요를 추구한 고아한 풍류였다. 본 연구를 통해 확인된 돌바둑판은 총본 연구는 종합적인 현황 조사 분석을 통해 국내 돌바둑판의 위치 및 형태 그리고 입지 유형을 파악하는 한편 주변 경물과 각자 그리고 인근의 전래지명과의 관련성 분석과 해석을 통해 암각바둑판의 본질적 특성 및 장소적 의미 그리고 문화재로서의 가치 등을 파악하고자 하였다. 바둑판에 나타난 '네모난 바둑판과 둥근 바둑돌'의 천원지방적(天圓地方的) 형상, 흑백 바둑돌로 표상되는 음양조화 그리고 하늘 회전을 표현한 361로 등은 '우주적 질서가 투사(投射)된 상징체'이다. 또한 영원성을 바탕으로 바둑 삼매경에 빠진 '귤중지락(橘中之樂)'과 '상산사호(商山四皓)' 그리고 '난가(爛柯)' 모티프는 속세를 벗어난 망우청락(忘憂淸樂)의 '위기선미(圍棋仙味)'를 통해 '인생과 자연'의 관계를 시공간적으로 일치하고자 했던 천인합일의 표상이자 우미와 소요를 추구한 고아한 풍류였다. 본 연구를 통해 확인된 돌바둑판은 총 18개로 이중 강진 월남사지 돌바둑판, 양산 소한정 돌바둑판, 반룡대 돌바둑판 등 3개소(16.1%)는 이동이 가능한 석국으로 분류된 반면 방학동 돌바둑판을 비롯한 15개소(83.9%)는 자연 암반에 새긴, 원래 장소를 이탈하지 않은 암각바둑판으로 밝혀졌다. 돌바둑판의 입지조건을 유형화한 결과, 계류형 15개소(83.9%), 암봉형 3개소(16.1%)로 나타났으며 가장 높은 곳에 위치한 것은 소백산 신선봉 암각바둑판(1,389m)이었다. 총 15개 돌바둑판은 모두 500m 이하의 저산지에 입지하고 있는 것으로 보아 바둑판이 새겨진 입지는 속세와 멀지 않은 생활권의 일부였으며 모두 경관성이 탁월한 계곡 및 산봉에 입지하였다. 돌바둑판은 옛 선비들의 풍류와 밀접한 관련이 있는 것으로 추찰되는바 특히 암각바둑판은 천인합일(天人合一)의 조화를 추구하며 명산대천(名山大川)을 찾아 함께 노니는 풍류도의 정신을 전승한 것으로 파악된다. 즉 궁극적으로 바둑의 전통적인 상징성인 '은일의 매개체이자 자연귀의의 도에 다다를 수 있는 선비문화의 정수'인 동시에 유선적 취향의 도구로서 자리매김 하였음을 알 수 있다. 특징적으로 암각바둑판이 새겨진 단양 소백산 신선봉을 비롯하여 괴산 선국암, 무주 사선암, 장수 신선바위 등은 신선과 관련된 지명의 일체감이 매우 높은 것으로 미루어 보아 '신선' 바위와 암각바둑판이야말로 선계에 대한 숭배와 동경의 소통방식이 가장 함축적으로 표현된 경관대상이자 조망처로 판단된다. 한편 암각바둑판이 입지하는 장소의 입지유형 등 물리적 환경과 팔경 및 동천구곡의 설정 여부, 유학자 등의 관련 여부를 중심으로 한 '인간활동' 그리고 '상산사호' 모티프 및 '난가고사' 상징의미 등 3가지를 '장소정체성 판단을 위한 해석 틀'을 기준으로 하여 고찰한 결과, 암각바둑판 주변에 각자 되어있는 동천, 동문 등의 모티프는 주자학적 '구곡팔경'의 개념 보다는 선취적 '선유동천' 개념의 공간성 모색이 필요한 것으로 보인다. 전반적으로 계류형 암각바둑판이 조성된 공간은 유가의 은둔지향적 공간이나 선도적 은일지향적 공간으로 시대추이에 따라 습합되어 온 것으로 판단되며 산봉형의 암각바둑판은 별도로 신선 강림의 숭엄지향성이 장소정체성 지배의 중요 요인으로 평가된다. 아울러 암각바둑판이 조성된 곳을 포함하여 그 주변은 동천구곡이나 팔경의 일부로 널리 알려진 승경의 요처임이 확인되었다. 또한 선비 및 사대부 계층이 주체인 주변 각자들 중에도 신선 관련 표현어가 다수 발견됨에 따라 바둑판 조영의식의 이면에는 신선경 동경을 바탕으로 한 선도적 취향이 강하게 작용하고 있음이 확인되었다. 이와 같은 결과를 총합할 때 암각바둑판은 조선조 선비들의 은일과 운둔을 통한 자연경영의 문화 현상이 집약적으로 함축된 유산이자 전래 승경의 요처로, 명승과 같은 자연문화재로서의 가치가 탁월한 대상임이 확인되었다. 현재 남한내 17개의 돌바둑판 중에서 소백산 신선봉 암각바둑판을 비롯하여 방학동 암각바둑판, 충주 사로암 암각바둑판, 무주 사선암 암각바둑판, 양산 어곡동 반룡대 석국 등은 세월의 풍파와 사람들의 접촉으로 마모되면서 바위가 깨어지거나 바둑판 줄이 희미해지고 있다. 또한 언양 반구대 집청정 암각바둑판은 토사 매몰로 그 형체를 확인하기 어려운 상태이다. 암각바둑판은 자연과 바람의 흐름을 그대로 투영한 예술적, 문화재적 가치가 탁월한 조형물이자 선인들의 자연 사랑의 마음과 선계동경의 문화가 만나 이루어진 문화유적으로, 이에 대한 국내 분포 현황에 대한 체계적인 정밀조사와 보존관리가 시급하다고 사료된다. 18개로 이중 강진 월남사지 돌바둑판, 양산 소한정 돌바둑판, 반룡대 돌바둑판 등 3개소(16.1%)는 이동이 가능한 석국으로 분류된 반면 방학동 돌바둑판을 비롯한 15개소(83.9%)는 자연 암반에 새긴, 원래 장소를 이탈하지 않은 암각바둑판으로 밝혀졌다. 돌바둑판의 입지조건을 유형화한 결과, 계류형 15개소(83.9%), 암봉형 3개소(16.1%)로 나타났으며 가장 높은 곳에 위치한 것은 소백산 신선봉 암각바둑판(1,389m)이었다. 총 15개 돌바둑판은 모두 500m 이하의 저산지에 입지하고 있는 것으로 보아 바둑판이 새겨진 입지는 속세와 멀지 않은 생활권의 일부였으며 모두 경관성이 탁월한 계곡 및 산봉에 입지하였다. 돌바둑판은 옛 선비들의 풍류와 밀접한 관련이 있는 것으로 추찰되는바 특히 암각바둑판은 천인합일(天人合一)의 조화를 추구하며 명산대천(名山大川)을 찾아 함께 노니는 풍류도의 정신을 전승한 것으로 파악된다. 즉 궁극적으로 바둑의 전통적인 상징성인 '은일의 매개체이자 자연귀의의 도에 다다를 수 있는 선비문화의 정수'인 동시에 유선적 취향의 도구로서 자리매김 하였음을 알 수 있다. 특징적으로 암각바둑판이 새겨진 단양 소백산 신선봉을 비롯하여 괴산 선국암, 무주 사선암, 장수 신선바위 등은 신선과 관련된 지명의 일체감이 매우 높은 것으로 미루어 보아 '신선' 바위와 암각바둑판이야말로 선계에 대한 숭배와 동경의 소통방식이 가장 함축적으로 표현된 경관대상이자 조망처로 판단된다. 한편 암각바둑판이 입지하는 장소의 입지유형 등 물리적 환경과 팔경 및 동천구곡의 설정 여부, 유학자 등의 관련 여부를 중심으로 한 '인간활동' 그리고 '상산사호' 모티프 및 '난가고사' 상징의미 등 3가지를 '장소정체성 판단을 위한 해석 틀'을 기준으로 하여 고찰한 결과, 암각바둑판 주변에 각자 되어있는 동천, 동문 등의 모티프는 주자학적 '구곡팔경'의 개념 보다는 선취적 '선유동천' 개념의 공간성 모색이 필요한 것으로 보인다. 전반적으로 계류형 암각바둑판이 조성된 공간은 유가의 은둔지향적 공간이나 선도적 은일지향적 공간으로 시대추이에 따라 습합되어 온 것으로 판단되며 산봉형의 암각바둑판은 별도로 신선 강림의 숭엄지향성이 장소정체성 지배의 중요 요인으로 평가된다. 아울러 암각바둑판이 조성된 곳을 포함하여 그 주변은 동천구곡이나 팔경의 일부로 널리 알려진 승경의 요처임이 확인되었다. 또한 선비 및 사대부 계층이 주체인 주변 각자들 중에도 신선 관련 표현어가 다수 발견됨에 따라 바둑판 조영의식의 이면에는 신선경 동경을 바탕으로 한 선도적 취향이 강하게 작용하고 있음이 확인되었다. 이와 같은 결과를 총합할 때 암각바둑판은 조선조 선비들의 은일과 운둔을 통한 자연경영의 문화 현상이 집약적으로 함축된 유산이자 전래 승경의 요처로, 명승과 같은 자연문화재로서의 가치가 탁월한 대상임이 확인되었다. 현재 남한내 17개의 돌바둑판 중에서 소백산 신선봉 암각바둑판을 비롯하여 방학동 암각바둑판, 충주 사로암 암각바둑판, 무주 사선암 암각바둑판, 양산 어곡동 반룡대 석국 등은 세월의 풍파와 사람들의 접촉으로 마모되면서 바위가 깨어지거나 바둑판 줄이 희미해지고 있다. 또한 언양 반구대 집청정 암각바둑판은 토사 매몰로 그 형체를 확인하기 어려운 상태이다. 암각바둑판은 자연과 바람의 흐름을 그대로 투영한 예술적, 문화재적 가치가 탁월한 조형물이자 선인들의 자연 사랑의 마음과 선계동경의 문화가 만나 이루어진 문화유적으로, 이에 대한 국내 분포 현황에 대한 체계적인 정밀조사와 보존관리가 시급하다고 사료된다.