• 한국분무공학회지
• /
• 제11권3호
• /
• pp.161-167
• /
• 2006

As the exhaustion of petroleum resources and air pollution problems are getting serious recently, there are growing interests in premixed diesel engines which have the potential of achieving a more homogeneous mixture near TDC compared to conventional diesel engines. Early studies have shown that the fuel injection frequency and spray angle affected the mixture formation and combustion in a HCCI(Homogeneous Charge Compression Ignition) engine. Therefore, the purpose of this study is to investigate the relationship between combustion and mixture formations by injection timing and frequency using a narrow angle injector, NADI (Narrow Angle Direct Injection). In this study, we found that the fuel injection timing and injection frequency affect the mixture formations and then affect combustion in the HCCI engine.

• 한국분무공학회지
• /
• 제29권1호
• /
• pp.32-37
• /
• 2024

Macroscopic visualization of non-evaporating sprays was experimentally conducted to investigate spray tip penetration and spray angle under low-density conditions, corresponding to an early injection strategy. Furthermore, injectors with varying injection angles (146° and 70°) and numbers of holes (8 and 14) were employed to examine the impact of injector configuration. Compared to the baseline injector, 8H146, which has 8 holes and a 146° injection angle, the spray tip penetration of the 8H70 injector was found to be longer. This can be attributed to higher momentum due to a smooth flow field between the sac volume and the nozzle inlet, which is located closer to the injector tip centerline. The increase in velocity led to intense turbulence generation, resulting in a wider spray angle. Conversely, the spray tip penetration of the 14H70 injector was shorter than that of the 8H70 injector. The competition between increased velocity and decreased nozzle diameter influenced the spray tip penetration for the 14H70 injector; the increase in momentum, previously observed for the 8H70 injector, contributed to an increase in spray tip penetration, but a decrease in nozzle diameter could lead to a reduction in spray tip penetration. The spray angle for the 14H70 injector was similar to that of the 8H146 injector. Moreover, injection rate measurements revealed that the slope for a narrow injection angle (70°) was steeper than that for a wider injection angle during the injection event.

• 한국분무공학회지
• /
• 제14권2호
• /
• pp.71-76
• /
• 2009

The aim of this investigation is to study the effect of the high injection pressure on the dimethyl ether (DME) spray characteristics injected through a common-rail diesel injector under various ambient pressures. In order to investigate the effect of the injection pressure and ambient condition, the common-rail injection system with two high pressure pumps and high pressure chamber pressurized up to 40 bar were used, respectively. Spray images of DME fuel obtained from a visualization system composed of high speed camera and two metal halide lamps as the light source. From the obtained images, the spray behaviors such as a spray development process, spray tip penetration, spray width, and spray cone angle were measured for analyzing the DME spray characteristics under various experimental conditions. It was found that the spray development slowed as the ambient pressure increased and spray tip penetration at injection pressure of 90 MPa is longer than that at 50 MPa. In addition, the spray width at the end stage of injection decreased under the atmospheric conditions due to the evaporation property of DME fuel, and DME spray shows narrow spray cone angle according to the injection pressure increased.

• 한국자동차공학회논문집
• /
• 제19권4호
• /
• pp.16-23
• /
• 2011

Low temperature combustion is one of the advanced combustion technology in an internal combustion engine to reduce soot and nitrogen oxides simultaneously. In present experiment three kinds of injector were used to investigate the influence of injection angle and number of nozzle holes on the low temperature combustion in a heavy duty diesel engine. Low temperature diesel combustion is realized from the exhaust gas recirculation rate of 60%. Indicated mean effective pressure of low temperature combustion corresponds to the 70% level of conventional diesel engine combustion. Reduction of hydrocarbon and carbon monoxide, which are produced in low temperature combustion because of the low combustion temperature and a deficit of oxygen, was achieved by using various injector configuration. The result of experiment with $100^{\circ}$ injection angle and 8 holes showed that reductions in hydrocarbon and carbon monoxide could be achieved 58% and 27% respectively maintaining the 7% increased indicated mean effective pressure in low temperature diesel combustion compared with conventional injector.

• 한국분무공학회지
• /
• 제25권4호
• /
• pp.154-161
• /
• 2020

A single spray plume is the basic unit of the entire spray plume and is an important factor in understanding the spray characteristics. However, since the multi-hole GDI injector has a narrow spray angle, the superposition of the spray plumes occurs severely. Therefore, the spray uniformity and the spray atomization characteristics of a single spray plume were analyzed in this study using a single-hole GDI injector. Five single-hole GDI injectors with different nozzle hole diameters were used in the experiment. The uniformity of the spray was evaluated through the analysis of the spray pattern images. In addition, the atomization characteristics were compared using the diameter distribution of the spray droplets obtained using PDPA. As a result, the larger diameter of the nozzle hole, the less uniformity of the spray, and the injection pressure did not have a significant effect on the spray uniformity. It is judged that the surface roughness of the injector has a greater effect on spray uniformity than the diameter of the nozzle hole. Also, the size of the spray droplets increased sharply when the diameter of the nozzle hole was 230 ㎛.

• International Journal of Automotive Technology
• /
• 제5권4호
• /
• pp.221-238
• /
• 2004

Wall interactions of direct injection spray were investigated using laser-sheet imaging, shadowgraphy, wetted footprint and phase Doppler interferometry techniques. A narrow-cone high-pressure swirl injector is used to inject iso-octane fuel onto a plate, which has three different impact angles inside a pressurized chamber. Heated air and plate conditions were compared with unheated cases. Injection interval was also varied in the heated case to compare dry- and wet- wall impingement behaviors. High-speed macroscopic Mie-scattering images showed that presence of wall and air temperature has only minor effect on the bulk spray structure and penetration speed for the narrow-cone injector tested. The overall bulk motions of the spray plume and its spatial position at a given time are basically unaffected until a few millimeters before impacting the wall. The surface properties of the impact surface, such as the temperature, the presence of a preexisting liquid film also have a small effect on the amount of wetting or the wetted footprint; however, they have strong influence on what occurs just after impact or after a film is formed. The shadowgraph in particular shows that the plate temperature has a significant effect on vapor phase propagation. Generally, 10-20% faster horizontal vapor phase propagation is observed along the wall at elevated temperature condition. For impingement onto a preexisting film, more splash and evaporation were also observed. Contrary to some preconceptions, there is no significant splashing and droplet rebounding from surfaces that are interposed in the path of the DI gasoline spray, especially for the oblique impact angle cases. There also appears to be a dense spray front consists of large sac spray droplets in the oblique impact angle cases. The bulk of the spray is not impacted on the surface, but rather is deflected by it The microscopic details as depicted by phase Doppler measurements show that the outcome of the droplet impaction events can be significantly influenced. Only droplets at the spray front have high enough Weber numbers for wall impact to wet, splash or rebound. Using the sign of vertical velocity, the time-resolved downward droplets and upward droplets are compared. The Weber number of upward moving droplets, which seldom exceeds unity, also decreases as the impact angle decreases, as the droplets tend to impact less and move along the wall in the deflected spray plume.

• International Journal of Automotive Technology
• /
• 제5권3호
• /
• pp.155-164
• /
• 2004

The direct injection gasoline spray-wall interaction was characterized inside a heated pressurized chamber using various visualization techniques, including high-speed laser-sheet macroscopic and microscopic movies up to 25,000 frames per second, shadowgraph, and double-spark particle image velocimetry. Two hollow cone high-pressure swirl injectors having different cone angles were used to inject gasoline onto a heated plate at two different impingement angles. Based on the visualization results, the overall transient spray impingement structure, fuel film formation, and preliminary droplet size and velocity were analyzed. The results show that upward spray vortex inside the spray is more obvious at elevated temperature condition, particularly for the wide-cone-angle injector, due to the vaporization of small droplets and decreased air density. Film build-up on the surface is clearly observed at both ambient and elevated temperature, especially for narrow cone spray. Vapor phase appears at both ambient and elevated temperature conditions, particularly in the toroidal vortex and impingement plume. More rapid impingement and faster horizontal spread after impingement are observed for elevated temperature conditions. Droplet rebounding and film break-up are clearly observed. Post-impingement droplets are significantly smaller than pre-impingement droplets with a more horizontal velocity component regardless of the wall temperature and impingement angle condition.

• 한국가스학회지
• /
• 제26권3호
• /
• pp.45-53
• /
• 2022

디젤엔진의 배출물 개선을 위해 탄소수가 낮은 천연가스를 혼합하여 사용하는 천연가스-디젤 혼소 연소가 각광받고 있다. 특히 자발화 특성에 차이가 있는 디젤과 천연가스의 특성을 이용한 반응성 제어 압축착화(reactivity controlled compression ignition, RCCI) 연소 전략을 통해 기존 디젤엔진의 효율과 배출가스를 동시에 개선시키는 연구가 활발하게 진행되어 왔다. 상사점보다 앞당겨진 디젤 직접 분사시기 적용을 통해 실린더 전체 영역의 균일 혼합기를 형성하여 전체적으로 희박한 자발화 기반 연소를 달성함으로써 질소산화물 (NOx) 및 입자상물질 (PM) 저감과 제동열효율 개선을 동시에 달성할 수 있다. 하지만 매우 희박한 저부하 영역에서 불완전 연소량이 증가하는 단점이 존재하며, 안정적인 연소 구현을 위해 디젤 분사시기가 민감하게 제어되어야 하는 어려움도 존재한다. 본 연구에서는 앞서 언급된 저부하 영역에서의 천연가스-디젤 혼소 엔진의 효율 및 배기 개선을 확인하고, 동시에 발전용 엔진 구동 영역에서 디젤 분사시기에 따른 연소안정성을 평가하였다. 실험에는 6 L급 상용디젤 엔진이 사용되었으며, 1,800 rpm, 50% 부하 영역 (~50 kW)에서 실험이 진행되었다. 제동효율 및 연소안정성을 개선하기 위한 전략으로 분무 패턴이 다른 2개의 인젝터를 적용하였으며, 천연가스/디젤 비율과 디젤 분사시기를 바꿔가면서 실험이 진행되었다. 실험 결과, 협각 분사가 추가된 수정 인젝터에서 제동 열효율이 증가하는 것을 확인하였다. 또한 연소안정성 및 출력, 그리고 강화된 배기 규제를 고려하였을 때 수정 인젝터의 분무 패턴이 예혼합연소 형성에 적합하였고 이를 통해 질소산화물 배출량을 Tier-V 기준치인 0.4 g/kWh 이하로 저감함으로써 RCCI 연소 가능 영역을 확장할 수 있음을 실험적으로 확인하였다.