• 대한기계학회논문집B
• /
• 제37권8호
• /
• pp.725-732
• /
• 2013

본 논문에서는 가는 열선 주위를 흐르는 나노유체의 대류열전달 특성을 실험을 통하여 검토하였다. 입자 혼합 농도가 다른 4개의 나노엔진오일에 대하여 열선온도가 증가하는 경우, 유체온도가 증가하는 경우 그리고 막온도가 일정하게 유지되는 경우 등 세가지 온도경계조건에 대하여 대류열전달계수를 측정하였다. 내부유동에서 나노유체의 대류열전달계수 상승이 열전도율 상승을 초과한다는 결과가 최근 발표되기도 했지만 본 연구에서는 이 결과를 확인할 수 없었다. 온도조건에 따른 대류열전달계수의 변화 거동을 분석함으로써 나노유체의 열전도율과 경계층두께의 관계를 설명할 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.206-212
• /
• 2011

유체 시스템에서 히스테리시스 현상은 다양한 산업 및 공학의 응용 분야에서 발생하며, 주로 압력비의 시간변화 과정에서 발생한다. 초음속 노즐에서 충격파를 포함한 유동장은 이러한 히스테리시스 현상의 지배적인 영향을 받는다. 그러나 이와 관련된 유동의 물리적 현상에 대해서는 연구가 미비한 실정이다. 본 연구에서는 노즐구동압력비의 변화 과정 동안 초음속 노즐의 유동을 파악하기 위해 실험적 연구를 수행하였다. 순간 표면압력을 측정하기 위하여 다수의 압력변환기를 사용하였으며, 유동장의 가시화는 나노스파크 광원을 가지는 쉴리렌 가시화 장치를 이용하였다. 본 연구로부터, 히스테리시스 현상은 노즐의 기하학적 형상뿐만 아니라 압력비의 시간변화에 크게 의존하였다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.1491-1496
• /
• 2009

Fluid flow and structural analyses of an electronic expansion valve (EEV) using CO2 as a working refrigerant are carried out to estimate the mass flow rate and maximum stress. An engineering sample EEV that the orifice diameter is 1.8 mm was fabricated. The mass flow rates were measured at various EEV inlet temperatures and pressures for several EEV openings using experimental heat pump system. The sample EEV has over 35 MPa burst pressure and the maximum mass flow rate of CO2 through the EEV increased to 100 g/s at full opening condition.

• 한국생산제조학회지
• /
• 제19권2호
• /
• pp.267-274
• /
• 2010

Recently, the magnetorheological (MR) polishing process has been examined as a new ultra-precision polishing technology for mirror surface generation in many applications, such as aspheric lenses, biochips, micro parts, etc. This method uses MR fluids which contains micro abrasives as a polishing media, and can. It is possible to obtain nano level surface roughness under suitable process conditions, however, required polishing time is highly dependent on the applied pre-polishing methods due to its very small material removal rate. Thus, in this study, a combined polishing method is presented to reduce total polishing time for SUS304. First, the electropolishing (EP) method was applied to obtain fine surface roughness, and the MR polishing was followed. Surface roughness variations were investigated according to the process conditions. As the results of this study, it was possible to reduce total polishing time for SUS304 using the proposed combined polishing method.

• Archives of Pharmacal Research
• /
• 제26권10호
• /
• pp.874-879
• /
• 2003

The present study was carried out to examine the stability of microencapsulated ascorbic acid in simulated-gastric and intestinal situation in vitro and the effect of microencapsulated ascorbic acid on iron bioavailability. Coating materials used were polyglycerol monostearate (PGMS) and medium-chain triacylglycerol (MCT), and core materials were L-ascorbic acid and ferric ammonium sulfate. When ascorbic acid was microencapsulated by MCT, the release of ascorbic acid was 6.3％ at pH 5 and 1.32％ at pH 2 in simulated-gastric fluids during 60 min. When ascorbic acid was microencapsulated by PGMS, the more ascorbic acid was released in the range of 9.5 to 16.0％. Comparatively, ascorbic acid release increased significantly as 94.7％ and 83.8％ coated by MCT and PGMS, respectively, for 60 min incubation in simulated-intestinal fluid. In the subsequent study, we tested whether ascorbic acid enhanced the iron bioavailability or not. In results, serum iron content and transferring saturation increased dramatically when subjects consumed milks containing both encapsulated iron and encapsulated ascorbic acid, compared with those when consumed uncapsulated iron or encapsulated iron without ascorbic acid. Therefore, the present data indicated that microencapsulated ascorbic acid with both PGMS and MCT were effective means for fortifying ascorbic acid into milk and for enhancing the iron bioavailability.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.46-46
• /
• 2008

스텔스 기능을 가진 군사용 항공기는 레이다 망의 추적을 피하기 위해 일반 냉각수 대신에 절연유를 냉각매체로 사용한다. 그러나 절연유는 물에 비하여 열전달특성이 매우 낮기 때문에 항공기 전기전자 기기/부품 발열부를 효과적으로 냉각시키지 못하는 한계성을 가지고 있다. 따라서 본 연구에서는 나노유체(Nanofluid) 개념을 이용하여 절연유에 알루미나 및 질화알루미늄 나노분말을 미랑 분산시킨 나노절연유를 제조하고 이것의 열전달특성을 순수 절연유의 그것과 비교 평가함으로써, 냉각특성이 크게 개선된 새로운 냉매로서의 적용 가능성을 확인하고자 하였다. 다만 나노절연유를 제조함에 있어서 가장 큰 장애물은 오일에 대한 분산성 확보에 있기 때문에, 비드밀 및 초음파를 이용한 나노분말 응집체의 습식분산 및 분산제를 이용한 친유성 표면개질을 동시에 수행함으로써 장시간 안정된 분산성을 확보하도록 노력하였다. 나노유체의 열전도도 및 대류열전달계수는 비정상열선법을 이용하여 측정하였으며, 유체 속의 분말 분산 상태는 원심력을 이용한 분산안정성 평가장치 및 cryo FE-SEM을 이용하여 확인하였다. 또한 분말 형상이 대류열전달에 미치는 영향을 조사하기 위하여 알루미나 나노분말은 구상과 침상의 분말을 모두 사용하였고, 질화알루미늄 외에 다이아몬드 나노절연유도 함께 제조, 평가함으로써 냉각 및 절연특성, 그리고 물리화학적 안정성이 우수하고 실적용 가능성이 가장 높은 재료를 도출하고자 하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.360-363
• /
• 2009

In this paper, we describe new approach of ink particle fabrication method for electrophoretic display(EPD) with low voltage and rapid response time. Nano-size ink particles which fabricated using non-aqueous base modified emulsion process and micron-scale particles by non-solvent particle fabrication process are discussed. Finally, specially designed particles and panel structure fabricated considering the interactions between particle/particle, particle/media or particle/electrode dramatically reduce the driving voltages to ${\pm}$ 10V and improve the response time of less than 100msec and white reflectance of 58% for EPD using dielectric fluid as a medium. In case of EPD adapting micron-sized electrophoretic particles and a medium of air, the saturation voltage could be reduced to ${\pm}$ 40V and having white reflectance of 45% without scarification of electrophoretic mobility of the particles.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.281-285
• /
• 2008

Effective use of available energy sources is of general concern along with the issues of global warming and unstable oil price. As one of the effort to recover waste heat from industrial facilities effectively, researchers have interest in a technology called organic Rankine cycle(ORC), in which the working fluid is some organic liquid instead of water. Known to have poor efficiency already, this old technology is considered to give an innovative solution to utilizing low grade energy sources, by improving the efficiency. Nano fluidics, coatings and the use of additives are the examples of these efforts. In the present study, we present simulated performance of a horizontal tube type condenser geometry. N-hexanr and isopentane are compared to water vapor case under 1 atm and the inet cooling water temperature of $20^{\circ}C$. EES(Engineering Equations Solver) is used for the present work.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.165-169
• /
• 2008

Binary nanofluids(Binary mixture + nanoparticles) have been extensively paid attention for application in absorption system as a new working fluid. Thermal property evaluation of the new refrigerants is inevitable to apply them for actual system. The objectives of this paper are to measure the thermal conductivity of the binary nanofluids by the transient hot-wire method, and to assess the application possibility of the binary nanofluids for absorption system. It was found that the thermal conductivity of the binary nanofluids ($H_2O/LiBrAl_2O_3$) increased with increasing the concentration of the nanoparticles ($Al_2O_3$) and enhanced up to 27% at 0.1 vol % of the nanoparticles.

• 반도체디스플레이기술학회지
• /
• 제9권4호
• /
• pp.19-23
• /
• 2010

Nanoimprint lithography (NIL) is one of the most versatile and promising technology for micro/nano-patterning due to its simplicity, high throughput and low cost. Recently, one of the major trends of NIL is large-area patterning. Especially, the research of the application of NIL to TFT-LCD field has been increasing. Technical difficulties to keep the uniformity of the residual layer, however, become severer as the imprinting area increases. In this paper we performed a numerical study for a large area NIL (the $2^nd$ generation TFT-LCD glass substrate ($370{\times}470$ mm)) by using finite element method. First, a simple model considering the surrounding wall was established in order to simulate effectively and reduce the computing time. Then, the volume of fluid (VOF) and grid deformation method were utilized to calculate the free surfaces of the resist flow based on an Eulerian grid system. From the simulation, the velocity fields and the imprinting pressure during the filling process in the NIL were analyzed, and the effect of the surrounding wall and the uniformity of residual layer were investigated.