• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.144-149
• /
• 2004

Porous anodic alumina has been used widely for corrosion protection of aluminum surfaces or as dielectric material in micro-electronics applications. It exhibits a homogeneous morphology of parallel pores which can easily be controlled between 10 and 400nm. It has been applied as a template for fabrication of the nanometerscale composite. In this study, mechanical properties of the AAO structures are measured by the nano indentation method. Nano indentation technique is one of the most effective method to measure the mechanical properties of nano-structures. Basically, hardness and elastic modulus can be obtained by the nano-indentation. Using the nano-indentation method, we investigated the mechanical properties of the AAO structure with different size of nano-holes. In results, we find the hole effect that changes the mechanical properties as size of nano hole.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.186-193
• /
• 2004

Porous anodic alumina has been used widely for corrosion protection of aluminum surfaces or as dielectric material in micro-electronics applications. It exhibits a homogeneous morphology of parallel pores which can easily be controlled between 10 and 400nm. It has been applied as a template for fabrication of the nanometer-scale composite. In this study, mechanical properties of the AAO structures are measured by the nano indentation method. Nano indentation technique is one of the most effective methods to measure the mechanical properties of nano-structures. Basically, hardness and elastic modulus can be obtained by the nano-indentation. Using the nano-indentation method, we investigated the mechanical properties of the AAO structure with different size of nano-holes. In results, we find the hole effect that changes the mechanical properties as size of nano hole.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.11
• /
• pp.2029-2033
• /
• 2007

Hydrotalcite, layered double hydroxides (LDH), with hexagonal morphology has been rapidly synthesized by microwave reaction within 1 hour by urea hydrolysis from homogeneous solution. Different synthesis parameters, Mg/Al molar ratio, microwave reaction temperature and microwave power were systematically investigated. Pure hydrotalcite phase was obtained for Mg/Al ratios of 2:1 and 3:1, and higher reaction temperature gave higher crystallinity. The hydrotalcite synthesized at 600W power shows the highest crystallinity and more homogeneous crystal size distribution. The hydrotalcite samples were characterized by powder X-ray diffraction (XRD), simultaneous thermogravimetric/differential thermal analysis (TG/DTA), Fourier Transform Infrared (FT-IR) and Scanning electron micrograph (SEM).

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.304-307
• /
• 2012

Nano-fibers of LiFePO4 were synthesized from a metal oxide precursor by adopting electrospinning method. After calcination of the above precursor nano-fibers at 800 ℃, LiFePO4 nano-fibers with a diameter of 300 ~ 800 nm, were successfully obtained. Measurement were performed using X-ray diffraction (XRD), fourier transform infrared spectrometer (FT-IR), videoscope, scanning electron microscope (SEM) and atomic force microscope (AFM), respectively, were performed to characterize the properties of the as-prepared materials. The results showed that the crystalline phase and morphology of the fibers were largely influenced the starting materials and electrospinning conditions.

• Journal of Surface Science and Engineering
• /
• v.40 no.1
• /
• pp.32-38
• /
• 2007

Ni coating layers were formed using a newly developed electroless Ni plating solution. The properties of Ni coating layer such as internal stress, hardness, surface roughness, crystallinity, solderability and surface morphology were investigated using various tools. Results revealed that internal stress decreased with plating time and reached $40N/mm^2$ at 20 minutes of the plating time. Hardness increased with increasing P content and thickness. Surface roughness of the pad decreased with Ni and Ni/Au plating. Crystallinity decreased with increasing P content. Solderability based on wettability decreased with Ni and Ni/Au plating. Based on surface morphology, it is expected that Ni coating layer formed using a newly developed electroless Ni plating solution is lower than that formed using a commercial electroless Ni plating solution in possibility of black pad occurrence.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.5
• /
• pp.1007-1012
• /
• 2008

Spray pyrolysis has been found as an excellent method for the preparation of mesoporous barium sulfate at higher temperature. Ethylene glycol, a reducing agent, and solvents had good inhibition effect for the preparation of $BaSO_4$ nano particles. The $BaSO_4$ solution was sprayed at 500 & 800 ${^{\circ}C}$ using different solvents such as methanol, ethanol, propanol and n-butyl alcohol. $N_2$ adsorption-desorption isotherm revealed that $BaSO_4$ is micropore free, possessing narrow mesopores size distribution and high BET surface areas of 72.52 $m^2\;g^{-1}$ at 800 ${^{\circ}C}$ using propanol as an additive. Scanning electron microscopy (SEM) indicates that the morphology of $BaSO_4$ nano material shows uniform shell like particles. Transmission electron microscopy (TEM) proved that the resulting BaSO4 nano particles were uniform in size and the average particle size was 4-8 nm. The surface functionality and ethylene glycol peaks were assessed by Fourier transform infrared resonance (FTIR) spectroscopy. Low intensity ethylene glycol specific absorption peak was observed in propanol which proved that propanol had good inhibition effect on the structural morphology of nano particles.

• Journal of the Korean Ceramic Society
• /
• v.43 no.9 s.292
• /
• pp.564-568
• /
• 2006

AlO(OH) nano gel is used in precursor of ceramic material, coating material and catalyst. For use of these, not only physiochemical control for particle morphology, pore characteristic and peptization but also studies of synthetic method for preparation of advanced application products were required. In this study, AlO(OH) nano gel was prepared through the aging and drying process of aluminum hydroxides gel precipitated by the hydrolysis reaction of dilute NaOH solution and aluminum sulfate solution. In this process, optimum synthetic condition of AlO(OH) nano gel having excellent pore volume as studying the effect of water and aluminum sulfate mole ratio on gel precipitates has been studied. Water and aluminum sulfate mole ratio brought about numerous changes on crystal morphology, surface area, pore volume and pore size. Physiochemical properties were investigated as using XRD, TEM, TG/DTA, FT-IR, and $N_2$ BET method.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.434-434
• /
• 2011

Electrochemical method have been employed in this work to modify the chemical vapour deposited nitrogen doped hydrogen amorphous diamond-like carbon (N-DLC) film to fabricate nickel and copper nano particle modified N-DLC electrodes. The electrochemical behaviour of the metal nano particle modified N-DLC electrodes have been characterized at the presence of glucose in electrolyte. Meanwhile, the N-DLC film structure and the morphology of metal nano particles on the N-DLC surface have been investigated using micro-Raman spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy. The nickel nano particle modified N-DLC electrode exhibits a high catalytic activity and low background current, while the advantage of copper modified N-DLC electrode is drawn back by copper oxidizations at anodic potentials. The results show that metal nano particle modification of N-DLC surface could be a promising method for controlling the electrochemical properties of N-DLC electrodes.

• Textile Coloration and Finishing
• /
• v.23 no.2
• /
• pp.146-153
• /
• 2011

Silver nano-particles have been synthesized by liquid phase reduction method and alcohol reduction process. Silver nano-particles of the size 30 ~ 40 nm were formed successfully by alcohol reduction process. The formation, structure, morphology and size of silver nano-particles have been studied using FE-SEM, TEM, XRD, UV-visible spectroscopy. In particular high dispersion stability of the synthesized silver nano-particles could be obtained by PVP binding. Antibacterial activity of Ag/PET master batch sample made from its nano-silver particles showed excellent antibacterial activity against S. aureus and E. coli.

• Korean Journal of Materials Research
• /
• v.25 no.4
• /
• pp.209-213
• /
• 2015

Synthesis of nano-silica using water glass in a Sol-Gel process is one of several methods to manufacture nano-silica. In nano-silica synthesized from water glass, there are various metal impurities. However, synthesis of nano-silica using water glass in a Sol-Gel process is an interesting method because it is relatively simple and cheap. In this study, nano-silica was synthesized from water glass; we investigated the effect of pH on the synthesis of nano-silica. The morphology of the nanosilica with pH 2 was flat, but the surface of the nano-silica with pH 10 had holes similar to small craters. As a result of ICP-OES analysis, the amount of Na in the nano-silica with pH 2 was found to be 170 mg/kg. On the other hand, the amount of Na in the nano-silica with pH 10 was found to be 56,930 mg/kg. After calcination, the crystal structure of the nano-silica with pH 2 was amorphous. The crystal structure of the nano-silica with pH 10 transformed from amorphous to tridymite. This is because elemental Na in the nano-silica had the effect of decreasing the phase transformation temperature.