• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1552-1555
• /
• 2005

We have studied the inkjet patterning of synthesized aqueous silver nano-sol on interface-controlled ITO glass substrate. Furthermore, we designed the conductive ink for direct inkjet patterning on bare ITO glass substrate. The first, the highly concentrated polymeric dispersant-assisted silver nano sol was prepared by variation of molecular weight and control of initial nucleation and growth of silver nanoparticles. The high concentration of batch-synthesized silver nano sol was possible to 40 wt%. At the same time the particle size of silver nanoparticles was below $10{\sim}20nm$. The second, the synthesized silver nano sol was inkjet - patterned on ITO glass substrate. The connectivity and width of fine line depended largely on the wettability of silver nano sol on ITO glass substrate, which was controlled by surfactant. The relationship was understood by wetting angle. The fine line of silver electrode as fine as $50{\sim}100\;{\mu}m$ was successfully formed on ITO glass substrate. The last, the direct inkjet-patternable silver nano sol on bare ITO glass substrate was designed also.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.4
• /
• pp.716-722
• /
• 2017

In this paper, a fully printed NFC tag operating at 13.56 MHz was designed and fabricated using silver nano-paste and carbon ink. The proposed NFC tag has a printed coil with an inductance of $2.74{\mu}H$ on a PI film for application to an NFC tag IC with an internal capacitance of 50 pF. Screen printing technology used in this paper has advantages such as large area printing for mass production, low cost and eco-friendly process compared to conventional PCB manufacturing process. The proposed structure consists of a circular coil implemented as a single layer using silver nano-paste and carbon ink, a jumper pattern for chip mounting between the outer edge and the center of the coil, and an insulation pattern between the coil and the jumper pattern. In order to verify the performance of the proposed NFC tag, we performed the measurements of the printing line width, thickness, line resistance, adhesion and environmental reliability, and confirmed the suitability of the NFC tag based on the full-printed manufacturing method.

• Journal of the Korean Ceramic Society
• /
• v.54 no.3
• /
• pp.243-248
• /
• 2017

Pd-doped $SnO_2$ thick film with a pure tetragonal phase was prepared on patterned Pt electrodes by an ink dropping method. Nanostructured $SnO_2$ powder with a diameter of 10 nm was obtained by a modified hydrazine method. Then the ink solution was fabricated by mixing water, glycerol, bicine and the Pd-doped $SnO_2$ powder. When the Pd doping concentration was increased, the grain size of the Pd-doped $SnO_2$ thick film became smaller. However, an agglomerated and extruded surface morphology was observed for the films with Pd addition over 4 wt%. The orthorhombic phase disappeared even at a low Pd doping concentration and a PdO peak was obtained for a high Pd doping concentration. The crack-free Pd-doped $SnO_2$ thick films were able to successfully fill the $30{\mu}m$ gap of the patterned Pt electrodes by the optimized ink dropping method. The prepared 3 wt% Pd-doped $SnO_2$ thick films showed monoxide gas responses ($R_{air}/R_{CO}$) of 4.0 and 35.6 for 100 and 5000 ppm, respectively.

• Korean Journal of Materials Research
• /
• v.21 no.3
• /
• pp.149-155
• /
• 2011

We investigated tribological characteristics of diamond-like carbon (DLC) in a condition with carbon nanotube (CNT) content of 1wt% in aqueous solution. Si-DLC films were deposited by radio frequency plasma enhanced chemical vapor deposition (RF-PECVD) process on Al6061 aluminum alloy. In this study, the deposition of DLC films was carried out in vacuum with a chamber pressure of 10-5 to 10-3 Torr achieved by mechanical pump followed by turbo molecular pump. The surface adsorbed oxygen on the Aluminum substrates was removed by passing Ar gas for 10 minutes. The RF power was maintained at 500W throughout the experiment. A buffer layer of HMDSO was deposited on the substrate to improve the adhesion of DLC coating. At this point CH4 gas was introduced in the chamber using gas flow controller and DLC coating was deposited on the buffer layer along with HMDSO for 50 min. The thickness of 1 ${\mu}m$ was obtained for DLC films on aluminum substrates The tribological properties of as synthesized DLC films were analyzed by wear test in the presence of dry air, water and lubricant such as CNT ink.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.372-373
• /
• 2006

Modern business trends call for miniaturization of electronic systems. One of the major impedances in this miniaturization is the conductive and inductive components in chips and circuit boards. Direct Write Technology can write these soft magnetic materials, thus allowing for further miniaturization of inductor devices. Another obstacle in electronics fabrication is the size limitations of thick screen-printing and the material limitations in ink jet printing. Direct Write Technologies address both of these limitations by providing feature sizes less than 20 microns with a wide range of materials possibilities. A discussion of the application of these nano-particulate materials by Direct Write Technologies will be presented.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.236-237
• /
• 2007

A single-wall carbon nanotube (SWNT) transparent conductive film (TCF) was fabricated using a simple inkjet printing method. The TCF could be selectively patterned by controlling the dot size to diameters as small as 34${\mu}m$. In thisrepeatable and scalable process, we achieved 71% film transmittance and a resistance of 900 ohm/sq sheet with an excellent uniformity, about $\pm$5% deviation overall. Inkjet printing of SWNT is substrate friendly and the TCF is printed on a flexible substrate. This method of fabrication using direct printing permits mass production of TCF in a large area process, reducing processing steps and yielding low-cost TCF fabrications on a designated area using simple printing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.426-426
• /
• 2007

We report the field emission characteristics of transparent single-walled carbon nanotube (SWNT) film printed using an inkjet. Pure SWNTs dispersed in dimethylformamide were printed in a transparent layer on indium-tin oxide-coated glass and annealed at $350^{\circ}C$. After taping treatment, SWNTs were oriented vertically on the substrate. The front and the back of the fabricated device produced simultaneous emissions of identical quality. In addition, inkjet printing directly achieved a patterned emission, without a secondary pattern process. This method allows simple fabrication using only SWNTs, without the use of other additives.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.63-63
• /
• 2010

나노 구조를 제작은 나노 기술을 기반으로 하는 electronics, optoelectronics, sensing, ultra display등의 여러 분야에서 이용되고 있다. 특히 나노 구조를 갖는 금속 패터닝의 경우 전자빔 리소 그래피 (electron beam lithography)나 레이저 패터닝(laser patterning)과 같은 방법들이 많이 사용되고 있다. 하지만 공정이 복잡하고 그로 인해 공정 비용이 많이 든다는 단점이 있었다. 나노 임프린트 리소그래피 기술은 master mold 표면의 나노 패턴을 가열, 가압 공정을 통해 기판 위의 고분자 레지스트 층으로 전사하는 기술이다. 이 기술은 간단한 공정을 통해 나노 패턴을 형성할 수 있는 기술이기 때용에 차세대 나노 패터닝 기술로써 각광받고 있다. 특히 이 기술은 레지스트 층과의 직접적인 접촉을 통해 나노 패턴을 형성하기 때문에 다양한 방법을 통해 기능성 나노 패턴을 직접적으로 형성할 수 있는 가능성을 지니고 있다. 본 연구는 novel meta1의 하나인 Ag 입자가 첨가된 ink solution를 master mold로부터 복제한 PDMS mold를 이용하여 다양한 구조의 나노 패턴을 만드는 방법에 대한 연구이다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.352-358
• /
• 2019

In recent years, printing paper with a function of information delivery and aesthetic value has attracted a great attention with increasing market demand for coated paper that is capable of high quality printing. The coated paper for inkjet printing with high-quality of photorealistic grades requires the coating layer with a good wettability and porous surface structure in order to improve the printability of ink. In this study, the coated paper was prepared using polyvinyl alcohol (PVA) and surface treated nano silica sol with silane coupling agent. It was confirmed that the coating layer with surface treated nano silica sol showed a uniform pore distribution and flat surface roughness. Glossiness of the prepared printing paper was similar to that of commercial high quality photo paper. Especially, the coated paper with surface treated nano silica sol showed improved printability with excellent roundness of the printed dot of ink. These results indicates that the coating layer with excellent wettability and uniform pore distribution can be formed by using the nano-silica particles with improved dispersibility through the surface treatment of the silane coupling agent.

• Journal of Adhesion and Interface
• /
• v.19 no.4
• /
• pp.163-166
• /
• 2018

Dip-pen nanolithography(DPN) is an atomic force microscope (AFM) based method of generating nano- or micro-patterns. This technique has been used to transfer various ink materials on the substrate through water meniscus formed between AFM tip and the substrate surface. In this study, the heptadecafluoro-1,1,2,2-tetrahydrodecyltrimethoxysilane (HDFDTMS) ink materials were coated on the pre-coated AFM tip surface with the HDFDTMS molecules. When the tip brought into contact with the hydroxyl-functionalized silicon surface, HDFDTMS ink molecules have been successfully transported from the tip onto the surface via water meniscus. The created array and passivation area showed stable structures on the surface, and the transport of ink materials from the AFM tip to the surface followed linear increase in pattern size with contact time.