• Korean Journal of Metals and Materials
• /
• v.46 no.6
• /
• pp.351-356
• /
• 2008

Thermally sprayed tungsten carbide-based powder coatings are being widely used for a variety of wear resistance applications. The coating deposited by high velocity processes such as high velocity oxy-fuel (HVOF) thermal spraying is known to provide improved wear resistant property. In this study, optimal coating process (OCP) is obtained by the study of coating properties such as surface hardness, porosity, surface roughness and microstructure of 9 coatings prepared by Taguchi program for 3 levels of four spray parameters. The Friction and wear behaviors of HVOF WC-CoCr coating prepared by OCP, electrolytic hard chrome (EHC) plating and Inconel718 (In718) are investigated by reciprocating sliding wear test at $25^{\circ}C$, $450^{\circ}C$. Friction coefficients (FC) of all of the 3 samples are decreased as increasing sliding surface temperature from $25^{\circ}C$ to $450^{\circ}C$. FC of WC-CoCr decreases as increasing the surface temperature from $0.33{\pm}0.02$ at $25^{\circ}C$ to $0.26{\pm}0.02$ at $450^{\circ}C$, showing the lowest FC among the 3 samples. Wear trace (WT) and wear depth (WD) of WC-CoCr are smaller than those of EHC and In718 both at $25^{\circ}C$ and $450^{\circ}C$. These show that WC-CoCr is highly recommendable for protective coating on In718 and other metal components.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.1794-1798
• /
• 2014

Graphitic g-$C_3N_4-WO_3$ composite was synthesized simply by decomposing melamine in the presence of $WO_3$ at $500^{\circ}C$. The obtained material was characterized by XRD, SEM, IR and XPS. The results showed that the as-prepared composite exhibits orthorhombic $WO_3$ phase coated by g-$C_3N_4$ and the g-$C_3N_4$ decomposed completely with N-doped $WO_3$ remaining at elevated calcination temperatures. The photocatalytic activity of the composite was evaluated by the photodegradation of methylene blue under visible light. An enhancement in photocatalytic activity for the graphitic g-$C_3N_4-WO_3$ composite compared to the conventional nitrogen-doped $WO_3$ was observed, which can be attributed to the presence of g-$C_3N_4$ in the material.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.9
• /
• pp.1110-1116
• /
• 2004

Experimental measurements of laser-induced ion mobility(LIIM) were performed for ethene/air premixed flames operated near the soot inception point. Soot was ionized using a pulsed laser operated at 532 nm. The ionization signal was collected with a tungsten electrode located in the post-flame region. ionization signals were collected using both a single electrode and dual electrode configuration. Prior LIIM studies have focused on the use of a single biased electrode to generate the electric field, with the burner head serving as the path to ground. In many practical combustion systems, a path to ground is not readily available. To apply the LIIM diagnostic to these geometries, a dual electrode geometry must be employed. The influence of electrode configuration, flame equivalence ratio, and flame height on ionization signal detection was determined. The efficacy of the LIIM diagnostic to detect soot inception in the post-flame region of a premixed flame using a dual electrode configuration was investigated. For the different dual electrode configurations tested, the dual parallel electrode geometry was observed to be most sensitive to detect the soot inception point in a premixed flame.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1218-1219
• /
• 2008

Thin films (< 30 nm) of titanium carbide (TiC) are coated on carbon nanotubes (CNTs), which are directly grown on nano-sized ($\sim$ 500 nm in diameter) conical-type tungsten (W) tips, by employing an inductively coupled plasma-chemical vapor deposition (ICP-CVD) technique. Any modification in structural properties (such as length to diameter ratio, crystal quality, and growth behavior) of CNTs due to TiC-coating has been monitored by using high-resolution TEM, field-emission SEM, and Raman spectroscopy. Driving voltage for obtaining the same level of emission current in CNTs-emitter is significantly reduced by TiC-coating. It is also worthy of being noted that the degradation of emission current due to prolonged operation (up to 30 h) is remarkably suppressed by TiC-coating.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.236.1-236.1
• /
• 2014

Compounds of Ga, such as gallium oxide (Ga2O3) and gallium nitride (GaN), are of interest due to its unique properties in semiconductor application. In particular, GaN has the potentially application for optoelectronic device such as light-emitting diodes (LEDs) and laser diodes (LDs) [1]. Nanoparticle is an interesting material due to its unique properties compared to the bulk equivalents. In this report, we develop a synthesizing method for gallium nitride nanoparticle using non-thermal plasma. For gallium source, the gallium is heated by thermal conduction of tungsten boat which is heated by eddy current induced from RF current in antenna. Nitrogen source for nanoparticle synthesis are from inductively coupled plasma with N2 gas. The synthesized nano particles are analyzed using field-emission scanning microscope (FESEM), transmission electron microscope (TEM) and x-ray photoelectron spectroscopy (XPS). The synthesized particles are investigated and discussed in wide range of experiment conditions such as flow rate, pressure and RF power.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.172-172
• /
• 2011

현대 반도체 금속배선 연구에서는 기존에 쓰이던 Al (Aluminium) 금속배선 대신에 Cu(Copper) 금속배선 연구가 진행 되고 있다. Cu는 Al 보다 비저항이 낮고, 녹는점도 Al보다 높다는 장점이 있지만 저온에서 기판인 Si (Silicon) 과 반응하고 접착력이 우수하지 못 하다는 단점이 있다. 이런 문제를 해결하기 위하여 확산방지막을 기판과 금속배선 사이에 삽입하는 방법이 제시 되었다. 확산방지막으로는 기존에 쓰이던 Ti (Titanium) 계열의 확산방지막과 W (Tungsten) 계열의 확산방지막이 있다. 이번 연구에서는 W 계열의 확산방지막에 불순물 C (Carbon), N(Nitrogen)을 첨가한 W-C-N 확산방지막 시편을 제조하였고, N2의 비율을 변화시키며 $600^{\circ}C$ 열처리를 하였다. 실험 결과 질소의 포함 농도에 따라 확산방지막의 안정도가 변화한다는 결과를 얻었으며, 질소 첨가량에 따라 시편의 표면 보다는 시편의 중간층의 물성 변화율이 큰데 이는 시편 표면의 질소는 열처리 중 확산에 의한 시편과의 분리 현상이 일어나지만 시편의 중간층은 trap현상에 의하여 시편에 남아있어 질소의 영향을 받아 시편의 중간층이 더욱 질소 유량에 따른 영향이 큰 것을 확인하였다. 이 결과로부터 W-C-N 박막은 첨가된 질소의 유량에 따라 박막의 안정도가 결정된 다는 것을 알았다. 본 연구에서 시편은 rf magnetron sputtering 방법으로 제작하였고 연속압입 실험은 Hysitron사의 Triboindenter를 이용하였다. Indenting에 사용된 압입팁은 Berkovich tip을 사용하였다.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.5
• /
• pp.213-219
• /
• 2011

Recently aspheric lenses are widely used for superpricision optical instruments, such as cellular phone camera modules, digital cameras and optical communication modules. The aspherical lenses are processed using mold core under high temperature compressive forming pressure. It is imperative to develop superhard protective films for the life extension of lens forming mold core. Especially ta-C films with higher $sp^3$ fractions receive attentions for the life extension of lens forming mold and, in turn, the cost reduction of lenses due to their suprior high temperature stability, high hardness and smooth surfaces. In this study ta-C films were processed on WC mold as a function of substrate bias voltage using FVA (Filtered Vacuum Arc) method. The processed films were characterized by Raman spectroscopy and nano-indentation to investigate bonding nature and hardness, respectively. The film with maximun 87% of $sp^3$ fraction was obtained at the substrate bias voltage of -60 V, which was closest to ta-C film. ta-C films showed better high temperature stability by sustaining relatively high fraction of $sp^3$ bonding even after 2,000 glass lens forming applications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.3
• /
• pp.229-233
• /
• 2011

Diamond thin films were deposited on pretreated Co cemented tungsten carbide (WC-6%Co) inserts as substrate by microwave plasma chemical vapor deposition (MPCVD) system, equipped with a 915MHz, 30kW generator for generating a large-size plasma. The substrates were pretreated with two solutions Murakami solution $[KOH:K_3Fe(CN)_6:H_2O]$ and nitric solution $[HNO_3:H_2O]$ to etch, WC and Co at cemented carbide substrates, respectively. The deposition experiments were performed at an input power of 10 kW and in a total pressure of 100 torr. The influence of various $CH_4$ contents on the crystallinity and morphology of the diamond films deposited in MPCVD was investigated using scanning electron microscopy (SEM) and Raman spectroscopy. The diamond film synthesized by the $CH_4$ plasma shows a triangle-faceted (111) diamond. As $CH_4$ contents was increased, the thickness of diamond films increased and the faceted planes disappeared. Finally, Faceted diamond changed into nano-crystalline diamond with random crystallinity.

• Korean Journal of Metals and Materials
• /
• v.48 no.11
• /
• pp.1009-1013
• /
• 2010

Extremely dense WC with a relative density of up to 99% was obtained within five minutes under a pressure of 80 MPa using the High-Frequency Induction Heated Sintering method. The average grain size of the WC was about 71 nm. The advantage of this process is not only rapid densification to obtain a neartheoretical density but also the prohibition of grain growth in nano-structured materials. The hardness and fracture toughness of the dense WC produced by HFIHS were $2660kg{\cdot}mm^{-2}$ and $7.2MPa{\cdot}m^{1/2}$, respectively.

• Elastomers and Composites
• /
• v.56 no.3
• /
• pp.172-178
• /
• 2021

The wear behavior of styrene-butadiene rubber (SBR) and butadiene rubber (BR) was investigated using a blade-type abrader with a steel blade (SB), Ti-coated tungsten carbide blade (TiB), or zirconia blade (ZB). The wear rate of SBR against SB and TiB decreased with increasing number of revolutions because of the blunting of the blades during wear. However, the wear rate of SBR against ZB remained nearly constant with little blade blunting. Generally, the wear rate of BR was largely unaffected by the blade material used for abrasion. The wear rate and frictional coefficient of SBR were found to be higher than those of BR at similar levels of frictional energy input. A power-law relationship was found between the wear rate and frictional energy input during abrasion. A well-known Schallamach pattern was observed for SBR, while a much finer pattern was observed for BR. The blade material affects the wear rate of the rubbers because the macromolecular free radicals and blade tend to undergo mechano-chemical reactions. The inorganic ZB was found to be the most inert for such a mechanism.