• 폴리머
• /
• 제38권3호
• /
• pp.358-363
• /
• 2014

원자력현미경(AFM) tip을 표면 처리하여 임프린트용 acrylate 레진과의 접착력을 측정하였다. 표면 처리를 하지 않은 실리콘 tip에 비하여 $CH_4$ 플라즈마로 소수성 처리한 경우 접착력은 38% 감소한 반면 친수성의 $O_2$ 플라즈마로 처리한 경우에는 접착력이 1.6 배 증가하였다. 이러한 AFM 결과들은 정성적 실험 결과 밖에 얻을 수 없는 cross-cut 접착실험에 비하여 매우 구체적인 정량적 결과들을 제공하였다. 나노 크기의 임프린트 패턴을 전사하는 경우, 몰드와 레진 사이 접촉 면적이 커져서 시료 전체의 접착력이 커지기 때문에 패턴 크기가 작아지는 나노임프린트 공정에서는 몰드 표면 처리 문제가 더욱 중요하게 되는 것을 알 수 있었다.

• 한국유체기계학회 논문집
• /
• 제9권2호
• /
• pp.19-24
• /
• 2006

Nano fountain-pen is a novel device to make the constant patterning in micro process using new designed probe. Fountain-pen nanolithography (FPN) is applied for constant supply of liquid in conjunction of patterns and surface variation in the micro process. In this study, nuo fountain-pen is composed with reservoir, micro channels, tip and scondary chamber. Instead of traditional method only using capillary force, liquid can be definitely and exactly injected with membrane pumping by the repulse force of tip. It is dfficult to perform experiments in the micro range so that we carried out a numerical analysis for internal flow, using a commercial code, FlUENT, The velocity, pressure and flow rate are obtained under laminar, unsteady, three-dimensional incompressible flow with no-slip condition, and results are graphically described.

• Journal of Mechanical Science and Technology
• /
• 제18권10호
• /
• pp.1772-1781
• /
• 2004

The mechanical as well as tribological characteristics of coating films as thin as a few nm become more crucial as applications in micro-systems grow. Especially, the amorphous carbon film has a potential to be used as a protective layer for micro-systems. In this work, quantitative evaluation of nano-indentation, scratching, and wear tests were performed on the 7nm thick amorphous carbon film using an Atomic Force Microscope (AFM). It was shown that AFM-based nano-indentation using a diamond coated tip can be feasibly utilized for mechanical characterization of ultra-thin films. Also, it was found that the critical load where the failure of the carbon film occurred was about 18${\mu}$N by the ramp load scratch test. Finally, the wear experimental results showed that the quantitative wear rate of the carbon film ranged 10$\^$-9/～10$\^$-8/ ㎣ /N cycle. These experimental methods can be effectively utilized for a better understanding the mechanical and tribological characteristics at the nano-scale.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.492-497
• /
• 2005

In this study, we propose an advanced nanoindentaion test, Nano Pillar Compression Test (NPCT) to measure a stress-strain relation for micro scale polymer structures. Firstly, FEM analysis is performed to research behavior of micro polymer pillars in several specimen aspect ratios and different friction conditions between specimen and tip. Based on the FEM results, micro scale UV-curable polymer pillars are fabricated on a substrate by Nano Stereo Lithography (NSL). To measure their mechanical properties, uniaxial compression test is performed using nanoindentation apparatus with flat-ended diamond tip. In addition, the dependency of compression properties on loading condition and specimen size are discussed.

• 한국기계가공학회지
• /
• 제17권6호
• /
• pp.1-6
• /
• 2018

Recently nano meter size pattern (sub-micro scale) can be machined mechanically using a diamond tool. Many studies have found a 'size effect' which referred to a specific cutting energy increase with the decrease in the uncut chip thickness at micro scale machining. A new analysis method was suggested in order to observe 'size effect' in nano scale machining and to verify the cause of the 'size effect' in this study. The diamond tool was indented to a vertical depth of 1,000nm depth in order to simplify the stress state and the normal force was measured continuously. The tip rounding was measured quantitatively by AFM. Based on the measurements and theoretical analysis, it was verified that the main cause of the 'size effect' in nano scale machining is geometrically necessary dislocations, one of the intrinsic material characteristics. st before tool failure.

• 한국표면공학회지
• /
• 제47권6호
• /
• pp.362-367
• /
• 2014

We report the design, fabrication of a $Si_3N_4$ probe and calculation of its mechanical properties for DPN(dip pen nanolithography), which consists of dual tips. Concept of dual tip probe is to employ individual tips on probe as either an AFM tip for imaging or a writing tip for nano patterning. For this, the dual tip probe is fabricated using low residual stress $Si_3N_4$ material with LPCVD deposition and MEMS fabrication process. On the basis of FEM analysis we show that the functionality of dual tip probe for imaging is dependent on the dimensions of dual tip probe, and high ratio of widths of beam areas is preferred to minimize curvature variation on probe.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1030-1035
• /
• 2003

The nanoimprint lithography technology makes higher density of semiconductor device and larger capacity of storage media. In this technology the induced damage while detaching polymer pattern from mold should be minimized. In order to analyze the problem, the basic knowledge of adhesion between the polymer and the mold is required. In this study a contact experiment of polyisobutylene specimen with spherical steel tip and polyisobutylene bead tip was conducted using nano indenter. During the contact experiment with various loading rate under load control the contact behavior of viscoelastic material was measured, i.e., the load and displacement between the tip and the specimen were measured. The data was analyzed by HBK model to obtain the stress intensity factor of contact edge and the contact radius as a function of time. Also the adhesion energies between steel/polyisobutylene and polyisobutylene/polyisobutylene were obtained employing the analysis of the crack of viscoelastic material by Schapery.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1963-1966
• /
• 2008

We fabricate and evaluate the metal-oxide-semiconductor (MOS) transistor probe with the focused-ionbeam (FIB) for surface electric properties. The probes are designed with the rectangular and V-shaped structures, and their dimensions are determined considering the contact mode operation. The conductive nano tip is grown with FIB system, and deposition condition is controlled for the sharp tip. The fabricated device is applied to the various test patterns like the metal lines and PZT poling regions, and the results show the well defined measurement patterns.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 춘계학술대회 논문요약집
• /
• pp.161-161
• /
• 2004

AC 이중전기영동(AC electrophoresis)의 원리를 이용하여 탄소나노튜브 팁 제작용 탄소나노튜브 시편의 기초 실험을 수행하였다. 본 연구에서 사용한 방법은, 끝이 뽀족한 다수의 팁(tip)에 탄소나노튜브를 비교적 균일하게 부착시킬 수 있는 공정의 기반이 된다. 이것은 탄소나노튜브를 이용한 나노팁(nano-tip)이나 탄소나노튜브 나노그리퍼(nanogripper) 제작 공정에 균일성을 확보할 수 있는 중요한 방법으로 활용될 수 있다. 탄소나노튜브 시편의 제작을 위해, 끝단이 곡률반경이 50nm 정도인 텅스텐 팁과 직경 1.5mm, 깊이 1.5mm의 실린더형 금속전극을 사용했다.(중략)

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.4-4
• /
• 2010

박막의 물성을 분석하는 방법에는 광학을 이용한 분광학 분석법과 나노크기의 tip을 이용한 나노트라이볼로지 분석법이 대표적이라 할 수 있다. 분광학 분석법에는 주로 X-ray 회절분석, Raman 분광기, IR 분광기 등등이 가장 대표적으로 사용되어지는 분석 장치들이다. 이러한 분광학 분석은 광학을 시료에 조사하여 이로부터 획득되는 강도(intensity)를 분석하는 방법으로 간접적인 분석이라 할 수 있다. 이에 반하여 나노트라이볼로지는 나노크기의 tip을 이용하여 시료 표면을 직접적인 방법으로 분석하여 시료의 형상, 탄성, 강도, 마찰력 등의 정보를 제공하며, tip에의 전기적 신호를 부과하여 시료 표면의 국부적인 potential, electric current를 측정하게 된다. 이에 해당되는 대표적인 분석 장치로는 nano-indenter system과 SPM (Scanning Probe Microscopy)이 있다. 따라서, 이 논문에서는 나노트라이볼로지의 대표적인 장치인 nano-indenter system과 SPM에 대한 간단한 원리를 소개하고 다양한 분야에 대한 실제적인 분석을 사례를 통하여 나노트라이볼로지의 가치를 확인하고자 한다.