• Journal of the Korean Wood Science and Technology
• /
• 제19권2호
• /
• pp.56-64
• /
• 1991

The destructed chips(Pinus rigida Mill) were sulfonated under different conditions and defiberated. The yields and strengths of pulp, fatty acid and resin acid in sulfonated chips were determined. The results of this work were as follows: 1) A sulfonation caused a yield reduction to 97.9~88.2% at single stage. and to 94.9~88.2% at two stage pretreatment. The pulp yields were rapidly draped with increasing cooking temperature from $130^{\circ}C$ to $150^{\circ}C$ 2) Pulp strengths were improved with iacreasing cooking temperature. A sulfonation with 5% $Na_2SO_3$/NaOH(8/2) at single stage and 2% NaOH-5% $Na_2SO_3$ at two stage were most effective and gave the best combination of strength properteis. 3) Fatty acid esters in chips were mostly consisted of palmitic and olleic acid. During a sulfonation the former increased extensively, and the latter was lost with increase of cooking times. The amount of pimaric type in the chips was relatively decreased by the pretreatnent and abietic-type increased. But the changes between two resin acid types were insignificant. 4) The effciency of pitch removal was dependant upon cooking liquor pH. To remove sufficiently the resinous substance, the chips must be sulfonated at over pH 12. Therefore, taking account of pitch removel, two stage sulfonation is considered suitable as reinforcement pulp for newsprint manufacture from pitch pine chips : 2% NaOH($60^{\circ}C$ 1 hr) at first stage and 5% $Na_2SO_3$ ($130^{\circ}C$, 1hr) at secund stage.

• 한국응용과학기술학회지
• /
• 제25권1호
• /
• pp.58-64
• /
• 2008

Pretreatment of eliminating FFA is needed to make biodiesel from animal fat recovered from leather wastes because its acid value is high. This study was carried out to investigate the influence of 4 different pretreatment methods, which are heterogeneous catalyst method, ion exchange resin method, low pressure.high temperature method, and alkali method on the eliminating FFA and fatty acid composition. The results showed that the rate of eliminating FFA increased in the order of alkali method > catalyst method > low pressure high temperature method > ion exchange method. In the case of pretreatment of alkali method using NaOH, the rate of eliminating FFA appeared more than 86% regardless of acid value. Therefore, it was considered that alkali method using NaOH was the most effective in the view of economical and productive aspects, taking it into account that the acid value of animal fat recovered from fleshing scrap generated during leather making processes was 7 to 8.

• 폴리머
• /
• 제25권2호
• /
• pp.302-310
• /
• 2001

무전해도금법을 이용하여 구리/PET 필름 복합재료를 제조하였으며 에칭방법과 촉매액의 조성 및 acceleration 방법을 달리하여 PET 필름과 무전해도금된 구리 피막간의 접착력을 향상시키고자 하였다. HCl 용액으로 에칭된 PET 필름은 NaOH에 의한 것보다 더욱 세밀하게 에칭되어져 구리와 PET 필름간의 접착력은 향상되었으나 전자파 차폐효과는 유사한 경향을 보였다. 촉매액의 조성변화에 따른 영향을 살펴본 결과 PdCl$_2$:SnCl$_2$의 몰비가 1:4에서 1:16으로 증가할수록 PET 필름 위에 적층된 Pd/Sn 콜로이드 입자들의 크기가 감소하며 고르게 분포되는 경향을 보였다. 따라서 이들의 몰비가 증가할수록 구리도금이 균일하고 조밀하게 이루어져 접착력 및 차폐효과가 증가하였다. 또한 NaOH보다 HCl로 acceleration한 경우 촉매 입자의 크기가 작고 더 균일하게 분포되어 우수한 접착력과 도금물성을 나타내었다.

• 한국식품과학회지
• /
• 제32권3호
• /
• pp.720-725
• /
• 2000

여러 가지 처리가 난백의 항원성을 감소시키는데 미치는 영향을 조사하기 위하여, 토끼 항난백항체로 난백 처리물들의 간접 경합 ELISA(ciELISA)를 실시하였다. 식물성, 동물성, 미생물성의 9가지 효소를 이용한 가수분해처리는 난백의 항원성에 영향을 주지 못했다. 보다 효율적인 효소 가수분해를 위해 방사선 조사 후, 효소처리를 실시했는데, 이것 역시 항원성을 감소시키지 못했다. Trifluoromethanesulfonic acid 처리는 난백의 항원성을 거의 제거시키는 것으로 나타났다. 열처리는 $121^{\circ}C$ 고온처리의 경우에서만 반응성이 1/10,000이하로 감소하여 항원성이 거의 사라졌다. NaOH 단독 처리는 0.3%(w/v) 이상의 농도에서 반응성이 감소되기 시작하여, 1%(w/v) 이상에서는 반응성이 1/10,000이하로 감소하였다. NaOH 처리에 $70^{\circ}C$, 15분간의 열처리를 더해 주면, NaOH 단독 처리시보다 효과적으로 항원성이 감소되는 것으로 나타났다.

• Korean Journal of Chemical Engineering
• /
• 제35권11호
• /
• pp.2303-2312
• /
• 2018

Pretreatment process of silica-coated PET fabrics, a major low-grade PET waste, was developed using the reaction with NaOH solution. By destroying the structure of silica coating layer, impurities such as silica and pigment dyes could be removed. The removal of impurity was confirmed by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). The pretreated PET fabric samples were used for depolymerization into its monomer, bis(2-hydroxylethyl) terephthalate (BHET), by glycolysis with ethylene glycol (EG), and zinc acetate (ZnAc) catalyst. The quality of BHET was confirmed by DSC, TGA, HPLC and NMR analyses. The highest BHET yield of 89.23% was obtained from pretreated PET fabrics, while glycolysis with raw PET fabric yielded 85.43%. The BHET yield from untreated silica-coated PET fabrics was 60.39%. The pretreatment process enhances the monomer yield by the removal of impurity and also improves the quality of the monomer.

• 한국염색가공학회지
• /
• 제11권1호
• /
• pp.48-60
• /
• 1999

In this paper, a new regenerated celluosic fiber, "Tencel" was treated with cellulase enzyme. Also Tencel fabrics were pretreated with NaOH and dyed with various reactive dyes, and subsequently finished with DMDHEU. $\Delta{E}^*_{ab}$ value was calculated by measuring color difference before and after wet abrasion test to rubbing. The fibrillation propensity was estimated on Tencel by means of weight loss, $\Delta{E}^*_{ab}$ value, and SEM observation. Weight loss of NaOH pretreated Tencel fabric is more lower than that of original fabric. The cellulase treatment decreased tensile strength but improved wet abrasion strength, wrinkle recovery, and bending properties. Tendency of fibrillation for Tencel fabric was reduced by NaOH-pretreatment, dyeing with multifunctional reactive dyes, and afterfinishing by DMDHEU.by DMDHEU.

• 한국지반환경공학회 논문집
• /
• 제15권10호
• /
• pp.15-21
• /
• 2014

본 연구는 부산시 남부하수처리장의 탈수슬러지를 이용하여 전처리에 따른 분해 및 혐기성 상태에서의 최종 메탄 및 이산화탄소 발생량을 평가하기 위해 Biochemical Methane Potential(BMP) 실험을 실시하였다. 초기 1 % TS 농도의 탈수슬러지를 각각 30분 동안 5M NaOH를 이용하여 알칼리 전처리를 실시하였고 초음파 전처리는 30분 동안 조사밀도를 1.5 W/mL로 조절하여 실시하였으며 알칼리와 초음파 전처리를 병합한 동시 전처리를 시행하였다. 그에 따라 SCOD 값이 초기 33.1 mg/L에서 최대 494 mg/L로 증가하였다. 또한 BMP 실험을 실시한 결과 31.2~84.2 mL $CH_4/g$ VS, 9.2~13.5 mL $CO_2/g$ VS로 나타났다. 영양배지와 상등액 슬러지를 주입여부에 따른 BMP 실험을 실시한 결과 각각 73.1, 73.8 mL $CH_4/g$ VS, 11.2, 13.6 mL $CO_2/g$ VS으로 나타났으며 모델값과는 큰 차이를 보이지 않았다. BMP 실험을 종료 후 VS를 분석한 결과 초기 62 %에서 33.8~45.4 %로 감소하였다. 알칼리, 초음파 전처리보다는 동시 전처리가 메탄발생량과 SCOD 값을 증가시켰으며 VS 감소율이 증가하여 혐기성 소화율이 향상되었다.

• 에너지공학
• /
• 제20권2호
• /
• pp.84-89
• /
• 2011

본 연구는 하수슬러지에 알칼리처리와 초음파처리를 적용하여 최적의 가용화 조건을 도출하고자 각각의 단일처리, 병합처리로 가용화율을 확인하였다. 단일처리 중 알칼리처리는 4종의 알칼리시약을 각각 적용하여 전처리한 결과, NaOH를 이용한 방법이 27.6%로 가장 높은 가용화율을 확인할 수 있었으며, 주입농도가 높아지더라도 가용화에 미치는 영향에는 한계가 있음을 확인하였다. 초음파처리는 140 W/L의 조사밀도에서 가용화율이 가장 높았으며(33~39%), 조사주기의 증대는 가용화율에 큰 영향을 미치지 않는 것으로 확인되었다. 알칼리 처리와 초음파처리를 혼재한 병합처리 시 알칼리처리 후 초음파처리를 적용한 방법이 $70.4{\pm}9.4%$의 가용화율로 초음파처리 후 알칼리처리 방법에 비해 약 22% 높은 결과를 나타내었다. 각 조건에서의 SCOD 증가속도는 병합처리(알칼리처리 후 초음파처리)에서 0.076 $min^{-1}$으로 가장 높은 결과를 나타내었다.

• 산업기술연구
• /
• 제27권A호
• /
• pp.195-202
• /
• 2007

Milled Korean pine (Pinus densiflora) wood was used to evaluate its adsorption capacity of Cu(II) ions from aqueous solution by running a series of batch experiments. Prior to the tests, the milled woods were pretreated with 1N NaOH, 1N $HNO_3$, and distilled water, respectively, to examine the effect of pretreatment. Within the tested pH range between 3 and 6, copper adsorption efficiency of NaOH-treated wood(96~99%) was superior to the $HNO_3$-treated wood(19~31%) and distilled water-treated wood(18~35%). The efficiency of copper removal by wood enhanced with increasing solution pH and reached a maximum copper ion uptake at pH 5~6. Adsorption behavior of copper onto both raw and $HNO_3$-treated woods was mainly attributed to interaction with carboxylic acid group. For NaOH-treated wood, carboxylate ion produced by hydrolysis or saponification was a major functional group responsible for Cu sorption. NaOH treatment of wood changed the ester and carboxylic acid groups into carboxylate group, whereas $HNO_3$ treatment did not affect the production of functional groups which could bind copper. A pseudo second-order kinetic model fitted well for the sorption of copper ion onto NaOH-treated wood. A batch isotherm test using NaOH-treated wood showed that equilibrium sorption data were better represented by the Langmuir model than the Freundlich model.

• 한국환경보건학회지
• /
• 제40권2호
• /
• pp.147-156
• /
• 2014

Objectives: This study was carried out to examine whether the apparent photolysis with or without sensitizers [NaOH and humic acid (HA)] was prompted photodegradation of polychlorinated biphenyl (PCB) in aqueous solution. Methods: PCBs photodegradation occurred using fluorescence black lamps at ${\lambda}_{max}=300nm$. PCB congeners were exposed in 10 ppm HA or 0.05N NaOH solutions, to investigate the decreasing profile of PCB concentration with time. The PCBs were then analyzed by gas chromatography/mass spectrometry (GC-MS). Reductive degradation profile of PCB congeners in the presence of both sensitizers under oxygen-saturated protic conditions was described using the wind-rose diagrams. Results: Use of HA or NaOH decreased PCB concentration with time in the dark and on irradiation, indicating that photolysis underwent through reductive dechlorination through energy transfer and possibly with reactive oxygens. The dechlorination was marked by a chromatographic shift, observed in the GC-MS plots. Therefore it is logical to assume that increasing the dose of sensitizers would increase the photodegradation rates of PCBs. The half-lives of pentachloro-PCB (penta-3) in 0.05N NaOH and 10 ppm HA were estimated at about 47 hours and 39 hours, respectively, under the same experimental conditions of photolysis. It was found that the rate of photolysis of pentachloro-PCB in aqueous solution followed apparent first-order kinetics compared to other congeners. Conclusion: Photochemical degradation (using 328 nm UV light) of penta- and hexa-PCBs in HA or alkaline solution is a viable method for pretreatment method. The results are helpful for the further comprehension of the reaction mechanism for photolytic dechlorination of PCBs in aquatic system.