• Journal of Sensor Science and Technology
• /
• v.15 no.1
• /
• pp.65-70
• /
• 2006

Characteristics of thin-film NTC thermal sensors fabricated by micromachining technology were studied as a function of the thickness of membrane. The overall-structure of thermal sensor has a form of Au/Ti/NTC/$SiO_{X}$/(100)Si. NTC film of $Mn_{1.5}CoNi_{0.5}O_{4}$ with 0.5 mm in thickness was deposited on $SiO_{X}$ layer (1.2 mm) by PLD (pulsed laser deposition) and annealed at 873-1073 K in air for 1 hour. Au(200 nm)/Ti(100 nm) electrode was coated on NTC film by dc sputtering. By the results of microstructure, X-ray and NTC analysis, post-annealed NTC films at 973 K for 1 hour showed the best characteristics as NTC thermal sensing film. In order to reduce the thermal mass and thermal time constant of sensor, the sensing element was built-up on a thin membrane with the thickness of 20-65 mm. Sensors with thin sensing membrane showed the good detecting characteristics.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.5
• /
• pp.218-227
• /
• 2021

A thick film NTC thermistor for low temperature co-firing was manufactured by printing and sintering a paste prepared using NTC powder of Mn_1.5Ni_0.4Co_0.9Cu_0.4O₄ composition, lead free frit, and RuO₂ on a 96 % alumina substrate. The effect of frit and RuO₂ on the electrical properties of thick film NTC thermistor was studied. The resistance of the thick film NTC thermistor was higher than that of the bulk phase sintered at the same temperature, but it was found that the negative resistance temperature characteristic appeared more clearly and linearly in the resistance - temperature characteristic. On the other hand, the area resistance decreased as the sintering temperature increased, and the area resistance increased as the amount of frit added increased. The B constant of the thick film NTC thermistor was 3000 K or higher. Among them, it was found that the B constant of the thick film NTC thermistor made of paste with 5 wt% of frit added and sintered at 900℃ showed the highest B constant. Also, it can be seen that the area resistance decreased with the addition of RuO₂, and the change in the area resistance decrease of the thick film NTC thermistor obtained by sintering the paste containing 5 wt% of RuO₂ at 900℃ is the most obvious.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.1
• /
• pp.28-37
• /
• 2018

In order to study the NTC thermistor that can be fired at low temperature, the influence of the lead free glass frit and $RuO_2$ addition on the electrical properties of the NTC thermistor of $Mn_{1.85}Ni_{0.25}Co_{0.9}O_4$ basic composition was studied. The sintering characteristics of the specimen sintered at $1000^{\circ}C$ with 10 wt% frit added to the basic NTC composition were similar to those of the specimen sintered at $1200^{\circ}C$ without frit. However, as the amount of frit increased, the electrical resistivity and B constant were increased. In order to reduce the resistance, NTC thermistor was prepared by adding 0, 2, and 5 wt% of $RuO_2$ to the composition containing 10 wt% of frit and sintered at $1000{\sim}1200^{\circ}C$, and sintering and electrical properties were measured. The electrical resistivity and the B constant tended to decrease with increasing $RuO_2$ content. However, the resistivity was the lowest at sintering temperature of $1000^{\circ}C$ and the resistance increased with increasing sintering temperature after 5 wt% $RuO_2$ addition. The NTC thermistor sintered at $1000^{\circ}C$ with 10 wt% frit and 5 wt% $RuO_2$ in the composition of NTC showed similar electrical properties and sintering characteristics when sintered at $1200^{\circ}C$ without added frit.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.866-869
• /
• 2015

With the advance in semiconductor technology, the number of elements that can be integrated in system-on-chip(SoC) increases exponentially, and thus voltage scaling is indispensable to enhance energy efficiency. Near-threshold voltage computing(NTC) improves the energy efficiency by an order of degree, hence it is able to overcome the limitation of conventional super-threshold voltage computing(STC). Although NTC-based low performance manycore system can be used to maximize energy efficiency, it demands more number of cores to sustain the performance, which results in considerable increase of area. In this paper, we analyze NTC manycore architecture considering the trade-offs between performance, power, and area. Therefore, we propose an algorithmic methodology that can optimize power consumption and area while satisfying the required performance by determining the constrained number of cores and size of caches and clusters in NTC environment. Experimental results show that proposed NTC architecture can reduce power consumption by approximately 16.5 % while maintaining the performance of STC core under area constraint.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.459-462
• /
• 2001

Interface effects on properties of NTC thermistors having Mn-Co-O spinel crystal structure system are analyzed by a mixing rule in case of mixed types and layered types between CuO and Al$_2$O$_3$ added compounds. With adding CuO and Al$_2$O$_3$, The compounds form completely solid solution and their resistance and B constant are changed due to the variation of conduction electrons by their ionic substitutions. The properties of mixed NTC thermistors are depended on the logarithmic mixing rule by a dispersed phase and they show slightly lower values due to the lattice mixing affect in compared with calculated values. The resistance of layered NTC thermistors is depended upon the series mixing rule containing the value of an interface layer and effected by the variation of its thickness, and it is changed rapidly to the logarithmic mixing rule by the connection between two layers with increasing the interface layer

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.2
• /
• pp.88-92
• /
• 2003

The correlationship between heat treatment condition and electrical properties of the Mn-Co-Ni oxide NTC thermistor for fuel level sensor was investigated by the X-ray diffractometry, density measurement, and electrical properties measurement such as resistivity, B constant, and thermal dissipation constant. It was shown that the heat treatment of NTC thermistor was responsible for sinterability of Mn-Co-Ni oxide. The highest density of 5.10 g/㎤ was obtained at $1250^{\circ}C$, 2 hours, at which the densification was almost completed. This is also manifested from the microstructural observation. It is found that the electrical resistivity and B constant are increased at the elevated sintering temperatures. The NTC specimens prepared in this study showed the conventional decrease of resistance with the measured temperature and the linear behavior of output voltage with fuel levels. Therefore, the electrical properties of thermistor were closely correlated with sintering condition. and the Mn-Co-Ni oxide thermistor prepared in this study has a great possibility enough to apply for an automobile fuel level sensor.

• Journal of the Korean Ceramic Society
• /
• v.40 no.1
• /
• pp.11-17
• /
• 2003

The effect of$ZrO_2$addition on the microstructure and electrical properties of Ni-Mn oxide NTC thermistors was studied. Major phases present in the sintered bodies of $Ni_{1.0}Mn_{2-x}Zr_xO_4$ were the solid solutions of Ni-Mn-Zr oxides with a cubic spinel structure and the $ZrO_2$ with a tetragonal structure. The $ZrO_2$ was formed by the partial decomposition or incomplete formation of the Ni-Mn-Zr oxides during sintering. With increasing the amount of added $ZrO_2$, the $ZrO_2$ phase increased. The relationship between log resistivity (log p) and the reciprocal of absolute temperature (1/T) of the NTC thermistors prepared was linear, indicative of NTC characteristics. The resistivity, B constant and activation energy of the thermistors increased with increasing $ZrO_2$ content.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.391-396
• /
• 2001

In order to estimate thermal cracking in mass concrete and to decide the removal time of the forms outside the concrete structures in wintertime, temperature measurement is indispensible. Until now, the measurement system employs thermocouple type. In this paper, we introduce economical and accurate NTC(Negative Temperature Coefficient) ceramic type measurement system. In principle, NTC ceramic type sensor is very sensitive in the range -20~15$0^{\circ}C$. In this range, the signal change is so large that the sensor needs less amplification than thermocouple. Therefore, not only the sensor itself is inexpensive but also the system is too. In this experiments the temperature of the NTC system are identical to those of thermocouple. In conclusion, inexpensive NTC thermistor system is very adequate to the temperature measurement during concrete curing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.546-551
• /
• 1998

$Mn{1-X}Fe{2+X}O_4, Mg_{1-X}Fe_{2+X}O_4$ (x=0.0, 0.025, 0.1, 0.2) for negative temperature coefficient (NTC) thermistor was prepared by calcination at $800^{\circ}C$ and sintering at form 1100 to $1250^{\circ}C$ with $50^{\circ}C$ intervals. The best linear property was obtained in the Mn-based sample sintered at $1200^{\circ}C$ with x=0.0 composition. Temperature coefficient of resistance, $\alpha$, was $-5.6%/^{\circ}C$ in the Mn-based sample, $-5.2%/^{\circ}C$ in the MM-based sample, and $-1.6%/^{\circ}C$ in the Mg-based sample. thermistor parameter, B, was in the range of 2665~7780 K. The results show the possibility that Mn-Ni-Co based thermistor could be substituted by the composition used in this study.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.459-462
• /
• 2001

Interface effects on properties of NTC thermistors having Mn-Co-O spinel crytal structure system are analyzed by a mixing rule in case of mixed types and layered types between CuO and $Al_{2}O_{3}$ added compounds. With adding CuO and $Al_{2}O_{3}$, The compounds form completely solid solution and their resistance and B constant are changed due to the variation of conduction electrons by their ionic substitutions. The properties of mixed NTC thermistors are depended on the logarithmic mixing rule by a dispersed phase and they show slightly lower values due to the lattice mixing affect in compared with calculated values. The resistance of layered NTC thennistors is depended upon the series mixing rule containing the value of an interface layer and effected by the variation of its thickness, and it is changed rapidly to the logarithmic mixing rule by the connection between two layers with increasing the interface layer.