• 한국연소학회지
• /
• 제10권2호
• /
• pp.26-34
• /
• 2005

The performance of oxygen combustion with $CO_2$ feeding was investigated in a pyrex tube furnace. The inverse type multi-hole burner was used for improving mixing and wide operating range. It introduced oxygen, fuel, and oxygen, respectively, from center tube to outer tubes. Oxygen combustion characteristics with excess oxygen ratio, oxygen feeding ratio, and $CO_2$ feeding flow rate were studied to optimize the operating condition and to apply the oxygen combustion with recirculation of flue gas to a real furnace. This paper presents results on the effect of $CO_2$ feeding flow rate on the structure of the flames and concentrations of NO and CO emissions. The visible flame length was shortest due to well mixing between fuel and oxygen when the oxygen feeding ratio was 0.25. The NO emission was reduced drastically regardless of excess oxygen ratio when the $CO_2$ feeding flow rate was larger than 15 lpm. The CO emission is varied by changing the $CO_2$ feeding flow rate but the CO emission characteristics is highly affected by excess oxygen ratio. When the excess oxygen ratio is below $\lambda=1.1$, the CO emission increased as the $CO_2$ feeding flow rate increased.

• 대한환경공학회지
• /
• 제30권5호
• /
• pp.552-559
• /
• 2008

접선 연소식 미분탄 보일러의 연소특성 분석을 위한 3차원 전산해석 연구를 수행하였다. 해석 결과의 건전성 검증을 위하여 보일러 출구, 즉 절탄기 후단에서의 가스 온도, O$_2$, NO, CO 농도를 발전소의 실제 측정 결과와 비교하였다. 실제 발전소의 운전조건을 기준으로 보일러내의 가스온도, 속도 분포를 해석하였으며 주요 가스농도인 O$_2$, CO, CO$_2$, NO의 분포와 char 입자 궤적을 구하였다. 본 연구를 통하여 최종과열기 전단에서의 가스 온도가 불균일하게 분포함을 알 수 있었으며, 이는 보일러 상부 연소로에서의 잔류 선회유동의 결과인 것으로 파악되었다. 불균일한 가스온도 분포에 대한 해석결과는 접선연소식 미분탄 보일러에서 자주 발생하는 튜브 파손을 방지하는데 있어 유용한 자료로 활용될 수 있을 것이다.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.8-14
• /
• 2007

Compression ignition of homogeneous charges in IC engines indicates possibilities of achieving the high efficiency of DI diesel engines with low level of NOx and particulate emissions. The objectives of this study are to further understand the characteristics of the HCCI(Homogeneous charge compression ignition) combustion and to find ways of extending the rich HCCI operation limit in an engine-like environment. DME fuel is supplied either in the form of premixture with air or directly injected in the combustion chamber of a rapid compression and expansion machine under the conditions of various equivalence ratio and injection timing. The cylinder pressure is measured and the rate of heat release is computed from the measured pressure for the analysis of the combustion characteristics. The experimental data show that the RCEM can operate without knock on mixtures of higher equivalence ratio, when DME is directly injected in the combustion chamber than introduced as a fraction of a perfect or nearly perfect premixture. Very early fuel injection timings usually employed in HCCI operation are seen to have only insignificant effects in control of ignition timing.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.22-27
• /
• 2007

Our environment is faced with serious problems related to the air pollution from automobiles in these days. In particular, the exhaust emissions of diesel engines are recognized as main causes of the air pollution. CRDI(common rail direct injection) diesel engine is widely used for the sake of minimization on exhaust emission. Because biodiesel fuel is a renewable and alternative fuel for diesel engine, its usability is expanded. In this study, a common rail diesel engine was run with 5% of biodiesel fuel(BDF 5%) more than 150 hours. Engine dynamometer testing was completed at regularly scheduled intervals to investigate the engine performance and exhaust emissions. The data of engine performance and exhaust emissions was sampled at 1 hour intervals for analysis. When a common rail diesel engine runs on BDF 5% for long time, power and energy consumption of the engine are similar to the case using diesel fuel. The smoke emission of BDF 5% was reduced in comparison with diesel fuel, that is, it was reduced approximately 15% at 4000rpm, and load of 90%. And, CO and $CO_2$ were reduced, too. On the other hand, NOx emission of biodiesel fuel was slightly increased about 2%, but it was almost same as a commercial diesel fuel.

• 한국자동차공학회논문집
• /
• 제20권4호
• /
• pp.125-132
• /
• 2012

Urea-SCR system, which converts nitrogen oxides to nitrogen and water in the presence of a reducing agent, usually AdBlue urea solution, is known as one of the powerful NOx reduction systems for mobile as well as stationary applications. For its consistent and reliable operation in mobile applications, such various problems as transient injection, ammonia slip, and freezing in cold weather have to be resolved. In this work, therefore, numerical study on three-dimensional unsteady heating problems were analyzed to understand the melting and heat transfer characteristics such as urea liquid volume fraction, temperature profiles and generated natural convection behavior in urea solution by using the commercial software Fluent 6.3. After validating by comparing numerical and experimental data with pure gallium melting phenomena, numerical experiment for urea melting is conducted with three different coolant heating models named CH1, 2, and 3, respectively. Finally, it can be found that the CH3 model, in which more coolant is concentrated on the lower part of the urea tank, has relatively better melting capability than others in terms of urea quantity of $1{\ell}$ for start-up schedule.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.1-7
• /
• 2007

The effect of injector geometries including the injection angle and number of nozzle holes on homogeneous charge compression ignition (HCCI) engine combustion has been investigated in an automotive-size single-cylinder diesel engine. The HCCI engine has advantages of simultaneous reduction of PM and NOx emissions by achieving the spatially homogenous distribution of diesel fuel and air mixture, which results in no fuel-rich zones and low combustion temperature. To make homogeneous mixture in a direct-injection diesel engine, the fuel is injected at early timing. The early injection guarantees long ignition delay period resulting in long mixing period to form a homogeneous mixture. The wall-impingement of the diesel spray is a serious problem in this type of application. The impingement occurs due to the low in-cylinder density and temperature as the spray penetrates too deep into the combustion chamber. A hole-type injector (5 holes) with smaller angle ($100^{\circ}$) than the conventional one ($150^{\circ}$) was applied to resolve this problem. The multi-hole injector (14 holes) was also tested to maximize the atomization of diesel fuel. The macroscopic spray structure was visualized in a spray chamber, and the spray penetration was analyzed. Moreover, the effect of injector geometries on the power output and exhaust gases was tested in a single-cylinder diesel engine. Results showed that the small injection angle minimizes the wall-impingement of diesel fuel that results in high power output and low PM emission. The multi-hole injector could not decrease the spray penetration at low in-cylinder pressure and temperature, but still showed the advantages in atomization and premixing.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.64-71
• /
• 2013

In this study we designed a lean $NO_x$ trap (LNT) model with $GT-POWER^{TM}$ program and then the LNT model was compared to the bench flow reactor test results. This model consists of 9 kinetic reactions to represent the main steps of NO oxidation, $NO_x$ adsorption, $NO_x$ release and then its reduction. The comparison was performed on the operating conditions at the space velocity of 50,000 1/hr and 80,000 1/hr with the temperature range of $200^{\circ}C{\sim}500^{\circ}C$ with the even spaced temperature step of $50^{\circ}C$. The experimental results show that the $NO_x$ conversion efficiency was enhanced by the temperature up to $350^{\circ}C$ and then decayed at higher temperatures. The LNT model predicts the similar trend of the $NO_x$ conversion efficiency to the experimental results below $350^{\circ}C$, but overestimates above $350^{\circ}C$. This overestimation comes from the higher reduction efficiency which was obtained by the different reduction gas composition such as $C_3H_6$ in the model to replace $CH_4$, $C_2H_4$ in the bench test.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.287-296
• /
• 2017

Although emission regulations have been gradually strengthened in the past decade, the road transport section remains the most important source of NOx emission in air pollution. One reason is that there has been an increase in the proportion of diesel vehicles and in the volume of traffic. In addition, the certification procedure for standard emission limit does not sufficiently reflect real traffic condition and various driving patterns. Therefore, the European Commission(EC) has recently come up with the RDE-LDV(Real driving emissions-light duty vehicle) regulations, and the Ministry of Environment in Korea has been conducting research on evaluating RDE-LDV with PEMS(Portable Emission Measurement Systems). According to the trip requirements of the 2nd RDE package announced by the EC, the objectives of the present study include the development of Korean RDE routes to reflect domestic traffic and road conditions. Based on the results, both RDE routes are in correct compliance with RDE-LDV regulations, including trip requirements and trip dynamics. KOR-NIER Route 1, in particular, has a higher driving load in rural driving with regard to excessive gradient of elevation compared to KOR-NIER Route 2, including relatively plane rural driving.

• 수산해양기술연구
• /
• 제53권1호
• /
• pp.89-97
• /
• 2017

Butanol has an ability to improve the ignition quality due to its lower latent heat of vaporization; it has an advantage to reduce a volume of a fuel tank because its energy density is higher than that of ethanol. Also, butanol-diesel oil blending quality is good because butanol has an effect to prevent the phase-separation between two fuels. Even if the blended oil contains water, it can reduce the corrosion of the fuel line. Thus, it is possible to use butanol-diesel oil blended fuel in diesel engine without modification, and it may reduce the environment pollution due to NOx and particulate and the consumption of diesel oil. Therefore, some studies are being advanced whether butanol is adequate as an alternative fuel for diesel engines, and the results of the combustion and exhaust gas emission characteristics are being presented. Though the injection and spray characteristics of butanol are more important in diesel combustion, the has not yet dealt with the matter. In this study, the influence in which differences of physical properties between butanol and diesel oil may affect the injection and spray characteristics such as injection rate, penetration, spray cone angle, spray velocity and process of spray development were examined by using CRDI system, injection rate measuring device and spray visualization system. The results exhibited that the injection and macroscopic spray characteristics of two fuels were nearly the same.

• 한국가스학회지
• /
• 제22권2호
• /
• pp.84-89
• /
• 2018

최근 환경문제로 인해 폭발성 폐기물을 안전하게 소각 처리하는 방법에 대한 연구가 활발히 진행되고 있다. 유동층 소각로를 이용한 처리 공정은 기존 방법보다 연소 가스 배출량이 현저하게 낮으며, 운전의 효율 또한 높다. 본 연구에서는, 폐 추진제 중 가장 많은 양이 폐기되고 있는 Double-based Propellant를 유동층 소각로에서 소각하는 공정을 전산유체역학 프로그램으로 모사하였다. Cylindrical Bed 내부에서 일어나는 7개의 연소 반응이 안전하게 모사되는 것을 확인하였다. 이를 바탕으로 실제 공정 설계를 진행하면, 앞으로 폭발성 폐기물 처리 공정 연구에 새로운 연구 방향을 제시할 것이라 사료된다.