• 제목/요약/키워드: ND4

검색결과 5,022건 처리시간 0.042초

반도체 레이저 측면 여기 Nd:YAG 매질에서의 열영향 (Thermal effect at Nd:YAG using a laser-diode side-pumping)

  • 양동옥;김병태
    • 한국광학회지
    • /
    • 제14권1호
    • /
    • pp.44-50
    • /
    • 2003
  • 반도체 레이저 측면 여기시 Nd:YAG 레이저 매질에서 발생하는 열영향에 대해 분석하였다. 열영향을 고감도로 측정하기 위해 편광자와 Nd:YAG 매질 사이에 λ/4판을 삽입하여 여기 파워에 따라 발생하는 depolarization양을 측정하였다. CCD로 는 열영향에 의한 매질 내에서의 탐침광 분포 변화를 측정하고 해석하여 반도체 레이저 측면 여기시 발생하는 열영향을 최소화하기 위한 공진기 설계의 효과적인 방법을 제시하였다.

연속 발진 다이오드 레이저로 여기된 수동형 Q-스위치 Nd:YVO4 레이저의 출력 펄스 안정화 (Stabilization of Output Pulses from a Passively Q-switched Nd:YVO4 Laser Pumped by a Continuous-wave Laser Diode)

  • 안승인;박윤배;여환섭;이준호;이강인;이종훈
    • 한국광학회지
    • /
    • 제20권5호
    • /
    • pp.276-280
    • /
    • 2009
  • Cr:YAG 결정을 포화흡수체로 사용하여 수동형 Q-스위치시킨 다이오드 레이저 여기 Nd:$YVO_4$ 레이저를 제작하였다. Cr:YAG 결정의 한 면에 여기 빛 파장(808 nm)에 대해 고반사 코팅을 한 후, Nd:$YVO_4$ 결정과 접촉시켜 공진기를 구성하였다. Cr:YAG의 한 면에 여기 다이오드 레이저를 반사시키는 코팅을 입혀 공진기의 광변환 효율을 높임과 동시에, 여기빔에 의한 포화흡수체의 표백현상을 방지하여 안정된 출력이 나오게 하였다. 레이저 이득 매질 및 포화흡수체의 온도는 열전 냉각기와 냉각수를 사용하여 안정화 시켰다. 온도안정화를 시킨 상태에서 발진되는 펄스의 첨두 출력 요동(peak to peak)은 4%였다. 다이오드 레이저의 출력이 1 W일 때, 출력 펄스의 반복률은 평균 9 KHz 였으며, 최소 펄스폭은 7.11 ns, 최고 출력은 16.27 mW였다.

액상구비의 시용시기가 오차드그라스의 건물수량에 미치는 영향 (The Effect of Application Times of Cattle Slurry on Dry Matter Yield in Orchardgrass)

  • 조익환;전하준
    • 한국유기농업학회지
    • /
    • 제6권1호
    • /
    • pp.99-108
    • /
    • 1997
  • The aim of this experiment was to investigate the effect of applying times of cattle slurry on dry matter yield of Orchardgrass, when cattle slurry applied at rates of 30m3(average mineral nitrogen fertilizer equivalent to 120kg) per ㏊ in different dressing times, such as S1(1st and 2nd growth), S2(1st and 3rd growth), S3(1st and 4th growth), S4(2nd and 3rd growth), S5(2nd and 4th growth) and S6(application for 3rd and 4th growth). The results were as follows. 1. The average annual yields of dry matter were produced 6.36~7.42 ton per ㏊ in 1995~1997 when cattle slurry applied at rates of 30m3(average mineral nitrogen fertilizer equivalent to 120kg) per ㏊ in different dressing times, especially these tendency were shown higher annual dry matter in S4 plot9application for 2nd and 3rd growth). Those were higher 2.48~3.54 tons or 1.22~2.28 tons per ㏊ than the yields from non-fertilizing or phosphrous and potassium fertilizing. 2. Relative yields of annual dry matter in cattle slurry application plots were 164(S2 plot)~191(S4 plot)% in comparing with non-fertilizing plot. 3. Dry matter yields according to cutting frequency were highest at the 2nd cut(1.50 ton) and were in the order 3rd cut(0.95 ton)>4th cut(0.75 ton)>1st cut(0.69 ton/㏊). Also, those of cattle slurry application plot per ㏊ were in the order 2nd cut(2.02~2.73 tons)>3rd cut(1.56~2.08 tons)>4th cut(1.07~1.68 tons)>1st cut(1.11~1.45 tons/㏊). 4. Relative yields of annual dry matter in cattle slurry application plots were 164~219, 161~210, 143~212 and 135~182% at the 3rd, 1st, 4th and 2nd cut, respectively in comparing with non-fertilizing plot. 5. The efficiencies of nitrogen on dry matter yield(kg DM/kg N) were 18.1, 21.3 and 34.5kg DM/kg N when cattle slurry applied to Orchardgrass at rates of 30m3 (average mineral fertilizer equivalent to 120 kg) per ㏊ in 1993, 1994 and 1995, respectively, especially these tendency were shown higher efficiencies in S4 plot(application for 2nd 3rd growth). On the other hand, those of the same level fertilization of mineral nitrogen were 43.8, 19.2 and 13.4 kg DM/kg N in 1993, 1994 and 1995, respectively.

  • PDF

식품중의 오염물질에 관한 조사연구 (Monitoring Program on Food Contaminants)

  • 백덕우
    • 한국식품위생안전성학회지
    • /
    • 제2권3호
    • /
    • pp.121-136
    • /
    • 1987
  • 본 연구는 1983년부터 시작한 농작물중의 잔류농약 Monitoring program으로서 우리나라의 농작물중의 농약잔류량을 파악하고 이를 기초자료 (back data)로 우리나라 실정에 맞는 농작물중의 잔류농약허용량을 선정하기 위하여 시행되었다. 금년도에는 86년도의 대상농약인 유기인제 (8종), 카바메이트제(3종)에 유기염소제 살균제인 Captan, Captafol을 추가하였으며 대상식품으로 상치, 무우, 감자, 파, 감, 고구마를 예년도의 대상식품이었던 도마도, 풋고추, 사과, 복숭아, 콩, 오이, 배추중에는 Captan, Captafol을 경기, 충남, 경북, 전북의 4개 지역에서 채취하여 G.C.-NPD, ECD를 사용하여 그 잔류량을 조사한 결과 다음과 같다. 1. Diazinon은 32.0%의 검출율을 보였고 검출범위는 ND∼0.0872ppm, 평균은 0.0020ppm이었다. 2. Fenthion(MPP)는 16.4%의 검출율을 보였고 검출범위는 ND∼0.0395ppm, 평균은 0.0007ppm이었다. 상치, 가지, 고구마에서는 검출되지 않았다. 3. Fenitrothion(MEP)는 30.5%의 검출율을 보였고 검출범위는 ND∼0.0628ppm이었고 평균 0.0026ppm이었다. 4. Phenthoate(PAP)는 7.0%의 검출율을 보였고 검출범위는 ND∼0.0069ppm, 평균 0.0001ppm이었다. 감자, 가지, 감, 고구마에서는 검출되지 않았다. 5. EPN은 13.3%의 검출율을 보였고 검출범위는 ND∼0.0250ppm, 평균은 0.0030ppm이었다. 감자에서는 검출되지 않았다. 6. Dimethoate는 27.3%의 검출율을 보였으며 검출범위는 ND∼0.0826ppm, 평균은 0.0049ppm이었다. 7. Parathion은 22.7%의 검출율을 보였으며 검출범위는 ND∼0.0771ppm, 평균 0.0021ppm이었다. 김, 고구마에서는 검출되지 않았다. 8. Malathion은 10.9%의 검출율을 보였으며 검출범위는 ND∼0.0098ppm, 평균 0.0001ppm이었다. 상치, 무우에서만 검출되었다. 9. Carbaryl(NAC)은 6.3%의 검출율을 보였고 검출범위는 ND∼0.8452ppm, 평균은 0.0336ppm이었다. 상치와 쑥갓에서만 검출되었다. 10. Isoprocarb(MIPC)는 31.3%의 검출율을 보였고 검출범위는 ND∼0.1180ppm, 평균 0.0104ppm이었다. 11. BPMC는 22.7%의 검출율을 보였고 검출범위는 ND∼0.5106ppm, 평균 0.0085ppm이었다. 12. Captan은 58.7%의 검출율을 보였고 검출범위는 ND∼0.1970ppm, 평균은 0.005ppm이었다. 13. Captafol은 2.3%의 검출율을 보였고 검출범위는 ND∼0.0312ppm, 평균은 0.0003ppm이었다. Captafol은 파에서만 검출되었다.

  • PDF

MOS 구조에서 실리사이드 형성단계의 공정특성 분석 (Analysis on Proecwss Characteristics of 2'nd Silicidation Formation Process at MOS Structure)

  • 엄금용
    • 한국전기전자재료학회:학술대회논문집
    • /
    • 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
    • /
    • pp.130-131
    • /
    • 2005
  • In the era of submicron devices, super ultra thin gate oxide characteristics are required. Titanium silicide process has studied gate oxide reliability and dielectric strength characteristics as the composition of gate electrode. In this study the author observed process characteristics on MOS structure. In view point of the process characteristics of MOS capacitor, the oxygen & Ti, Si2 was analyzed by SIMS analysis on before and after annealing with 1,2 step silicidation, the Ti contents[Count/sec]of $9.5{\times}1018$ & $6.5{\times}1018$ on before and after 2'nd anneal. The oxygen contents[Count/sec] of $4.3{\times}104$ & $3.65{\times}104$, the Si contents[Count/sec] of $4.2{\times}104$ & $3.7{\times}104$ on before and after 2'nd anneal. The rms value[A] was 4.98, & 4.03 on before and after 2'nd anneal.

  • PDF

Growth of $GdVO_4$ composite single-crystal rods by the double-die edge-defined film-fed growth technique

  • Furukawa, Y.;Matsukura, M.;Nakamura, O.;Miyamoto, A.
    • 한국결정성장학회지
    • /
    • 제18권1호
    • /
    • pp.1-4
    • /
    • 2008
  • The growth of composite-structured Nd:$GdVO_4$ single crystal rods by the double die EFG method is reported. Two crucibles are combined with an outer and inner die for ascending of different melt. The composite-structured Nd:$GdVO_4$ single crystal rods with a length of 50 mm and an outer diameter of 5 mm including of inner Nd-doped core region with diameter 3 mm were grown successfully. Nd distribution in the, radial direction has graded profile from result of EPMA. Absorption coefficient in the core region at 808 nm was $42cm^{-1}$. Finally, we demonstrated the laser oscillation using our composite crystal and 2-W output was obtained.

레이더 펄스 탐지를 위한 통신 전자파잡음 동적제거 기법 (Communication Noise Dynamic Cancellation Method for Radar Pulse Detection)

  • 정운섭;이치헌;최채택;최승호
    • 한국정보처리학회:학술대회논문집
    • /
    • 한국정보처리학회 2012년도 추계학술발표대회
    • /
    • pp.732-735
    • /
    • 2012
  • 본 논문은 지상에서 발생하는 전자파 잡음 신호의 유입에 의해 많은 영향을 받을 수 있는 헬기 등 항공기의 레이더경보수신기(Radar Warning Receiver)에서도 레이더 펄스 신호를 탐지할 수 있는 통신전자파잡음 동적제거 기법을 제안하였다. 본 논문은 지상의 노이즈 신호를 분류하는 방법을 제시하였고, 노이즈 신호 레벨을 판단하여 효과적으로 잡음을 제거하는 알고리즘을 제안하였다.

$(Nd_{1-x}R_x)_2Fe_{14}B$ (R=Y, Pr)의 자기특성 (Magnetic properties of $(Nd_{1-x}R_x)_2Fe_{14}B$ (R=Y, Pr))

  • 김만중;김윤배;김희태;김택기
    • 한국자기학회지
    • /
    • 제8권5호
    • /
    • pp.271-274
    • /
    • 1998
  • 자장중 정렬된(Nd1-xRx)2Fe14B (R=Y, Pr) 다결정 분말을 사용하여 스핀재배열현상과 결정자기이방성을 연구하였다. 이 화합물에서 스핀재배열온도(TSR)는 R=Pr인 경우 0$\leq$x$\leq$0.75 의 조성범위에서 Pr 치환량이 증가함에 따라 $\Delta$TSR=-1.35 K/Pr at.%의 비율로 단순 감소하였으나 R=Y인 경우에는 초기 소량의 감소 후 다시 약간 증가한다. 4.2 K에서 스핀재배열각(SRA)은 Y과 Pr 치환량의 증가에 따라 0$\leq$x$\leq$0.5의 범위에서 $\Delta$SRA=-0.073$^{\circ}$/T at.%와 $\Delta$SRA=-0.258$^{\circ}$/Pr at.% 비율로 감소한다. 4.2 K에서 결정자기이방성상수의 조사결과 R=Y인 경우 x=0.9 이상에서 R=Pr인 경우에는 x=0.8 이상에서 스핀재배열현상이 사라질 것으로 예측되었다.

  • PDF

Nd1+XBa2-XCu3O7-δ Bulk Superconductor by Zone-melt Process

  • Soh, Dea-Wha;Guo, Fan-Zhan
    • Transactions on Electrical and Electronic Materials
    • /
    • 제3권3호
    • /
    • pp.21-24
    • /
    • 2002
  • Two kinds of $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$, the sintering samples and zone melting samples, were heat-treated under pure Ar at 950$^{circ}C$. The substitution of Nd ion for Ba ion in the $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$ before and after the heat treatment was investigated by XRD. In order to confirm the effects of the heat treatment, the Tc and Jc of samples with/without the heat treatment under Ar were comparatively studied. $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$ samples were oxygenated under pure oxygen at $300^{circ}C$. From the XRD pattern it was found that the sample with x<0.4 was transferred from tetragonal phase to orthorhombic phase after the oxygenation, while the sample with x>0.4 did not show the phase transition even after a long time oxygenation. Therefore, the low oxygen partial pressure (Ar+1 % O$_2$) was used for the ambient atmosphere of the zone-melting samples, which could reduce the melting temperature and depress the substitution of Nd for Ba. After the improvement in the zone-melting process, the Jc value was increased to 2 x $10^4$A/$cm^2$ (0 T, 78 K). The particle orientation and the structure of zone-melted NdBaCuO were studied by the XRD and SEM analysis.