• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.261-264
• /
• 2000

Continuous ND filters are fabricated on the silver halide photoplates. These filters enable us to get intensity modulated laser beam. Two kinds of continuous ND filters are fabricated. Optical density of one filter is increased radically and that of the other is decreased. In order to get a filter having desirable optical density, a mask which has reversed optical density has to be made. made.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1589-1596
• /
• 2015

A novel control method of a three-phase PWM inverter with LC filter is proposed. The transfer function of LC filter is the same as that of 2nd order low pass filter(2nd LPF) which has a zero damping ratio. A simple method of implementing 2nd LPF with damping ratio is to add resistor to inductor or capacitor of LC filter. In an industrial application, it is not practical to adopt damping resistor because it results in losses being proportional to square of current flowing through resistor. Instead of using damping resistors, the proposed active damping control(ADC) utilizes all pass filter(APF) and considers inherent processing delay of digital controller. The overall transfer function of the proposed method is the same as a 2nd LPF and its damping ratio is also controllable via control variables. Detailed design and implementation of controller is also presented. Experiments are conducted with a 7.5kVA induction motor drive system controlled by PWM converter and inverter. Test waveforms are also presented to verify the proposed LC filter control algorithm.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2009.04a
• /
• pp.65-73
• /
• 2009

The terrestrial laser scanner measures the signal delay time of electronic circuit in EDM(Electronic Distance Measurement) Module for distance measurement. To measure signal delay time precisely, transmitting laser beam of terrestrial laser scanner is divided optically. Therefore, 10% of the laser beam power is entered into the electronic circuit and the others go out through lens. But, measure of delay time is severe in the laser scanner system that the laser beam power is changed dynamically by reflectance of a object, because characters like gain of electronic circuit involving APD(Avalanche Photo Diode) and so on are changed by incident laser beam. Therefore, we adapt ND(Neutral Density) filter that has grid pattern to the laser scanner system to keep constant the incident laser beam power. In this paper, we propose the simulation program for efficient design of ND filter pattern. Finally, to affirm simulation program, we conduct the experimental test of simulated ND filter that has linearly transmittance change, and we consider the experiment result.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.811-814
• /
• 1998

This paper proposes a constant time-delay filter with low sensitivity, which can be used for hard-disk drive. The sensitivity of 2nd order lowpass filter by two kinds of method, one is based on lossy integrators and the other is lossy and lossless integrators is analyzed and designed. SPICE simulation shows fesibility of a filter by the proposed approach.

• Journal of Power Electronics
• /
• v.18 no.5
• /
• pp.1513-1522
• /
• 2018

This paper proposes a new islanding detection method for inverter-based distributed generators by continuously injecting a negligible amount of 2nd order harmonic current. The proposed method adopts a proportional resonant (PR) controller for the output current control of the inverter, and a PR filter to extract the 2nd order harmonic voltage at the point of common coupling (PCC). The islanding state can be detected by measuring the magnitude ratio of the 2nd order harmonic voltage to the fundamental voltage at the PCC by injecting a 2nd order harmonic current with a 0.8% magnitude. The proposed method provides accurate and fast detection under grid voltage unbalance and load unbalance. The operation of the proposed method has been verified through simulations and experiments with a 5kW hardware set-up, considering the islanding test circuit suggested in UL1741.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.4
• /
• pp.293-299
• /
• 2004

An active RC 2nd order Butterworth filter suitable for a baseband channel-selection filter of a direct conversion receiver is presented. The linearity of the 2nd order Butterworth filter is analyzed. In order to improve the linearity of the filter, the operational amplifiers should have a high linear gain and low 3rd harmonic, and the filter should be designed to have large feedback factor. This second order Butterworth filter achieves-14dBV in-channel (400kHz, 500kHz) IIP3, +29dBV out-channel (10MHz, 20.2MHz) IIP3 and 15.6 $nV/\sqrt{Hz}$ input-referred noise and dissipates 10.8mW from a 2.7-V supply. The analysis and experimental results are in good agreement

• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.E2
• /
• pp.49-56
• /
• 2005

A long-path transmissometer is one of the optical instruments widely used to measure atmospheric light extinction coefficient without enclosing a light beam and perturbing aerosols. Over the past two decades, a number of measurements have been carried out using the long-path transmissometer manufactured by OPTEC, Inc. Calibration of the transmissometer should be performed when any component of the transmissometer system is interchanged or installation condition is changed. For a better calibration of the transmissometer, application of a modified calibration method for the existing neutral density (ND)-filter method was recommended for the computation of the atmospheric transmittance using model MODTRAN 4 in this study. It was revealed that the measured light extinction coefficient from the transmissometer which was calibrated using the existing ND-filter method could be overestimated due to the assumption of the atmospheric transmittance suggested by OPTEC, Inc. The uncertainty of the measured light extinction coefficient from the transmissometer calibrated based on the modified ND-filter method was calculated to be approximately $13Mm^{-1}$.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.52 no.4
• /
• pp.148-153
• /
• 2003

In this paper, the low voltage 3V Sigma-Delta Digital Analog Converter(DAC) is designed for using in the transmitter of ADSL analog front-end. We have developed the CMOS DAC according to ANSI T1.413-2(DMT) standard specifications of the chip. The designed 4th-order DAC is composed of three block which are 1-bit DAC, 1st-order Switched-Capacitor filter and analog active 2nd-order Resistor-Capacitor(RC) filter. The HSPICE simulation of the designed DAC showing 65db SNR, is connected with 1.1MHz continuous lowpass filter. And also, we have performed the circuits verification and layout verification(ERC, DRC, LVS) followed by fabrication using TSMC 2-poly 5-metal p-substrate CMOS $0.35{\mu}m$ processing parameter. Finally, the chip testing has been performed and presented in the results.

• Journal of Hydrospace Technology
• /
• v.1 no.1
• /
• pp.66-74
• /
• 1995

Unknown parameters can be determined by system identification techniques. Extended Kalman filter method was introduced as a real time estimator of hydrodynamic derivatives but it has the problem named the coefficient drift. In this study, 2nd order filter estimates hydrodynamic derivatives in Abkowitz model In order to reduce the coefficient drift, parallel processing is used. The measured state and ship trajectory are compared with the estimated values. Parallel processing of 2nd order filter gives very similar results to parallel processing of extended Kalman filter. Parallel processing cannot not remove the coefficient drift perfectly, but it reduces the estimation error.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.1C
• /
• pp.65-73
• /
• 2006

The purpose of this study is to design and analyze the pre-modulation filter with the variable -3dB cutoff frequency and linear phase response for bandlimiting the allocation of radio frequency bandwidth in PCM/FM transmission system. For the implementation of this required filter, the digital FIR filter, DAC and variable 2nd order LPF have been constructed with the filter block which designed and analyzed by each stage in order to satisfy the attenuation characteristic requirement of the analog 7th order bessel filter. The paper also concerned the linear phase properties for the filter block. Especially we have carried out the linear phase simulation with real parts for variable 2nd order LPF and compared this simulation results with the one of the fixed bandwidth 2nd order bessel filter for validating the linear phase requirement.