• The Korean Journal of Pain
• /
• v.14 no.2
• /
• pp.234-238
• /
• 2001

Percutaneous laser discectomy has potential advantages over conservative therapy and classical open surgery as a minimally invasive procedure, although clinical experiences are limited. We experienced a patient treated with herniated lumbar discs using Nd：YAG laser. A 55-year-old woman complained of severe back pain with sciatica on L4/5 and L5/S1 dermatome for several months. The MRI finding showed bulging discs at L4/5 and L5/S1. Epidural, transsacral and root block treatments were attempted without effect. Under fluoroscopic guidance, a 14 G biopsy needle was inserted into the L4/5 and L5/S1 disc spaces to the margin of the nucleus pulposus. Laser irradiation for vaporization of tissue was performed at 20 W/second to 1200 J. A laser fiber ($600{\mu}m$) was advanced 1 cm from the tip of the needle. At the end of the procedure, the patient began to feel relief of pain (VAS changed from 9 to 4) and was discharged the same day after staying 2 hours in the recovery room. Antibiotics were administered for prevention of discitis. She had no complaints of pain until the 1-month follow up visit. Percutaneous laser discetomy technique has the disadvantages of expensive equipment, high temperature and amount of vaporing disc tissue is empirical. However, this technique, as one of the therapeutic modalities for disc herniation, provides faster relief from acute attack than conservative management techniques in carefully selected patients with sciatica due to disc prolapse.

• Tribology and Lubricants
• /
• v.30 no.1
• /
• pp.59-63
• /
• 2014

Laser Surface Texturing(LST) is a surface engineering process used to improve tribological characteristics of materials by creating patterned microstructures on the mechanical contact surface. In LST technology, a pulsated laser beam is used to create arranged dimples on a surface by a material ablation process, which can improve such as load capacity, wear resistances, lubrication lifetime, and reduce friction coefficients. In the present study, the effect of multi-scale LST on lubricant regime was investigated. A pulsed Nd:YAG laser was applied on the bearing steel(AISI 52100) to create arranged dimples. To optimize the surface texturing effect on friction, multi-scale texture dimples with some specific formula arrays were fabricated by combining circles, ellipses and the laser ablation process. The tribological testing of multi-scale textured surface was performed by a flat-on-flat unidirectional tribometer under lubrication and the results compared with that of the non-textured surface. Through an increase in sliding speed, the beneficial effect of multi-scale LST performance was achieved. The multi-scale textured surface had lower friction coefficient performances than the non-textured surface due to the hydrodynamic lubrication effect.

• Journal of Welding and Joining
• /
• v.35 no.2
• /
• pp.58-62
• /
• 2017

A319 aluminum alloy containing 6.5% Si and 3.5% Cu as major alloying elements has been widely used in machinery parts because of its excellent castability and crack resistance. However it needs more wear resistance to extend its usage to the severe wear environments. It has been known that hyper-eutectic Al-Si alloy having more than 12.6% Si contains pro-eutectic Si particles, which give better wear resistance and lubrication characteristics than hypo-eutectic Al-Si alloy like A319 alloy. In this study, it was tried to clad hyper-eutectic Al-Si alloy on the surface of A319 alloy. In the experiments, Al-36%Si alloy powder was mixed with organic binder to make a fluidic paste. The paste was screen-printed on the A319 alloy surface, melted by pulsed Nd:YAG laser and alloyed with the A319 base alloy. As experimental parameters, the average laser power was changed to 111 W, 202 W and 280 W. With increasing the average laser power, the melting depth was changed to $142{\mu}m$, $205{\mu}m$ and $245{\mu}m$, and the dilution rate to 67.2 %, 72.4 % and 75.7 %, and the Si content in the cladding layer to 16.2 %, 14.6 % and 13.7 %, respectively. The cross-section of the cladding layer showed very fine eutectic microstructure even though it was hyper-eutectic Al-Si alloy. This seems to be due to the rapid solidification of the melted spot by single laser pulse. The average hardness for the three cladding layers was HV175, which was much higher than HV96 of A319 base alloy. From the block-on-roll wear tests, A319 alloy had a wear loss of 5.8 mg, but the three cladding layers had an average wear loss of 3.5 mg, which meant that an increase of 40 % in wear resistance was obtained by laser cladding.

• Journal of the Korean Chemical Society
• /
• v.24 no.5
• /
• pp.371-379
• /
• 1980

The spectral properties of the solvated electrons in tetrahydrofuran(THF)-water binary system have been investigated. In this study, the solvated electrons have been produced by applying nsec Q-switch Nd(YAG) laser photolysis technique. The experimental method photolysis were schematically described. The solvent and the temperature effects on the absorption spectrum of solvated electrons have also been studied. The observation of the spectrum with increasing THF content and temperatue showed a trend that the former shifted to longer wavelength and the other showed broadening effect. The half-life of solvated electrons were also increased with THF content. The absorption maxima of the mixtures were always observed in the middle of that of pure water and THF. The correlation between the volume and the absorption energy of solvated electrons were discussed from the results.

• Korean Journal of Remote Sensing
• /
• v.29 no.5
• /
• pp.581-588
• /
• 2013

We developed the three channel lidar system to measure stratospheric aerosols at the Gwangju Institute for Science and Technology (GIST), a suburban site in Republic of Korea. The system provides backscatter coefficient (${\beta}$) at 532 and 1064 nm as well as depolarization ratios (${\delta}$) at 532 nm ($2{\beta}+1{\delta}$) using the doubled Nd:YAG laser wavelength at 532 and 1064 nm. The lidar system is optimized to measure stratospheric aerosols such as volcanic ashes. This paper describes the details of the optical setup, data acquisition system, and analysis method. This study shows an example of measuring stratospheric aerosols emitted by the volcanic eruption which occurred in Mt. Nabro ($13.37^{\circ}$ N, $41.70^{\circ}$ E).

• Korean Journal of Crystallography
• /
• v.3 no.1
• /
• pp.37-43
• /
• 1992

KTiOP04 is a nonlinear optical crystal which is most widely used for frequency doubling of the radiation of Nd : YAG laser. In the experiment, sin ale crystals of KTiOP04 were grown by TSSG technique using 3K2W04·P2O5 flux. Low temperature gradient furnace suitable for KTP single crystal growth was used. Seed crystal was placed at the surface of the solution for the purpose of better observation of the growing crystals and the possibility of diameter control. Solution included 66.7mol% KTiOP04 for all experiments and its saturation temperature was 1020℃. The conditions of single crystal growth were as follows: cooling rate 0.2℃/h, crystal rotation rate 50rpm, c -axis seed. Using these conditions, single crystals up to 23 ×25×25mm3 have been groan from about 100cc solution. We have also observed a change in the crystal growth habit which resulted in the formation of large (201) faces and small (100) faces. And some crystals have (101) faces.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.9
• /
• pp.799-804
• /
• 2007

The behavior of spray emanating from an injector to be employed in a liquid-propellant thrust chamber is investigated by optical measurement techniques. The injector has eight holes, each of which has 30 cant angle from the center-axis with the diameter of 0.406 mm. In order to examine an atomization process according to the spray-generation conditions and the evolution along spray downstream, variational features in the velocity and size of droplets obtained through Dual-mode Phase Doppler An 799emometry (DPDA) are delineated and discussed together with instantaneous plane images captured by using Nd:Yag laser sheet beam. A categorization of spray-flow regime representing the atomization and turbulent nature is made through evaluating the non-dimensional parameters, i.e., Reynolds number and Weber number based upon the theoretical injection velocity. These qualitative and quantitative data of spray breakup will be a firm basis for the design of brand-new thruster

• Korean Journal of Optics and Photonics
• /
• v.16 no.2
• /
• pp.121-127
• /
• 2005

This paper presents the thermal characteristics of a Bragg grating recorded in photopolymer. We record hologram gratings using a 532 nm Nd : YAG laser in DuPont HRF 150-38 photopolymer films and analyze the diffraction efficiency versus thermal exposure conditions. For the case of recording after heating, the diffraction efficiency of the hologram is more than $70\%$ at $100^{\circ}C$ but is decreased exponentially at temperatures over $100^{\circ}C$. It is observed in the recording before heating that the diffraction efficiency of the hologram fixed by a UV light is increased to approximately $10\%$ at $100^{\circ}C$, but the holograms are erased at temperatures over $120^{\circ}C$.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2009.06a
• /
• pp.467-470
• /
• 2009

A novel 8 V DC power source with an external series-parallel connection of 50 Dye-Sensitized Solar Cells(DSSCs) has been proposed. One DSC has the optimized length to width ratio of $5.2{\times}2.6$ cm and an active area 8 $cm^2$($4.62{\times}1.73$ cm) which attained a conversion efficiency of 4.2%. From the electrochemical impedance spectroscopic analysis, it was found that the resistance elements related to the Pt electrode and electrolyte interface behave like that of diode and the series resistance corresponds to the sum of the other resistance elements. In addition, the TEMoo mode pulsed Nd:YAG laser beam is used to improve the incident photon to current efficiency(IPCE) of DSSC. From this result, this novel 8V-0.38A DC power source shows stable performance with an energy conversion efficiency of about 4.5% under 1 sun illumination(AM 1.5, Pin of 100 $mW/cm^2$).

• Journal of Oral Medicine and Pain
• /
• v.23 no.1
• /
• pp.11-20
• /
• 1998

저자는 치과용 레이저를 이용한 상아질지각과민증 치료효과를 임상적으로 평가하고자 상아질지각과민증환자 24명을 대상으로 각 환자마다 상아질 지각과민 치아 중 레이저로 치료 할 치아1개(실험군)와 치료하지 않을 치아 1개(대조군)를 선정하여, 치과용 air-syringe에 의한 냉자극과 치과용 탐침자에 의한 기계적 자극을 가한 후 Visual Analogue Scale(VAS)을 통해 지각과민증 정도를 평가하였으며, 이후 실험군 치아의 치경부 마모면에 광섬유 레이저에너지 전달방식의 펄스형 Nd:YAG 레이저의 일종인 Sunlase Master(Sunrise Technologies Inc., U.S.A., 파장 1064nm, 펄스지속시간 120(sec, 광섬유직경 320(m)를 사용하여, 0.3-1.0W, 10Hz 조건으로 환자의 반응에 따라 1회2분을 초과하지 않는 범위 내에서 비접촉식과 접촉식을 병행하여 3회에 걸쳐(초진 당일, 1일후, 3일후) 레이저를 조사한 후 처음조사 직후, 그리고 초진 1일후, 3일후, 7일후, 14일후 VAS를 채득하여 조사전과 비교, 분석, 평가하였던 바, 상아질 지각과민증이 각각 약 50%, 약36%, 약45%, 약 53% 감소하였으나 (p(0.05) 경시적으로는 유의한 차이를 보이지 않았다. 그리고 24명중 9명에 대해서는 초진 30일 후 까지 레이저조사치료효과를 평가하였던 바, 상아질지각과민증이 처음조사 직후, 감소하였으며 (p(0.05)역시 경시적으로는 유의한 차이를 보이지 않았다. 초진 30일 후 상아질지각과민증이 초진 14일 후에 비해 약간 증가되는 경향을 보여, 레이저조사 치료효과가 약화되는 경향인지 여부에 대해 향후 추가적인 연구가 필요할 것으로 사료된다.안되었다.기란 현실적으로 불가능하므로, 본 연구에서는 이러한 제약점을 극복할 수 있는 근사적인 지체시간을 계산하는 방법을 제시한 점에서 의미를 갖을 수 있다.수들은 직업의 선택이나 소득을 예측하기 위한 요소들로 포함될 수 없었다. 따라서 후속연구에서는 이를 보완해야 할 것이며, 최근 들어 우리 나라에서도 재택근무에 대한 관심이 대두되고 있으나 아직 개념정의나 그 중요성과 가치, 그리고 실태 파악과 같은 연구가 활발히 이루어지지 못하고 있으므로 이에 대한 심층적인 연구가 행해져야 할 것이다.d similar flower proceeding dates in all branches. but "Daepung" showed similar flower proceeding dates in all branches.est in HB. Mean period of wetting duration was in the order of DS＞HB＞MB, while the dew point depression was greatest in DS.ANCOVA, Pearson correlation을 이용하여 분석하였으며, 그 결과는 다음과 같다. 캠프 프로그램은 소아 당뇨병 환자의 자기 효능을 증진시키고 환자 역할 행위 이행을 높여주는데 효과적 이었다. 소아 당뇨병 환자의 자기 효능은 환자 역할 행위 이행과 순 상관 관계가 있어, 자기 효능이 증진될수록 환자 역할 행위 이행 정도가 높아졌다. 무조건 사주지 않는다(8.0%), 무조건 사준다(3.1%)로 식품광고에 나오는 식품 요구시 부모의 70.3%가 거절하는 것으로 나타났다. 거절 이유는 건강에 나쁘다는 것이 가장 큰 이유였으며 강남과 강북 어린이간에 유의적인 차이가 있었다(p＜0.001).