• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제11권1호
• /
• pp.101-116
• /
• 1989

Proplast and Porous Polyethylene which have porous structures as low-modulus polymers have been recently used in maxillofacial plastic and reconstructive surgery. The purpose of this study was to compare the response of adajacent tissue, new bone formation and stability after augmentation by differen methods of subperiosteal graft using proplast and purous polythylene in rabbit mandible. The augmentation procedure was carried out by dividing into two groups, A and B. A group consisted of subperiosteal graft on the cortex, and the other B group was made up only graft following artificial decortication in the mandibular body of rabbit. The experimental animals were sacrificed on the 1st, 2nd, 4th and 8th week after grafting for macroscopic and light microscopic examination. The samples extracted at the 6th postgrafting week were also used for biometric testing and scanning electron microscopic examination. The results obtained from this study were as follows : 1. Macroscopically, infection of graft site, deformation and migration of graft material were not observed in all experimental groups. 2. B group showed more rapid and increased bone formation and the greater stability than A group, and tissue response was similar to each other. 3. In the tissue response, macrophages and cellular infiltrations were observed in Proplast group, but few in PHDPE group. 4. In bone formation of A group, Proplast group showed no bone formation until the 8th week, but PHDPE group showed small quantity of osteoid tissue from the 2nd week and appositional bone growth with new bone formation at the 8th week. 5. In bone formation of B group, both Proplast and PHDPE group showed bone formation, but PHDPE group showed more rapid and larger bone formation. 6. In pattern of bone formation, Proplast group mainly showed appositional bone growth pattern connected with graft site. On the other hand, PHDPE group showed mixed pattern of new bone formation in the pore connective tissue with appositional bone growth from graff site. 7. The maximum mean values of shear stress were serially $111.3gf/mm^{2}$ in PHDPE of B group, $84.8gf/mm^{2}$ in PHDPE of A group, $32.9gf/mm^{2}$ in Proplast B group, and $15.7gf/mm^{2}$ in Proplast of A group. From above results, It was suggested that the capacity of bone formation and stability between bone and graft material were dependent on the pore size and structure of graft material itself, the state of graft site and tissue response.

• 대한치과교정학회지
• /
• 제41권2호
• /
• pp.98-111
• /
• 2011

본 연구는 정모두부방사선사진 촬영 시 두부의 수직회전에 따라 달라지는 계측점의 위치변화를 방사선원리를 이용하여 계산으로 보정한 후 이러한 보정 방법이 타당한지 알아보고자 시행되었다. 성인 30명을 대상으로 동일한 두부자세에서 정모 및 측모두부방사선사진을 서로 직각이 되게끔 촬영한 다음 두부를 $5^{\circ}$ 하방으로 수직회전 시 정모두부방사선사진상 여러 계측점의 변화를 방사선의 기하학적 원리률 이용하여 수직 및 수평방향으로 구분하여 산출한 후, 이를 실제로 두부를 $5^{\circ}$ 회전시킨 상태에서 촬영한 정모방사선사진에서의 계측점 변화와 비교 분석하였다. 실제로 두부를 $5^{\circ}$ 회전시킨 상태에서 촬영한 정모방사선사진에서의 계측점 변화를 수평방향과 수직방향으로 구분하여 살펴본 결과 수평적으로는 작은 변화를 보인 반면 수직적으로는 전반적으로 큰 변화를 나타내었다. 두부 회전 시 수직변화를 계측점별로 살펴본 결과 ear rod축에서 전방으로 멀리 떨어진 계측점일수록 그 변화가 큰 것으로 나타났다. 두부의 $5^{\circ}$ 수직회전 시 계측점의 변화를 계산을 통해 산출한 후, 산출된 수치와 실제 수치를 비교한 결과 수직방향의 경우 0.4 mm 미만, 수평방향의 경우 0.2 mm 미만의 작은 수치를 나타내었다. 아울러 두부의 수직회전에 영향을 적게 받는 계측점일수록 그 차이가 작은 경향을 보였다. 본 연구 결과는 정모 및 측모두부방사선사진을 서로 직각이 되게끔 촬영할 경우, 두부의 수직회전으로 인한 정모두부방사선사진상의 계측점 변화를 회전 전 위치로 산출 보정하는 것이 가능함을 보여주었다.

• 치과방사선
• /
• 제28권1호
• /
• pp.111-126
• /
• 1998

In this study, radiographic evaluation was made using panoramic radiography and cross-sectional tomography of SCANORA/sup (R)/ in male and female adults in their 20's on the relationship between the maxillary sinus floor and the apex of the maxillary molar, to test the accuracy and effectiveness of the cross-sectional tomography, and to use this information in the assessment of preop. and postop. root canal treatment, apical surgery, extraction and implantology. Forty-one adults with an average age of 24.4 years were studied using panoramic radiography and cross-sectional tomography. In panoramic view and cross-sectional view, the position of the apices of maxillary molars were classified as separated, contacted, or protruded type; the general shape of the maxillary sinus floor was evaluated horizontally and vertically from cross-sectional tomography. The accuracy of each radiography was tested using maxilla from 5 fresh cadavers from the Anatomy Lab at Yonsei University Dental College, and panoramic view and cross-sectional tomography were taken in the same condition as with the patients. The results were as follows: 1. Panoramic view and cross-sectional view were taken in the maxilla specimen, and the actual distance between the maxillary sinus floor and the tooth apices were measured in the specimen; the median values of the distance from the tooth apices to the maxillary sinus floor in the panoramic view, cross-sectional view and in the actual maxilla specimen were 2.83 mm, 4.51mm, and 4.l5mm, respectively. In the cross-sectional view, the measured distance was close to the actual distance but in the panoramic view, the measured distance was far from the actual distance. 2. When the results of the panoramic view and cross-sectional view were compared, 40.5％ of the results agreed with each other in the two radiographic methods and buccal roots of the 2nd molar were the closest to the maxillary sinus floor in the cross-sectional tomography. 3. In cross-sectional view, when the vertical relationship of the maxillary sinus floor and maxillary roots was assessed, in 1st molars, type II (the sinus floor that extends down to the buccolingual furcation area) was predominant, while in 2nd molars, type I (the sinus floor located above the level connecting the buccal and lingual apices) was predominant. In the horizontal relationship, in 1st molars, type II (the lowest floor of the maxillary sinus located in between the buccal and lingual roots) was predominant; in 2nd molars, type I (the lowest floor of the maxillary sinus located on the buccal side of the buccal roots) and type II appeared in similar frequency. In conclusion, the SCANORA/sup (R)/ cross-sectional tomography was more effective than the frequently used panoramic view, in that the relationship of the maxillary molars and maxillary sinus floor can be evaluated more accurately and the buccolingual cross-sectional view can also be observed. And maxillary sinus floor that was close to maxillary 2nd molar had tendency to be located on buccal side than that close to 1st molar. Therefore, cross-sectional tomography is an effective and accurate method to evaluate the position of the teeth in relation to the sinus floor preoperative and can be easily used to diagnose localized periapical lesions. Also, the image quality obtained was quite satisfactory.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2006년도 학술발표회 논문집
• /
• pp.386-390
• /
• 2006

금번 연구에서는 낙동강 유역내 주요하천을 대상으로 자연도 평가와 수질을 분석하였다. 하천 자연도의 종합평가 결과는 $1.428{\sim}4.107$의 1등급과 4등급으로 평가 되었으며, 부문별 평가 결과는 하천형태의 평가지수가 $2.111{\sim}4.048$으로 2등급에서 4등급으로, 하천환경의 평가지수는 $1.774{\sim}3.643$의 1등급에서 4등급으로 평가되었다. 수질 평가 결과는 수소이온농도는 $7.102{\sim}8.497mg/{\ell}$이었으며, 생물화학적 산소요구량은 $0.748{\sim}5.271mg/{\ell}$, 용존산소량 $3.668{\sim}19,960mg/{\ell}$, 부유물질은 $5.077{\sim}12.335mg/{\ell}$이었다. 하천 자연도 평가 지표의 독립성과 유사성을 판단하기 위하여 하천 자연도 평가와 수질 상관분석을 실시한 결과, 상관계수가 $-0.1503{\sim}-0.5886$로 낮은 상관성을 갖고 있으며, 서로 독립적인 지표인 것으로 분석되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.58-58
• /
• 1999

The diamond films which can be applied to SOD (silicon-on-diamond) structure were deposited on Si(100) substrate using CO/H2 CH4/H2 source gases by microwave plasma chemical vapor deposition(MPCVD), and SOD structure have been fabricated by poly-silicon film deposited on the diamond/Si(100) structure y low pressure chemical vapor deposition(LPCVD). The phase of the diamond film, surface morpholog, and diamond/Si(100) interface were confirmed by X-ray diffraction(XRD), scanning electron microscopy(SEM), atomic force microscopy(AFM), and Raman spectroscopy. The dielectric constant, leakage current and resistivity as a function of temperature in films are investigated by C-V and I-V characteristics and four-point probe method. The high quality diamond films without amorphous carbon and non-diamond elements were formed on a Si(100), which could be obtained by CO/H2 and CH4/H2 concentration ratio of 15.3% and 1.5%, respectively. The (111) plane of diamond films was preferentially grown on the Si(100) substrate. The grain size of the films deposited by CO/H2 are gradually increased from 26nm to 36 nm as deposition times increased. The well developed cubo-octahedron 100 structure nd triangle shape 111 are mixed together and make smooth and even film surface. The surface roughness of the diamond films deposited by under the condition of CO/H2 and CH4/H2 concentration ratio of 15.3% and 1.5% were 1.86nm and 3.7 nm, respectively, and the diamond/Si(100) interface was uniform resistivity of the films deposited by CO/H2 concentration ratio of 15.3% are obtained 5.3, 1$\times$10-9 A/cm, 1 MV/cm2, and 7.2$\times$106 $\Omega$cm, respectively. In the case of the films deposited by CH4/H2 resistivity are 5.8, 1$\times$10-9 A/cm, 1 MV/cm, and 8.5$\times$106 $\Omega$cm, respectively. In this study, it is known that the diamond films deposited by using CO/H2 gas mixture as a carbon source are better thane these of CH4/H2 one.

• 한국응용곤충학회지
• /
• 제51권4호
• /
• pp.461-467
• /
• 2012

참딱부리긴노린재의 생물학적 특성을 조사하기 위하여, 온도 $20{\pm}1$, $25{\pm}1$, $30{\pm}1$, $35{\pm}1$, $37.5{\pm}1$, $40{\pm}1^{\circ}C$, 습도 $80{\pm}10%$, 광주기 16:8(L:D)에서 발육실험을 실시하였다. 그 결과 알부터 성충우화까지의 발육영점온도는 $14.8^{\circ}C$, 유효적산온도는 399.1일도였다. $35^{\circ}C$에서 조사한 결과를 정리하면 다음과 같다. 알 기간은 5.6일, 부화율은 81.1%, 약충 기간은 14.3일(1령 3.2, 2령 2.2, 3령 2.7, 4령 2.7, 5령 3.6일)이었다. 암컷 성충의 수명은 33.8일, 산란기간은 29.2일이었다. 총 산란수는 111.2개, 하루 최대산란수는 14.8개(7일차)였다. 알과 약충은 $37.5^{\circ}C$까지만 발육하고 $40^{\circ}C$에서는 발육하지 못했으며, $40^{\circ}C$에서 총 산란수는 22.1개였다. 참딱부리긴노린재 1령, 3령, 5령, 성충의 담배가루이 번데기 하루 포식량은 각각 1.9, 7,3, 18.7, 29.5마리였다.

• 한국재료학회지
• /
• 제22권6호
• /
• pp.303-308
• /
• 2012

This study evaluated the enhancement of microstructural and mechanical properties of a cross rolled Ni-10Cr alloy, comparing with conventionally rolled material. Cold rolling was carried out to 90% thickness reduction and the specimens were subsequently annealed at $700^{\circ}C$ for 30 min to obtain a fully recrystallized microstructure. Cross roll rolling was carried out at a tilted roll mill condition of $5^{\circ}$ from the transverse direction in the RD-TD plane. In order to observe the deformed microstructures of the cold rolled materials, transmission electron microscopy was employed. For annealed materials after rolling, in order to investigate the grain boundary characteristic distributions, an electron back-scattering diffraction technique was applied. Application of cold rolling to the Ni-10Cr alloy contributed to notable grain refinement, and consequently the average grain size was refined from 135 ${\mu}m$ in the initial material to 9.4 and 4.2 ${\mu}m$ in conventionally rolled and cross rolled materials, respectively, thus showing more significantly refined grains in the cross rolled material. This refined grain size led to enhanced mechanical properties such as yield and tensile strengths, with slightly higher values in the cross rolled material. Furthermore, the <111>//ND texture in the CRR material was better developed compared to that of the CR material, which contributed to enhanced mechanical properties and formability.

• 소성∙가공
• /
• 제23권2호
• /
• pp.82-87
• /
• 2014

The plastic strain ratio is one of the factors that affect the deep drawability of Al alloy sheet. The deep drawability of Al alloy sheet is limited because of its low plastic strain ratio. Therefore an increase in the plastic strain ratio to improve the deep drawability of Al alloy sheet is needed. The current study investigated the increase of the plastic strain ratio and the change in texture of AA5083 Al alloy sheet after a 2 step asymmetric rolling with heat treatments. The average plastic strain ratio of initial AA5083 Al alloy sheets was 0.83. After the first asymmetric rolling step of 88% deformation and subsequent heat treatment at $320^{\circ}C$ for 10 minutes the value was still 0.83. After the second asymmetric rolling of 14% reduction and subsequent heat treatment at $330^{\circ}C$ for 10 minutes the plastic strain ratio rose to 1.01. The average plastic strain ratio after the 2 step asymmetric rolling and heat treatment is 1.2 times higher than that of initial AA5083 Al alloy sheet. This result is related to the development of ND/<111> texture component after the second asymmetric rolling and heat treatment.

• 미생물학회지
• /
• 제30권3호
• /
• pp.225-231
• /
• 1992

생물체내의 ascorbic acid :dehydroascorbic acid system 을 조절하는데 관여하는 것으로 알려진 ascorbate 산화효소의 활성을 단세포 녹조류인 Chlamydomonas reinhardtii 에서 확인함으로써 이 효소의 존재와 특성을 고찰하였다. 조효소는 native gel 전기 영동에 의한 활성 염색과 분광광도계에 의한 ascorbic acid .의 흡광도 감소 측정에서 뚜렷한 활성을 나타내었다. 황산암모늄 침전, hydroxyapatite 흡착 크로마토그래피, 그리고 Sephadex G-150 gel 여과 크로마토그래피 분리한 결과 26.1 units/mg /의 specific activity 를 나타내었다. 분리된 ascorbate 산화효소는 $55^{\circ}C$, pH 4.6 에서 가장 활성도가 높았다. Native gel 전기 영동에서 88,000 dalton 갸량의 분자량을 가지고 있었고 소단위체의 분자량을 55,000 이었다. 또한 Western bloting technique 을 이용하여 C. reinhardtii 의 ascorbate oxidase를 확인하였다.

• 대한전자공학회논문지SD
• /
• 제45권6호
• /
• pp.111-118
• /
• 2008

액정 구동 IC에서 발생하는 기생 p-n-p-n 회로의 래치업 문제를 개선하기 위해 power-up 순서상에 순차 스위치를 삽입하는 방법을 제안하였다. 제안된 순차 스위치는 2차-승압회로와 3차-승압회로 내에 삽입되며, power-up 순서상에서 해당 승압회로가 동작하기 전에 기생 p-n-p-n 회로의 분리된 에미터-베이스 단자를 순차적으로 연결하게 된다. 제안된 구조의 성능을 검증하기 위해 0.13-um CMOS 공정을 이용하여 테스트 IC를 설계 제작하였다 측정 결과, 기존의 경우 $50^{\circ}C$에서 액정 구동 전압이 VSS로 수렴하면서 과전류를 동반하며 래치업 모드로 진입하였으나, 제안 회로를 삽입한 경우는 고온($100^{\circ}C$)에서도 정상 전류 0.9mA와 정상 액정 구동 전압을 나타내어 래치업이 방지되고 있음을 확인하였다.