• 한국전기전자재료학회논문지
• /
• 제29권3호
• /
• pp.159-163
• /
• 2016

In this paper, in order to develop optimum composition ceramics with excellent piezoelectric properties, $(Na_{0.525}K_{0.443}Li_{0.037})(Nb_{0.823}Sb_{0.08}Ta_{0.037})O_3+0.3wt%Bi_2O_3+0.4wt%Fe_2O_3$ lead-free piezoelectric ceramics were synthesized by conventional soild-state method. The calcination temperature of columbite precursors were fabricated at temperature range from $950^{\circ}C$ to $1,150^{\circ}C$ and sintering aids with low melting point were added to densify these ceramics. Effect of calcination temperature on dielectric and piezoelectric properties of ceramics were investigated. the ceramics with B-site columbite precursors at temperature of $1,100^{\circ}C$ obtained the optimal values of $d_{33}=272$ [pC/N], $k_p=0.51$, $Q_m=102$, ${\varepsilon}_r=978$.

• Structural Engineering and Mechanics
• /
• 제6권2호
• /
• pp.143-159
• /
• 1998

The objective of this present work is to estimate the failure loads, associated maximum transverse displacements, locations and the modes of failure, including the onset of delamination, of thin, square symmetric laminates under the action in-plane positive (+ve) shear load. Two progressive failure analyses, one using the Hashin criterion and the other using a Tensor polynomial criterion, are used in conjunction with finite element method. First order shear deformation theory along with geometric non-linearity in the von Karman sense have been employed. Variation of failure loads and failure characteristics with five type of lay-ups and three types of boundary conditions has been investigated in detail. It is observed that the maximum difference between failure loads predieted by various criteria depends strongly on the laminate lay-up and the flexural boundary restraint. Laminates with clamped edges are found to be more susceptible to failure due to transverse shear (ensuing from the out of plane bending) and delamination, while those with simply supported edges undergo total collapse at a load slightly higher than the fiber failure load. The investigation on negative (-ve) in-plane shear load is in progress and will be communicated as part-II of the present work.

• Structural Engineering and Mechanics
• /
• 제3권2호
• /
• pp.121-133
• /
• 1995

It is well known that two-dimensional simplified third-order theories satisfy the layer interface continuity of transverse shear strains, thus these theories violate the continuity of transverse shear stresses when two consecutive layers differ either in fibre orientation or material. The third-order theories considered herein involve four/or five dependent unknowns in the displacement field and satisfy the condition of vanishing of transverse shear stresses at the bounding planes of the plate. The objective of this investigation is to examine (i) the flexural response prediction accuracy of these third-order theories compared to exact elasticity solution (ii) the effect of layer interface continuity conditions on the flexural response. To investigate the effect of layer interface continuity conditions, three-dimensional elasticity solutions are developed by enforcing the continuity of different combinations of transverse stresses and/or strains at the layer interfaces. Three dimensional twenty node solid finite element (having three translational displacements as degrees of freedom) without the imposition of any of the conditions on the transverse stresses and strains is also employed for the flexural analysis of the laminated plates for the purposes of comparison with the above theories. These shear deformation theories and elasticity approaches in terms of accuracy, adequacy and applicability are examined through extensive numerical examples.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1996년도 추계학술대회
• /
• pp.151-154
• /
• 1996

A medical record and radiographic image transmission system has been developed using high speed communication network. The databases are designed to store and transmit the data acquired from the scanner. To maximally utilize the communication bandwidth, the medical records and radiographic images are compressed using the G3 facsimile and JPEG coding standard method respectively. TCP/IP, OOP and window based system software enables the modular design, future expandability, open system interconnectivity, and graphical user interface. In addition, the fast and easy data base access capability and diverse image manipulation functions are also implemented.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.182-189
• /
• 2005

In order to investigate the effect of premixed gasoline, diesel fuel, and n-heptane charges on the combustion and exhaust emission characteristics in a direct injection (DI) diesel engine, the experimental studies are performed. The premixed fuels are injected into the premixing chamber that installed upstream of the intake port in order to minimize the inhomogeneity effect of premixed charge. The injection nozzle for directly injected fuel is equipped in the center of the combustion chamber. The air temperature control system is equipped in the intake manifold to examine the effect of air temperature. The experimental results of this study show premixing fuel is effective method to reduce the NOx and soot emissions of diesel engine. NOx emissions are linearly decreased with increasing premixed ratio for the three kinds of premixed fuels. The heating of intake air $(80^{\circ}C)$ reduced the deterioration of BSFC in high premixed ratio, because it promotes evaporation of premixed diesel droplet in the premixing chamber.

• 동력기계공학회지
• /
• 제18권6호
• /
• pp.34-39
• /
• 2014

In this study, the structural analysis and the modal analysis are conducted to investigate the stress level, the deformation characteristics and the natural modes of the casing of a planetary gear reducer for a 800kW grade pulverizer mill. The casing is subjected to the load, 2800 kN, from the lump coals in the pulverizing process. Because of the symmetry, the half portion of the reducer casing is modeled for the stress analysis. But the full model is used to find out the eigenvalues and natural modes for the modal analysis. The contact conditions are applied between the thrust pad bearing and the adjacent contacting parts. The results shows that the casing structure has the sufficient strength and stiffness to support the load under consideration. ANSYS version 15 is employed to perform the numerical study.

• 한국산업보건학회지
• /
• 제22권2호
• /
• pp.91-99
• /
• 2012

Airborne chlorpyrifos concentrations in formulation workplaces have not been determined in Korea. The aim of the study was to evaluate chlorpyrifos concentrations of air in a formulation workplace and recognize the RBC cholinesterase activities for the formulation workers. 30 air samples (personal or area sampling) were collected and bood samples from 10 workers were collected for RBC chlorinesterase (RBC AChE) activity in a factory on May 2008. Air samples were collected by the National Institute for Occupational Safety and Health (NIOSH) method and were analyzed by GC-MS. Airborne chlorpyrifos concentrations ranged from 0.003 to $12.90mg/m^3$ and geometric mean (GM) was $0.15\;mg/m^3.$ Compared to Korean Occupational Exposure Limit (KOEL) of 0.1 (2011) or $0.2\;mg/m^3$ (2008), at 95% confidence, airborne concentrations exceeded the KOEL 69.7% or 56.1% of the time or less, indicating that this concentration level was unacceptable according to exposure assessment using a LogNorm2$^{(R)}$. Since the workers were continually at work on the organophosphate or carbamate pesticides formulation, individual baseline for RBC AChE activity was not determined. As the results of comparison with reference average value of RBC AChE activity, it was found that a worker was below 70% RBC AChE activity and five workers were abnormal.

• Advances in Energy Research
• /
• 제3권2호
• /
• pp.81-95
• /
• 2015

Microgrid, which can be considered as an integration of various dispersed resources (DRs), is characterized by number of DRs interfaced through the power electronics converters. The microgrid comprising these DRs is often operated in an islanded mode. To minimize the cost, reduce complexity and increase reliability, it is preferred to avoid any communication channel between them. Consequently, the droop control method is traditionally adopted to distribute active and reactive power among the DRs operating in parallel. However, the accuracy of distribution of active and reactive power among the DRs controlled by the conventional droop control approach is highly dependent on the value of line impedance, R/X i.e., resistance to reactance ratio of the line, voltage setting of inverters etc. The limitations of the conventional droop control approach are demonstrated and a modified droop control approach to reduce the effect of impedance mis-match and improve the time response is proposed. The error in reactive power sharing is minimized by inserting virtual impedance in line with the inverters to remove the mis-match in impedance. The improved time response is achieved by modifying the real-power frequency droop using arctan function. Simulations results are presented to validate the effectiveness of the control approach.

• 약학회지
• /
• 제42권1호
• /
• pp.12-24
• /
• 1998

For the development of new cephalosporin antibiotics with aminothiazolcarboxymethylethoxyimino moiety on the C-7 position and tetrazolymethyl moiety on the C-3 position of cephe m ring, 7${\beta}$-[(Z)-2-(2-aminothiazol-4-yl)-2-(1-carboxy-1-methylethoxyimino)acetamido]-3-[5-(substituted)tetrazol-2-yl]methyl-3-cephem-4-carboxylic acids(28-35) were synthesized. These compounds were tested for antimicrobial activity in vitro against Gram(+) and Gram(-) bacteria. They showed remarkable antibacterial activity against Escherichia coli AB 1157, Escherichia coli AB 0111, Escherichia coli BE 1186, Micrococcus luteus ATCC 9341, Salmonella typhimurium TV 119, Salmonella typhimurium SL 1102, Staphylococcus aureus IFO 12732, Staphylococcus aureus R-209, but these compounds were not active against Pseudomonas aeruginosa N-10.

• 반도체디스플레이기술학회지
• /
• 제18권2호
• /
• pp.48-52
• /
• 2019

Virtual metrology, which is one of APC techniques, is a method to predict characteristics of manufactured films using machine learning with saving time and resources. As the photoresist is no longer a mask material for use in high aspect ratios as the CD is reduced, hard mask is introduced to solve such problems. Among many types of hard mask materials, amorphous carbon layer(ACL) is widely investigated due to its advantages of high etch selectivity than conventional photoresist, high optical transmittance, easy deposition process, and removability by oxygen plasma. In this study, VM using different machine learning algorithms is applied to predict the thickness of ACL and trained models are evaluated which model shows best prediction performance. ACL specimens are deposited by plasma enhanced chemical vapor deposition(PECVD) with four different process parameters(Pressure, RF power, $C_3H_6$ gas flow, $N_2$ gas flow). Gradient boosting regression(GBR) algorithm, random forest regression(RFR) algorithm, and neural network(NN) are selected for modeling. The model using gradient boosting algorithm shows most proper performance with higher R-squared value. A model for predicting the thickness of the ACL film within the abovementioned conditions has been successfully constructed.