• Corrosion Science and Technology
• /
• v.16 no.3
• /
• pp.100-108
• /
• 2017

In this investigation corrosion behavior of newly developed high-pressure die cast Al-Ni (N15) and Al-Ni-Ca (NX1503) alloys was studied in 3.5% NaCl solution. The electrochemical corrosion behavior was evaluated using open circuit potential (OCP) measurement, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. Potentiodynamic polarization results validated that NX1503 alloy exhibited lower corrosion current density ($i_{corr}$) value ($5.969{\mu}A/cm^2$) compared to N15 ($7.387{\mu}A/cm^2$). EIS-Bode plots revealed a higher impedance (${\mid}Z{\mid}$) value and maximum phase angle value for NX1503 than N15 alloy. Equivalent circuit curve fitting analysis revealed that surface layer ($R_1$) and charge transfer resistance ($R_{ct}$) values of NX1503 alloy was higher compared to N15 alloy. Immersion corrosion studies were also conducted for alloys using fishing line specimen arrangement to simultaneously measure corrosion rates from weight loss ($P_W$) and hydrogen volume ($P_H$) after 72 hours and NX1503 alloy had lower corrosion rate compared to N15 alloy. The addition of Ca to N15 alloy significantly reduced the Al3Ni intermetallic phase and further grain refinement may be attributed for reduction in the corrosion rate.

• Journal of computational fluids engineering
• /
• v.22 no.1
• /
• pp.59-66
• /
• 2017

The guideline of selecting the number of snapshot dataset, $N_s$ in proper orthogonal decomposition(POD) was presented via the analysis of Eigen values based on the singular value decomposition(SVD). In POD, snapshot datasets from the solutions of Euler or Navier-Stokes equations are utilized to SVD and a reduced order model(ROM) is constructed as the combination of Eigen vectors. The ROM is subsequently applied to reconstruct the flowfield data with new set of flow conditions, thereby enhancing the computational efficiency. The overall computational efficiency and accuracy of POD is dependent on the number of snapshot dataset; however, there is no reliable guideline of determining $N_s$. In order to resolve this problem, the order of maximum to minimum Eigen value ratio, O(R) from SVD was analyzed and presented for the decision of $N_s$; in case of steady flow, $N_s$ should be determined to make O(R) be $10^9$. For unsteady flow, $N_s$ should be increased to make O(R) be $10^{11\sim12}$. This strategy of selecting the snapshot dataset was applied to two dimensional NACA0012 airfoil and vortex flow problems including steady and unsteady cases and the numerical accuracies according to $N_s$ and O(R) were discussed.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.305-314
• /
• 1998

This study has been performed to investigate into some effects of various amounts of $CO_2$ and CO gas added to the $50%NH_3-N_2$ based gas atmosphere on microstructure, hardness, chemical analysis and residual stress in the compound and diffusion layer of AISI H13 treated by gaseous nitrocarburising process. The compound layer formed in the surface is composed of mainly ${\varepsilon}-Fe_3$(N,C) and small amount of ${\gamma}^{\prime}-Fe_4N$ and cementite. The maximum hardness value obtainable from H13 steel is shown to be 1200 Hv and the effecvtive hardening depth increases with increasing CO content from 1% to 4%. In the case of CO content over 4%, however, it decreases with increasing CO content. The composition profiles of nitrogen and carbon are found to be within the ${\varepsilon}$-phase field located above the ${\varepsilon}+{\gamma}^{\prime}$ phase field in the Fe-N-C diagram. It is shown that the maximum value of compressive residual stress of H13 steel treated in atmospheres of $50%NH_3-(2,4)%CO_2-N_2-CO$ gas mixture is $48kg/mm^2$ and the depth to which residual stress is in Compressive state is $90{\mu}m$ for the atmosphere $50%NH_3-45%N_2-4%CO_2-1%CO$ gas mixture. It is consequently important to control the maximum value and size of compressive residual stress region in order to obtain desirable mechanical properties.

• Journal of Aquaculture
• /
• v.13 no.2
• /
• pp.153-161
• /
• 2000

Growth trends of 10 selected species of benthic diatoms, considered essential dietary requirement of the newly settled abalone were monitored. Navicula sp. (B-38), N. incerta and Caloneis schroderi, grew faster than the other tested diatoms. 16 and 32 % abalones fed on Raphoneis sp. and Phaeodactylum settled, respectively; less abalones souled, when fed on Navicula sp., Hantzxchia marina or Nitzschia sp. In the first experiment, survival of the settled abalone was the highest (63 %) and lowest (31 %) for those fed on Rhaphoneis sp. and Navicular sp. respectively. However, in the second and third series of esperiments, abalones fed on Rhaphoneis sp. and Navicula sp. showed the highest (67, 49 %) and lowest (35, 18 %) survival. C. schroderi proved to be the best diet, as the shell length of those fed on the diatoms was 83 ${\mu}$m, as against about 36 ${\mu}$m of those abalones, receiving H. marina or Nitzschia sp., diatoms of the lowest dietary value.

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.2E
• /
• pp.4-7
• /
• 1996

In this paper, we propose a formula to compute the exact autocorrelations of the autoregressive (AR) process. For an arbitrary value of N, we first review the Yule-Walker equation and some basic properties of the AR model. We then modify the Yule-Walker equation to construct a new system of N+1 linear equations that can be used to solve for the N+1 autocorrelation coefficients for lags 0, 1, …, N, provided that the AR parameters of order N and the power of the white noise of the AR process are given.

• Journal of the Korean Ceramic Society
• /
• v.21 no.1
• /
• pp.5-10
• /
• 1984

$eta$-Sialon synthesis was investigated via the simulataneous reduction and nitriding of Wando pyrophyllite. When Wando pyrophyllite-graphite-$Si_3N_4$ seed mixture was heated at 135$0^{\circ}C$ for as long as 10 hours in 80% $N_2$-20%$H_2$ atomsphere $eta$-$Si_3N_4$ solid solution was mainly formed together with a small amount of $\alpha$-$Si_3N_4$ The value z of the forming $Si_{6-x}Al_2O_2N{8-z}$ was decreased with heating time.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.12
• /
• pp.2039-2049
• /
• 2020

Objective: This study was conducted to provide models to accurately predict nitrogen (N) and phosphorus (P) excretion of dairy cows on smallholder farms in Indonesia based on readily available farm data. Methods: The generic model in this study is based on the principles of the Lucas equation, describing the relation between dry matter intake (DMI) and faecal N excretion to predict the quantity of faecal N (Q_FN). Excretion of urinary N and faecal P were calculated based on National Research Council recommendations for dairy cows. A farm survey was conducted to collect input parameters for the models. The data set was used to calibrate the model to predict Q_FN for the specific case. The model was validated by comparing the predicted quantity of faecal N with the actual quantity of faecal N (Q_FNACT) based on measurements, and the calibrated model was compared to the Lucas equation. The models were used to predict N and P excretion of all 144 dairy cows in the data set. Results: Our estimate of true N digestibility equalled the standard value of 92% in the original Lucas equation, whereas our estimate of metabolic faecal N was -0.60 g/100 g DMI, with the standard value being -0.61 g/100 g DMI. Results of the model validation showed that the R² was 0.63, the MAE was 15 g/animal/d (17% from Q_FNACT), and the RMSE was 20 g/animal/d (22% from Q_FNACT). We predicted that the total N excretion of dairy cows in Indonesia was on average 197 g/animal/d, whereas P excretion was on average 56 g/animal/d. Conclusion: The proposed models can be used with reasonable accuracy to predict N and P excretion of dairy cattle on smallholder farms in Indonesia, which can contribute to improving manure management and reduce environmental issues related to nutrient losses.

• Imaging Science in Dentistry
• /
• v.31 no.1
• /
• pp.1-7
• /
• 2001

Purpose : To evaluate the usefulness of the reconstructed 3-dimensional image on the personal computer in comparison with that of the CT workstation by quantitative comparison and analysis. Materials and Methods : The spiral CT data obtained from 27 persons were transferred from the CT workstation to a personal computer, and they were reconstructed as 3-dimensional image on the personal computer using V-works 2.0/sup TM/. One observer obtained the 14 measurements on the reconstructed 3-dimensional image on both the CT workstation and the personal computer. Paired Nest was used to evaluate the intraobserver difference and the mean value of the each measurement on the CT workstation and the personal computer. Pearson correlation analysis and % incongruence were also performed. Results: I-Gn, N-Gn, N-A, N-Ns, B-A, and G-Op did not show any statistically significant difference (p>0.05), B-O, B-N, Eu-Eu, Zy-Zy, Biw, D-D, Orbrd R, and L had statistically significant difference (p<0.05), but the mean values of the differences of all measurements were below 2 mm, except for D-D. The value of correlation coefficient y was greater than 0.95 at I-Gn, N-Gn, N-A, N-Ns, B-A, B-N, G-Op, Eu-Eu, Zy-Zy, and Biw, and it was 0.75 at B-O, 0.78 at D-D, and 0.82 at both Orbrd Rand L. The % incongruence was below 4% at I-Gn, N-Gn, N-A, N-Ns, B-A, B-N, G-Op, Eu-Eu, Zy-Zy, and Biw, and 7.18%, 10.78%, 4.97%, 5.89% at B-O, D-D, Orbrd Rand L respectively. Conclusion : It can be considered that the utilization of the personal computer has great usefulness in reconstruction of the 3-dimensional image when it comes to the economics, accessibility and convenience, except for thin bones and the landmarks which are difficult to be located.

• Advances in materials Research
• /
• v.13 no.3
• /
• pp.221-232
• /
• 2024

Waste tire management and recycling have grown to be significant issues because they bring up a global environmental concern. Thus, turning recycled waste tires into useful products may help tackle the environmental issue. This research aims to study and compare the effect of recycled carbon black (rCB) and commercial carbon black (CB) at certain 15 vol. % of filler loading on the mechanical, thermal, morphology and electrical properties of epoxy/CB composites. For this project, epoxy resin, diethyltoluenediamine (DETDA), recovered carbon black (rCB) and commercial carbon black (CB) graded N330, N550, N660 and N774 were mixed and compared accordingly to the formulation determined. The CB content was dispersed in the epoxy matrix using the mechanical mixing technique. The distribution and dispersion of CB in the epoxy matrix affect the characteristics of the conductive composites. rCB content at 15 vol% was selected at fixed content for comparison purposes due to the optimum value in electrical conductivity results. The flexural strength results followed the sequence of rCB>N774>N660>N550>N330. As for electrical conductivity results, epoxy/N330 exhibited the highest conductivity value, while the others achieved a magnitude of X10^-3 due to the highest external surface area of N330. In terms of thermal stability, epoxy/N330 and epoxy/N774 were slightly more stable than epoxy/rCB.

• Journal of applied mathematics & informatics
• /
• v.4 no.2
• /
• pp.513-528
• /
• 1997

A sort sequence $S_n$ is a sequence of all unordered pairs of indices in $I_n\;=\;{1,\;2,v...,\;n}$. With a sort sequence Sn we assicuate a sorting algorithm ($AS_n$) to sort input set $X\;=\;{x_1,\;x_2,\;...,\;x_n}$ as follows. An execution of the algorithm performs pairwise comparisons of elements in the input set X as defined by the sort sequence $S_n$, except that the comparisons whose outcomes can be inferred from the outcomes of the previous comparisons are not performed. Let $X(S_n)$ denote the acverage number of comparisons required by the algorithm $AS_n$ assuming all input orderings are equally likely. Let $X^{\ast}(n)\;and\;X^{\circ}(n)$ denote the minimum and maximum value respectively of $X(S_n)$ over all sort sequences $S_n$. Exact determination of $X^{\ast}(n),\;X^{\circ}(n)$ and associated extremal sort sequenes seems difficult. Here, we obtain bounds on $X^{\ast}(n)\;and\;X^{\circ}(n)$.