• E2M - 전기 전자와 첨단 소재
• /
• 제10권7호
• /
• pp.659-667
• /
• 1997

The influence of SiO$_2$on the microstructure and electrical properties of zinc oxide varistor was investigated. Zn$_2$SiO$_4$third phase in the sintered body was found at grain boundaries, multiple grain junctions, and occasionally within ZnO grains. This phase acted as a grain growth inhibitor, which retard the grain growth of the ZnO matrix by impeding migration on the grain boundaries. As SiO$_2$ addition increases, average grain size decreased from 40.6${\mu}{\textrm}{m}$ to 26.9${\mu}{\textrm}{m}$ due to the pinning effect by Zn$_2$SiO$_4$ and drag effect by Si segregation at grain boundaries, the breakdown voltage consequently increased. When SiO$_2$ addition is increased, interface state density decreased, however, the barrier height increased by decrease of donor concentration, as a result, the nonlinear exponent increased and leakage current decreased. While, as SiO$_2$ addition increase, it was found that the apparent dielectric loss factor shows a tendency of decrease. Wholly, electrical properties of zinc oxide varistor can be said to be improved by SiO$_2$addition.

• Journal of Magnetics
• /
• 제16권4호
• /
• pp.328-331
• /
• 2011

Here, we describe a dual spin valve structure with distinct switching fields for two pinned layers. A device with this structure has a staircase of three distinct magnetoresistive states. The multiple resistance states are achieved by controlling the exchange coupling between two ferromagnetic pinned layers and two adjacent anti-ferromagnetic pinning layers. The maximum magnetoresistance ratio is 7.9% for the current-perpendicular-to-plane and 7.2% for the current-in-plane geometries, with intermediate magnetoresistance ratios of 3.9% and 3.3%, respectively. The requirements for using this exchange-biased stack as a three-state memory device are also discussed.

• 한국정밀공학회지
• /
• 제21권3호
• /
• pp.188-193
• /
• 2004

The purpose of this paper is concerned with a development of an air-powered handpiece for surgical operation. The handpiece is the tool of surgical instruments and it can be used to interchange multiple attachments for drilling, pinning, sawing, driving screws and reaming. Most of domestic medical instruments bring in overseas and the air-powered handpiece imported from foreign countries at 100％ too. Therefore we develop new air powered handpiece. we research in 2D and 3D modeling, design of air line, analyze structure. The air-powered handpiece composes of body, power supply air-line, elements for mechanical power transmission, attachment, and surgical tools. The handpiece is developed by several processes that 3D design, machining, heat treatment and coating. The developed handpiece is experimented to confirm check the efficiency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1361-1363
• /
• 1997

Zinc oxide-based MOV was fabricated with $SiO_2$ additive ranging from 0.5 to 4.0 mol%, and the microstructure and electrical characteristics were investigated. $Zn_2SiO_4$ phase formed by $SiO_2$ additive was distributed at ZnO grains, grain boundaries, and multiple grain junctions. As the content of $SiO_2$ additive increases, average grain size decreased from 40.6 to $26.9{\mu}m$ due to the Pinning effect by $Zn_2SiO_4$ at grain boundaries Breakdown voltage and nonlinear exponent increased, and leakage current decreased in the range of $11.2{\sim}6.14{\mu}A$ with an increasing $SiO_2$. Donor concentration and interface state density decreased, and barrier height increased in the range of $0.71{\sim}1.04eV$ with an increasing $SiO_2$. While, as the content of $SiO_2$ additive, apparent dielectric constant decreased, peak frequency of dissipation factor decreased in the range of $6.45{\times}10^5{\sim}3.00{\times}10^5Hz$, and dissipation peak was $0.31{\sim}0.22$ at Peak frequency.

• Archives of Plastic Surgery
• /
• 제34권3호
• /
• pp.409-412
• /
• 2007

Purpose: Percutaneous Kirschner wire fixation is common method for hand fracture. It is simple but has risk of ascending infection through the pin and bony injury by multiple drilling. Ascending infection through pin tract is mostly superficial and can be treated with antibiotics and aseptic dressing. This is a case review of subacute osteomyelitis on phalangeal bones after Kirschner wire fixation with literature review. Methods: A 40-years-old man with distal phalangeal fracture on right second finger is presented. He went to a local clinic and had percutaneous Kirschner wire fixation under local anesthesia. He was transferred to our hospital for ulcerative wound on DIP joint at 4 weeks after operation. Radiography showed osteolytic change around medulla of middle and distal phalanges, leading to diagnosis of a subacute osteomyelitis. We treated it with amputation at the level of shaft of middle phalanx. Results: The postoperative course was uneventful. We thought several possible reasons for osteomyelitis in our case. First, it could resulted from ascending infection through the wire. Second, it could be resulted from a bony burn by repeated drilling. And bony necrosis could be a consequence of arterial insufficiency caused by 2 pin insertion. Conclusion: We suggest that a precise pinning based on accurate anatomical understanding is required for a percutaneous Kirschner wire fixation. The frequency of drilling should be minimized. Careful observation and patient education for pin site care are essential.

• Journal of Yeungnam Medical Science
• /
• 제20권1호
• /
• pp.28-35
• /
• 2003

대퇴골두 골단분리증으로 진단받고 수술적 치료를 받았던 14례(17 고관절)을 대상으로 이들을 1개의 나사못을 이용한 정위치고정술을 시행한 환자군(1군)과 대퇴경부 절골술 및 다발성 핀 삽입술을 함께 시행한 환자군(2군)으로 나누어 골단-간부각을 측정하여 수치를 술전, 술 후 및 마지막 추시를 비교하여 금속 내 고정술 시행 후 골단판 재형성을 확인하여 다음과 같은 결과를 얻었다. 총 14명(17 고관절) 중 6명(7 고관절)에서 골단판 재형성을 확인 할 수 있었다. 정위치고정술을 시행한 환자 11명(13례) 중, 4명(4 고관절, 평균 $7.75^{\circ}$)에서, 대퇴경부 절골술 및 다발성 핀 삽입술을 함께 시행한 환자 3명(4례) 중 2명(3 고관절, 평균 $10.7^{\circ}$)에서 골단판 재형성을 확인할 수 있었다. 골단판 재형성이 확인된 7례 중 경도의 분리가 3례(1군 3례), 중등도의 분리가 4례(1군 1례, 2군 3례)로 골단판 재형성의 빈도는 분리의 정도가 심할수록 증가되는 소견을 보였고 발병 당시 나이와는 연관성이 없었다. 골단판 재형성이 확인된 7례 중 6례에서 골단판 조기 폐쇄를 확인하였다.

• 한국정보과학회논문지:시스템및이론
• /
• 제33권9호
• /
• pp.592-607
• /
• 2006

이 논문은 실시간 제약 조건을 갖는 다중태스크 응용을 여러 개의 코어를 갖는 SoC 위에서 동작시키고자 할 때, 시스템의 비용은 최소로 하면서 성능을 높일 수 있도록 프로세서 및 하드웨어 IP를 선정하고, 태스크를 매핑 하는 기법을 제안한다. 이와 같은 기법은 하드웨어-소프트웨어 통합합성 기법이라고 한다. 이전 연구에서 우리는 복잡한 통합합성 문제를 세 가지 하부 문제(프로세서 컴포넌트 선택문제, 태스크 매핑문제, 그리고 스케줄-가능성 검사문제)로 세분화 하고, 각 문제를 독립적으로 해결하는 기법을 제안하였다[1]. 하지만 많은 장점에도 불구하고 이전 연구에서는 한 태스크가 스케줄 될 때, 자신의 스케줄-길이를 최소로 줄이기 위해 시스템 전체 자원을 모두 점유하는 것을 가정하는 제약점이 있었다. 그러나 일반적으로 보다 향상된 성능을 얻기 위해서는, 서로 관련이 없는 태스크들은 서로 다른 프로세서에서 동시에 실행될 수 있어야 한다. 이 논문에서는 다중프로세서 환경에서 다양한 운영정책을 가지는 일반적인 시스템을 위하여 태스크 매핑회피 기법과 태스크 매핑전용 기법이라는 두 가지 매핑기법을 제시한다. 멀티미디어 실시간 응용 프로그램인 다채널 디지털 비디오 레코더(Digital Video Recorder)와 관련 논문에서 제공된 임의 생성 다중태스크 예제에 대해서 큰 성능 향상을 얻을 수 있었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제25권4호
• /
• pp.19-23
• /
• 2023

The Second-generation high-temperature superconducting (HTS) Rare-Earth Barium Copper Oxide (REBCO) wire is a composite laminate having a multi-layer structure (8 or more layers). HTS wires will undergo multiple loads including the bending-tension loads during winding, high current density, and high magnetic fields. In particular, the wires are subjected to bending stress and magnetic field stress because HTS wires are wound around a circular bobbin when making a high-field magnetic. Each of the different laminated wires inevitably exhibits damage and fracture behavior of wire due to stress deformation, mismatches in thermal, physical, electrical, and magnetic properties. Therefore, when manufacturing high-field magnets and other applications, it is necessary to calculate the stress-strain experienced by high-temperature superconducting wire to present stable operating conditions in the product's use environment. In this study, the finite element model (FEM) was used to simulate the strain-stress characteristics of the HTS wire under high current density and magnetic field, and bending loads. In addition, the result of obtaining the neutral axis of the wire and the simulation result was compared with the theoretical calculation value and reviewed. As a result of the simulation using COMSOL Multiphysics, when a current of 100 A was applied to the wire, the current value showed the difference of 10^-9. The stress received by the wire was 501.9 MPa, which showed a theoretically calculated value of 500 MPa and difference of 0.38% between simulation and theoretical method. In addition, the displacement resulted is 30.0012 ㎛, which is very similar to the theoretically calculated value of 30 ㎛. Later, the amount of bending stress by the circular mandrel was received for each layer and the difference with the theoretically obtained the neutral axis result was compared and reviewed. This result will be used as basic data for manufacturing high-field magnets because it can be expanded and analyzed even in the case of wire with magnetic flux pinning.