• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.1
• /
• pp.1-9
• /
• 1993

In this paper, a new digital mobile channel has been modeled. And concatenated code systems have been proposed to transmit information reliably in the newly modeled mobile fading channels. The BCH code has been used as the outer code and the convolutional code as the inner code. We have modeled the channels which have multipath fading phenomena and additive white Gaussian noise. As a result, the characteristics of the channels are identical to that of the mobile fading channel. To find the best code system, we have tested (7, 4), (63, 45), (63, 57) and (31.26) BCH codes as an outer code. Results show that the concatenated code with (7, 4) outer code gives the best performance. And if we use the soft decision, we can improve about 2 -6 dB in the SNR

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.1
• /
• pp.9-15
• /
• 2011

Communication environments in the context of underwater channel are characterized to be bad by the characteristics of multipath. Multipaths are affected by various factors e.g. the temperature and the salinity of the ocean. In this paper, the representative sound speed profiles were calculated in the southern part of Baengnyeoung island so that the eigen-ray paths with the channel impulse responses were determined using the average sound speed profile of last decade. The performance of underwater communication was analyzed using the BPSK modulation and time reversal method. The significant differences of results were shown according to the change of season and carrier frequency by using computer simulation. In addition, improved performance is obtained using preprocess channel impulse response for the better comparison of two cases of summer and autumn.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.3
• /
• pp.63-68
• /
• 2014

This paper related with the I-CMA (Improved-CMA) algorithm that is possible to compensates of phase in CMA adatpve equalizer which is used for the elemination of intersymbol interference in the multipath fading and band limit characteristics of channel. The new cost function is proposed for the eliminate the amplitude and phase simulataneous by modifying the cost fuction for get the error signal in present CMA algorithm. It has a merit to the algorithm simplicities and eliminats the PLL device for phase compensation after equalization. For proving this, the recovered signal constellation that is the output of equalizer output signal and the residual isi and Maximum Distortion charateristic learning curve that are presents the convergence performance in the equalizer and the overall frequency transfer function of channel and equalizer were used. As a result of computer simulation, the I-CMA has more good compensation capability of amplitude and phas in the recovered constellation. But the convergence time is slow due to the simultaneously phase compensation.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.4
• /
• pp.12-19
• /
• 2016

The monitoring system in railway is under study to forecast any derailment and accident by defect of train. Because the monitoring system is composed of wireless sensor network based on ZigBee-communication between inside and outside of train, the study for wireless channel analysis is required. Especially, if multipath delay profile exist in the channel, the equalizer and channel estimator can be required for preventing receiver performance degradation. Therefore, we analyzed the wireless channel in train environment using measured data and, proposed the channel estimation method through the characterisitic of chip code, under the consideration of the channel characteristics in train. To show the performance of proposed method, we demonstrate the performance by mean square error(MSE), computational complexity and bit error rate(BER).

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.1
• /
• pp.21-30
• /
• 2018

A passive time-reversal technique can improve error performance of the underwater communication system by reducing influence of inter-symbol interferences, which is caused by a multipath channel response. The passive time-reversal communication system equipped with numerous receivers generally can obtain superior error performance since larger diversity gain can be obtained as the number of available received signal increased. In this paper, we analyze the optimal number and combination of receivers that can approximately achieve the best error performance when using the limited number of receivers. For this analysis, we use communication data collected during SAVEX15 (Shallow-water Acoustic Variability Experiment 2015) carried out in the south-western part of Jeju Island from May 14 to May 28, 2015. Analysis results show that there are depths of energy concentration due to the channel characteristics in which the underwater sound channel are present, and the passive time-reversal technique using the limited number of the receivers can derive near-optimal communication performance if the receivers for time-reversal processing are located at the depths where energy is concentrated.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1577-1582
• /
• 2013

In this paper, we have analyzed the performance of MIMO (Multi-Input Multi-Output) underwater acoustic communication by using the acquired data via the experiments in water tank. First of all, in the pursuit of this aim, we have measured the channel transfer characteristics at several transceiver locations. The transmitted signal was modulated by QPSK(Quadrature Phase Shit Keying) and the received signal was recovered through the detector that contains the zero forcing equalizer. A maximum 30~40 ms delay was appeared because of physically closed water tank environment that has the harsh multi-path transmission conditions. In result of experiment, even though the bit error rate showed comparatively large when $2{\times}2$ MIMO system with two transmitters and receivers was considered. However, we confirmed it has approximately 15% enhanced performance compared with SISO (Single-Input Single-Output) system.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.8
• /
• pp.1911-1932
• /
• 2013

Orthogonal frequency-division multiplexing (OFDM) has become a popular modulation scheme for wireless protocols because of its spectral efficiency and robustness against multipath interference. Although the components of various OFDM protocols are functionally similar, they remain distinct because of the characteristics of the environment. Recently, graphics processing units (GPUs) have been used to accelerate the signal processing of the physical layer (PHY) because of their great computational power, high development efficiency, and flexibility. In this paper, we describe the implementation of parameterized baseband modules using GPUs for two different OFDM protocols, namely, 802.11a and 802.16. First, we introduce various modules in the modulator/demodulator parts of the transmitter and receiver and analyze the computational complexity of each module. We then describe the integration of the GPU-based baseband modules of the two protocols using the parameterized method. GPU-based implementations are addressed to explain how to accelerate the baseband processing to archive real-time throughput. Finally, the performance results of each signal processing module are evaluated and analyzed. The experiments show that the GPU-based 802.11a and 802.16 PHY meet the real-time requirement and demonstrate good bit error ratio (BER) performance. The performance comparison indicates that our GPU-based implemented modules have better flexibility and throughput to the current ones.

• The Journal of the Acoustical Society of Korea
• /
• v.33 no.3
• /
• pp.174-183
• /
• 2014

When a active sonar signal is transmitted and returned back from a target, it has been distorted by various properties of acoustic channel such as multipath arrivals. And signals have been appeared to be different form by target position and attitude. Therefore, we simulated the target echo signal using 3 dimensional target model include reflects target features. In this paper, we develop components form of a simulated target model is made up equally spaced highlight points, and each part of the target consists of shape function. We can simulate a target echo signal and Target strength (TS) according to wave incident angle. To verify, we made small scale target in kit form and we had got underwater target signal for comparing simulation result in water tank.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.9 s.339
• /
• pp.19-28
• /
• 2005

We establish a statistical model for the ultra-wide bandwidth (UMB) indoor channel based on over 2000 frequency response measurements campaign in a Practical apartment. The approach is based on the investigation of the statistical properties of the multipath profiles measured in different place with different rooms. Based on the experimental results, a characterization of the propagation channel from theoretic view point is described. Also we describe a method for measurement of the channel impulse response and channel transfer function. Using the measured data, the authors compares channel impulse responses obtained from time-domain and channel transfer functions obtained from frequency-domain with statistical path loss model. The bandwidth of the signal used in this experiment is from 10MHz to 8.01 GHz. The time-domain results such as maximum excess delay, men excess delay and ms delay spread are presented. As well as, omni-directional biconical antenna were used for transmitter and receiver In addition, measurements presented here support m channel model including the antenna characteristics.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.5 no.4
• /
• pp.47-63
• /
• 1994

An important parameter in characterizing mobile communication channel is delay spread. This paper presents the results of measured delay profiles and calculated distribution funcations of delay spread for typical cellular service environments at Taejon and vicinities. The measurement system uses 1023 chip length, 5 Mbps PN code and sliding correlation method. It has been evaluated by using commercial hardware channel simulator for reliability of out data. As results the value of mean delay spread is 2.08 $\mu\textrm{s}$for suburban area. 2.12 $\mu\textrm{s}$ for urban area and 1.3 $\mu\textrm{s}$ for national/local road. Delay spread is less then 3.4$\mu\textrm{s}$, 2.8$\mu\textrm{s}$ and 1.5 $\mu\textrm{s}$ for probability of 50% and 4.5$\mu\textrm{s}$, 4.2$\mu\textrm{s}$ and 2.9$\mu\textrm{s}$ for probability of 90% at each tested site. The difference of delay spread is within 7% between going and returning status along same street. In this experiment, we found delay spread for suburban area is larger than reported foreign test results.