• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.365-370
• /
• 1997

In this paper we suggest a development of surface defect inspection algorithms for cold mill strip using tree structure. The defects which exist in a surface of cold mill strip have a scattering or singular distribution. This paper consists of preprocessing, feature extraction and defect classification. By preprocessing, the binarized defect image is achieved. In this procedure, Top-hit transform, adaptive thresholding, thinning and noise rejection are used. Especially, Top-hit transform using local min/max operation diminishes the effect of bad lighting. In feature extraction, geometric, moment, co-occurrence matrix, histogram-ratio features are calculated. The histogram-ratio feature is taken from the gray-level image. For the defect classification, we suggest a tree structure of which nodes are multilayer neural network clasifiers. The proposed algorithm reduced error rate comparing to one stage structure.

• Journal of the Korean Magnetics Society
• /
• v.23 no.4
• /
• pp.122-125
• /
• 2013

Perpendicular magnetic anisotropy (PMA) is the phenomenon of magnetic thin film which is preferentially magnetized in a direction perpendicular to the film's plane. Amorphous multilayer with PMA has been studied as the good candidate to realization of high density STT-MRAM (Spin Transfer Torque-Magnetic Random Access Memory). The current issue of high density STT-MRAM is a decrease in the switching current of the device and an application of amorphous materials which are most suitable devices. The amorphous ferromagnetic material has low saturated magnetization, low coercivity and high thermal stability. In this study, we presented amorphous ferromagnetic multilayer that consists of an amorphous alloy CoSiB and a nonmagnetic material Pd. We investigated the change of PMA of the $[CoSiB\;t_{CoSiB}/Pd\;1.3nm]_5$ multilayer ($t_{CoSiB}$ = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6 nm, and $t_{Pd}$ = 1.0, 1.1, 1.2, 1.3, 1.4, 1.5, 1.6 nm) and $[CoSiB\;0.3nm/Pd\;1.3nm]_n$ multilayer (n = 3, 5, 7, 9, 11, 13). This multilayer is measured by VSM (Vibrating Sample Magnetometer) and analyzed magnetic properties like a coercivity ($H_c$) and a magnetization ($M_s$). The coercivity in the $[CoSiB\;t_{CoSiB}\;nm/Pd\;1.3nm]_5$ multi-layers increased with increasing $t_{CoSiB}$ to reach a maximum at $t_{CoSiB}$ = 0.3 nm and then decreased for $t_{CoSiB}$ > 0.3 nm. The lowest saturated magnetization of $0.26emu/cm^3$ was obtained in the $[CoSiB\;0.3nm/Pd\;1.3nm]_3$ multilayer whereas the highest coercivity of 0.26 kOe was obtained in the $[CoSiB\;0.3nm/Pd\;1.3nm]_5$ mutilayer. Additional Pd layers did not contribute to the perpendicular magnetic anisotropy. The single domain structure evolved in to a striped multi-domain structure as the bilayer repetition number n was increased above 7 after which (n > 7) the hysteresis loops had a bow-tie shapes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.802-805
• /
• 2003

Structural surface becomes an antenna. The integration of antennas into structural body panels is a new high payoff technology. It emerged from the need to improve structural efficiency and antenna performance. In this paper, we developed new design concept for the structural surface which transmits and receives the electromagnetic signals, and it is termed Surface-Antenna-Structure (SAS). Design procedure was presented including structure design. material selection and design of antenna elements, which was processed according to the communication with KORSAT satellite at Ku-Band (12.25-12.75 GHz). The final demonstration article was 350$\times$200$\times$7.5mm flat antenna panel. Experimental results for antenna performances were in good agreements with design requirements. Also structural analysis was performed with SAS. estimating stress distributions under simply supported condition with Laminated Plate Theories and Wavier Solutions. The SAS concept can be extended to give a useful guide to manufacturers of structural body panels as well as antenna designers. promising innovative future communication technology.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.179-183
• /
• 2001

Magnetoresistance and Planar Hall effect of Glass/Ni$\sub$83/Fe$\sub$17/(2 nm)/[Cu(2 nm)Ni$\sub$83/Fe$\sub$17/(20 nm)]$\sub$50/ multilayer were measured. Repeated saw tooth like planar Hall effect signal was observed in the range of magnetization reversal process, while no sign of such saw tooth was observed in Magnetoresistance diagram. For the reason of saw tooth like signal, it is supposed that subsequent abrupt domain wall motion of each magnetic layer in the process of magnetization reversal process was observed in planar Hall effect in transverse direction to the current direction. This fine structure of planar Hall effect was observed for applied fields in any direction. Magnetoresistance curve did not show this fine structure of magnetization reversal, of course, since only net magnetization of each layer has to do with the resistivity. Extended research on the reason of this sawtooth like signal should be conducted.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.61-68
• /
• 1999

To analyze several defects and residual stress in sintering of layer structure materials, multiayer materials with TZP/SUS and ZT/SUS, and bilayer materials with porcelain/alumina and porcelain/Y-TZP were fabricated by sintering method. Multilayer materials prepared by pressureless sintering show the sintering defect such as warping, splitting, cracking originated from the difference of sintering shrinkage between each layer, which could be controlled by the adjustment of number and thickness in interlayer. In tape casting, a certain pressure given during sintering relaxed the sintering defects, specially warping. The residual stress in bilayer was examined with Vickers indentation method. A small tensile stress in porcelain/alumina and a large compressive stress in porcelain/Y-TZP were generated on the porcelain interface due to the thermal expansion mismatch, which affected the strength of bilayer materials. As a consequence, the sintering defects of multilayer materials and the residual stresses of bilayer materials were dominantly influenced on material design and starting material constants.

• Applied Chemistry for Engineering
• /
• v.31 no.3
• /
• pp.291-298
• /
• 2020

ZITO/Ag/ZITO multilayer transparent electrodes at room temperature on glass substrates were prepared using RF/DC magnetron sputtering. Transparent conductive films with a sheet resistance of 9.4 Ω/㎡ and a transmittance of 83.2% at 550 nm were obtained for the multilayer structure comprising ZITO/Ag/ZITO (100/8/42 nm). The sheet resistance and transmittance of ZITO/Ag/ZITO multilayer films meant that they would be highly applicable for use in polymer-dispersed liquid crystal (PDLC)-based smart windows due to the ability to effectively block infrared rays (heat rays) and thereby act as an energy-saving smart glass. Effects of the thickness of the PDLC layer and the intensity of ultraviolet light (UV) on electro-optical properties, photopolymerization kinetics, and morphologies of difunctional urethane acrylate-based PDLC systems were investigated using new transparent conducting electrodes. A PDLC cell photo-cured using UV at an intensity of 2.0 mW/c㎡ with a 15 ㎛-thick PDLC layer showed outstanding off-state opacity, good on-state transmittance, and favorable driving voltage. Also, the PDLC-based smart window optimized in this study formed liquid crystal droplets with a favorable microstructure, having an average size range of 2~5 ㎛ for scattering light efficiently, which could contribute to its superior final performance.

• Applied Chemistry for Engineering
• /
• v.33 no.1
• /
• pp.50-57
• /
• 2022

Ti-In-Zn-O (TIZO)/Ag/TIZO multilayer transparent electrodes were prepared on glass substrates at room temperature using RF/DC magnetron sputtering. Obtained multilayer structure comprising TIZO/Ag/TIZO (10 nm/10 nm/40 nm) with the total thickness of 60 nm showed a transmittance of 86.5% at 650 nm and a sheet resistance of 8.1 Ω/□. The multilayer films were expected to be applicable for use in energy-saving smart window based on polymer-dispersed liquid crystal (PDLC) because of their transmittance properties to effectively block infrared rays (heat rays). We investigated the effects of the content ratio of prepolymer, the thickness of the PDLC coating layer, and the ultraviolet (UV) light intensity on electro-optical properties, and the surface morphology of polyester acrylate-based PDLC systems using new TIZO/Ag/TIZO transparent conducting electrodes. A PDLC cell with a thickness of 15 ㎛ PDLC layer photocured at an UV intensity of 1.5 mW/cm² exhibited good driving voltage, favorable on-state transmittance, and excellent off-haze. The LC droplets formed on the surface of the polymer matrix of the PDLC composite had a size range of 1 to 3 ㎛ capable of efficiently scattering incident light. Also, the PDLC-based smart window manufactured using TIZO/Ag/TIZO multi-layered transparent electrodes in this study exhibited a light brown, which will have an advantage in terms of aesthetics.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.3
• /
• pp.18-24
• /
• 2003

The resonator using two layer microstrip structure was proposed and the bandpass filter was designed using this resonator in this paper. The proposed resonator structure is constructed by placing a U-shape of resonator in the first layer and then placing a broadside coupling strip in the second layer just above of the U-shape of resonator's edge part. Because these structure has various design parameters than general single layer coupled line structure, filter design is more flexible. In this paper, the narrow band filter was designed using multi-layer structure that had been applied to broadband filter because it's high coupling nature. The filter was designed to have 4MHz center frequency and 3 % fractional bandwidth, and finally confirmed that can be realizable narrow band filter by using multi-layer structure through fabrication and measurement.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.11
• /
• pp.34-42
• /
• 1997

In this paper, we show an optimal structure of impedance control in high density layouts ina high multilayers PCB. The impedance control in a high multilayers FR-4 PCB is very portant isue because a dielectric layer's thickness is very thin. Especially, odd mode impedance control is more difficult than characteristic impedance control in high multilayers PCB. So, we show an optimal structure of odd mode impedance control in that dielectric thickness is about 0.1mm with limited state and discuss multilayers PCB's for swich circuti pack and backplane in developing algorith scale ATM witching system in next time.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.4
• /
• pp.499-505
• /
• 1998

In developing an automated surface inspect algorithm, we have designed a hierarchical classifier using neural network. The defects which exist on the surface of cold mill strip have a scattering or singular distribution. We have considered three major problems, that is preprocessing, feature extraction and defect classification. In preprocessing, Top-hit transform, adaptive thresholding, thinning and noise rejection are used Especially, Top-hit transform using local minimax operation diminishes the effect of bad lighting. In feature extraction, geometric, moment, co-occurrence matrix, and histogram ratio features are calculated. The histogram ratio feature is taken from the gray-level image. For defect classification, we suggest a hierarchical structure of which nodes are multilayer neural network classifiers. The proposed algorithm reduced error rate by comparing to one-stage structure.