• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.4
• /
• pp.378-387
• /
• 1994

To improve the properties of $PbTiO_3$ thin films successfully grown by thermal diffusion of 3 component layers of $Ti0_2/Pb/TiO_2(900{\AA}/900{\AA}/900{\AA})$ in preceding research, 3, 5, 7, 9, and 11 multilayer structures $(TiO_2/Pb/.../Tio_2)$ with thinner component layer of $200~300 {\AA}$ thick were deposited on Si substrate by RF sputtering, which were followed by RTA to form $PbTiO_3$ thin films. As a result, $PbTiO_3$ single phase was formed above $500^{\circ}C$. When the thickness of component layer reduced and the number of component layers increased, suppression of Pb-silicate and voids formation resulted in relatively sharp interfaces and the film composition became more homogeneous. Relative dielectric constants in MIM structure were independent of the annealing condition, but they increased with increasing thickness of the $PbTiO_3$ thin films. The maximum breakdown field in MIS structure reached 150kV/cm.

• Journal of the Korean Magnetics Society
• /
• v.14 no.5
• /
• pp.192-195
• /
• 2004

Magnetic properties by exchange biased perpendicular magnetic anisotropy in [Pd(0.8 nm)/Co(0.8 nm)]$_{5}$/FeMn(15 nm) multilayers deposited by dc magnetron sputtering system are investigated. As inserted Pd layer of interface between [Pd/Co] multilayer and FeMn film, the Hex of perpendicular anisotropy was improved from 127 Oe to 145 Oe. But result of an experiment by thermal stability, the Hex of the case that an inserted layer was inserted in decreased from low 20$0^{\circ}C$ in about 5$0^{\circ}C$ more if not inserted. If Ta was a buffer layer, the experiment results along material of buffer layer, the H$_{ex}$ obtained the largest 127 Oe. And if Pd was a buffer layer, H$_{ex}$ obtained the largest 169 Oe. Also, the Hc in buffer layer of Ta and Pd obtained the largest 203 Oe and 453 Oe, respectively.

• Journal of the Korean Magnetics Society
• /
• v.19 no.2
• /
• pp.52-56
• /
• 2009

Interlayer coupling field, coercivity, magnetoresitance ratio, and magnetic sensitivity depending on the thickness of free CoFe layer for the CoFe/Cu/CoFe/IrMn multilayer are investigated. In case of CoFe layer of $30\;{\AA}$ thickness for the CoFe(t)/Cu($25\;{\AA}$)/CoFe($60\;{\AA}$)/IrMn($80\;{\AA}$) multilayer with ferromagnet/non-magnet/ferromagnet structure induced by IrMn layer, the lowest coercivity and the highest magnetic sensitivity, which is contained soft magnetic property, are observed. On the other side, in case of CoFe layer of $90\;{\AA}$ thickness, there are the highest coercivity and the lowest magnetic sensitivity. The fabricated CoFe($30\;{\AA}$)/Cu($25\;{\AA}$)/CoFe($60\;{\AA}$)]/IrMn($80\;{\AA}$) spin valve device with $2{\times}8{\mu}m^2$ patterning size are measured by two probe method, which is selected the sensing current as the longitudinal direction and the easy axis as the transversal direction. The measuring magntoresistance ratio and magnetic sensitivity of GMR-SV device having the soft magnetic property are 3.0% and 0.3%/Oe, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.66-66
• /
• 2008

본 연구에서는 ITO/Ag/ITO 다층 박막을 유기발광소자와 플렉시블 광전소자의 전극으로 적용하기 위하여 선형 대항 타겟 스퍼터(Linear facing target sputter) 시스템을 이용하여 성막하였고, ITO/Ag/ITO 다층박막의 전기적, 광학적, 구조적 특성을 분석하였다. 선형 대항 타겟 스퍼터 시스템은 강한 일방항의 자계와 타겟에 걸린 음극에 의해 전자의 회전, 왕복 운동이 가능해 마주보는 두 ITO 타겟 사이에 고밀도의 플라즈마를 구속 시켜 플라즈마 데미지 없이 산화물 박막을 성막시킬 수 있는 장치이다. 대항 타겟 스퍼터 시스템을 이용하여 성막한 ITO 전극을 DC power, working pressure, Ar/O2 ratio 에 따른 특성을 각각 분석하였다. glass 기판위에 최적화된 ITO 전극을 bottom layer로 두고, bottom ITO layer 위에 thermal evaporation 을 이용하여 Ag 박막을 6~20nm의 조건에 따라 두께를 다르게 성막하고, Ag 박막을 성막한 후에 다시 bottom ITO 전극과 같은 조건으로 ITO 전극을 top layer로 성막 하였다. 두 비정질의 ITO 전극 사이에 매우 앓은 Ag 박막을 성막 함으로 해서 glass 기판위에 ITO/Ag/ITO 다층 박막전극은 매우 낮은 저항과 높은 투과도를 나타낸다. ITO/Ag/ITO 박막의 전기적 광학적 특성을 보기 위해 hall measurement와 UV/visible spectrometer 분석을 각각 진행하였다. ITO/Ag/ITO 다층 박막 전극이 매우 얇은 두께임에도 불구하고 $4\Omega$/sq.의 낮은 면저항과 85%의 높은 투과도를 나타내는 이유는 ITO/Ag/ITO 전극 사이에 있는 Ag층의 표면 플라즈몬 공명 (SPR) 현상으로 설명할 수 있다. ITO/Ag/ITO 전극의 Ag의 거동을 분석 하기위해 FESEM분석과 synchrotron x-ray scattering 분석을 하였다. ITO/Ag/ITO 전극의 Ag층이 islands의 모양에서 연속적으로 연결되는 변화과정 중에 SPR현상이 일어남을 알 수 있다. 여기서, 대항 타겟 스퍼터 시스템을 이용하여 성막한 ITO/Ag/ITO 다층박막을 OLED 또는 inverted OLEDs의 top 전극으로의 적용 가능성을 보이고 있다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.173-173
• /
• 2010

$Bi_4Ti_3O_{12}$ ($B_4T_3$) is a unique ferroelectric material that has a relatively high dielectric constant, high Curie temperature, high breakdown strength, and large spontaneous polarization. As a result this material has been widely studied for many applications, including nonvolatile ferroelectric random memories, microelectronic mechanical systems, and nonlinear-optical devices. Several reports have appeared on the use of Mn dopants to improve the electrical properties of $B_4T_3$ thin films. Mn ions have frequently been used for this purpose in thin films and multilayer capacitors in situations where intrinsic oxygen vacancies are the major defects. However, no systematic study of the optical properties of $B_4T_3$ films has appeared to date. Here, we report optical data for these films, determined by spectroscopic ellipsometry (SE). We also report the effects of thermal annealing and Mn doping on the optical properties. The SE data were analyzed using a multilayer model that is consistent with the original sample structure, specifically surface roughness/$B_4T_3$ film/Pt/Ti/$SiO_2$/c-Si). The data are well described by the Tauc-Lorentz dispersion function, which can therefore be used to model the optical properties of these materials. Parameters for reconstructing the dielectric functions of these films are also reported. The SE data show that thermal annealing crystallizes $B_4T_3$ films, as confirmed by the appearance of $B_4T_3$ peaks in X-ray diffraction patterns. The bandgap of $B_4T_3$ red-shifts with increasing Mn concentration. We interpret this as evidence of the existence deep levels generated by the Mn transition-metal d states. These results will be useful in a number of contexts, including more detailed studies of the optical properties of these materials for engineering high-speed devices.

• Journal of the Korean Magnetics Society
• /
• v.5 no.1
• /
• pp.42-47
• /
• 1995

FeN thin films for inductive recording heads were sputter deposited using RF diode sputtering mehtod from a pure iron target onto 7059 glass substrates, and their magnetic properties were measured. The magnetic properties were greatly affected by film thickness, gas pressure, sputter power and flow ratio of $N_{2}$ to Ar. Single layer FeN films with their thickness varied from $1,000\;{\AA}$ to $6,000\;{\AA}$ were doposited. 800 W sputter power, 3 mT gas pressure, $N_{2}$ to Ar flow ratio of 6.6 : 100 were the sputtering conditions. Up to 7 layers of FeN films having total thickness of $6,000\;{\AA}$ were deposited using $SiO_{2}$ of $30\;{\AA}$ thickness as intermediate layers and their coercivity and saturation magnetization were measured. The sputtering conditions were the same as those in the single layer films. Easy axis coercivity of the single layer FeN films gradually decreased as their thickness was increased, but for the films with their thicknesses above $3,000\;{\AA}$, the coercivity changed very little. As the number of the FeN layers were increased, the coercivity decreased We estimated the grain size of FeN films from the FWHM (Full Width at Half Maximum) of X-ray diffraction peaks. The grain size steadily decreased from about $200\;{\AA}$ to $120\;{\AA}$ as the number of layers were increased. Minimum hard axis coercivity of 0.4 Oe was obtained when the number of layers was four. Maximum relative permeability was 2,900 when the number of layers was three. The cut off frequeocy of the multilayer films were above 100 MHz.

• Food Science of Animal Resources
• /
• v.32 no.4
• /
• pp.483-490
• /
• 2012

Ready-to-eat chicken breasts were packaged in a multilayer, gas-tight tray with top film and various quality changes were investigated during the 24 wk of storage at $10^{\circ}C$. Over the storage period, total aerobes, mesophilic aerobic and anaerobic spore formers, and Clostridium spp. were not detected above 1.0 log CFU/g (detection limit). The residual oxygen ratio in the head space of tray and pH values tended to decrease with storage time, namely from initial values of 5.7% and 6.56 to 3.3% and 6.34 at week 24, respectively. Thiobarbituric acid reactive substances and volatile basic nitrogen values increased from 0.52 mg malonaldehyde (MA)/kg and 2.1 mg/100 g initially, to 3.70 mg MA/kg and 39.9 mg/100 g at week 24, respectively. In terms of the change in meat color during storage, the samples showed a slight increasing trend of CIE $a^*$, $b^*$, and ${\Delta}E$ values over the storage period until week 24 (p<0.05). The change in brine color showed a similar trend with meat of which Hunter $b^*$ and ${\Delta}E$ values increased slightly during storage during 24 wk (p<0.05). The values for the transmittance degree of brine in the samples tended to decrease. Moreover, values for the absorbance degree tended to increase with storage time until week 24. The sensory scores for color, texture, odour, and flavour were evaluated below 5.0 (marketability level) after 24 wk of storage. Based on this sensory evaluation, it could be concluded that retorted RTE chicken breast could remain marketable for at least 20 wk at $10^{\circ}C$.

• Korean Journal of Optics and Photonics
• /
• v.33 no.4
• /
• pp.177-186
• /
• 2022

The performance of a surface plasmon resonance sensor is evaluated based on the sensitivity (nm/RIU) and sharpness from the full width at half maximum (FWHM) and the peak depth of a resonance peak. These factors are determined by the materials and conformational properties of the sensing structure. In this paper, we investigated an optimized insulator-metal-insulator (IMI) multilayer-based surface plasmon resonance sensor structure to simultaneously achieve high sensitivity, narrow FWHM, and deep peak depth while using gold for the metallic film layer which occurs peak broadening. By adopting the optimized structure, sensitivity of 8,390 nm/RIU, FWHM of 11.92 nm, and a resonance peak depth of 93.1% were achieved for 1.45-1.46 refractive index variation of the sensing layer. With the suggested structure conformation, high sensitivity and resolution of sensing performance can be achieved.

• Journal of the Korean Magnetics Society
• /
• v.6 no.3
• /
• pp.158-164
• /
• 1996

The magnetic and magneto-optical properties of the Tb/Co multilayers as a function of the layer thickness and the ratio of Tb/Co thicknesses were studied. When the thickness of Tb layer was $12{\AA}$, the maximum perpendicular anisotropy energy and the maximum thickness ratio which displays the perpendicular anisotropy were obtained. This result indicated that the Tb-Tb and Co-Co pairs as well as the Tb-Co pairs contribute to the perpendicular anisotropy. The Kerr rotation angle, $({\theta}_k)$ was proportional to the perpendicular anisotropy energy and was inversely proportional to the average spin dispersion angle, $(\alpha)$. The maximum $({\theta}_k)$ of $0.28^{\circ}$ was obtained in the film of $12{\AA}$ Tb and the thickness ratio of 1.55. The abnormal hysteresis loops were appeared during the aging treatment because the coercivity difference between the Co layer and the Tb layer was increased by the preferential oxidation of Tb.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.410-420
• /
• 2006

The dynamic effects, such as the steering and the screening effects during deposition on an epitaxial growth is studied by kinetic Monte Carlo simulation. In the simulation, we incorporates molecular dynamic simulation to rigorously take the interaction of the deposited atom with the substrate atoms into account, We find three characteristic features of the surface morphology developed by grazing angle deposition: (1) enhanced surface roughness, (2) asymmetric mound, and (3) asymmetric slopes of mound sides, Regarding their dependence on both deposition angle and substrate temperature, a reasonable agreement of the simulated results with the previous experimental ones is found. The characteristic growth features by grazing angle deposition are mainly caused by the inhomogeneous deposition flux due to the steering and screening effects, where the steering effects play the major role rather than the screening effects. Newly observed in the present simulation is that the side of mound in each direction is composed of various facets instead of all being in one selected mound angle even if the slope selection is attained, and that the slope selection does not necessarily mean the facet selection.