• Journal of Power Electronics
• /
• 제15권5호
• /
• pp.1178-1189
• /
• 2015

A non-isolated Multiple Input Converter (MIC) with an input port, two storage ports and a load port is proposed. The synthesis of the proposed four port converter with its switch realization is presented. A steady state analysis of each operating mode with a small-signal model is derived, and a stability analysis is done. A mode selection controller is proposed to automatically choose a specific operating mode based on the voltage levels of the different source and storage units. In addition, a voltage control loop is used to regulate the output voltage. A 200W prototype is built with a TMS320F28027 DSP controller to test the feasibility of the operating modes. Simulation and experimental results show the ability of the proposed converter to handle multiple inputs either individually or simultaneously.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.410-411
• /
• 2011

본 논문에서는 태양광 전원, 배터리, 마이크로터빈, 스마트 홈 등 다양한 목적과 특성을 가진 요소로 구성된 마이크로그리드를 효율적으로 제어, 관리하기 위한 분산 지능형 제어원리를 제안한다. 기존의 중앙집중식 제어원리는 중앙에서 전체 시스템에 대한 정보를 취득하여 운영에 대한 의사결정을 독점하는 구조였다면 제안하는 원리는 마이크로그리드의 구성요소가 각각 지능형 에이전트를 기반으로 스스로 데이터를 취득하고 이웃 에이전트와의 대화와 협조를 통해 분산제어를 수행하는 방식이다. 각 에이전트 사이는 근거리 무선통신 방식인 Zigbee를 이용하였고 마이크로그리드를 실시간으로 해석하기 위하여 MATLAB 기반의 실시간 시뮬레이터를 이용하였다. 실시간 마이크로그리드 시뮬레이션 모델과 에이전트 역할을 하는 마이크로 컨트롤러를 연계하여 Hardware-in-the-loop 기반의 데모시스템을 구축하였고 제안하는 원리에 대해 검증하였다.

• Journal of Power Electronics
• /
• 제18권4호
• /
• pp.1235-1244
• /
• 2018

The application of shunt capacitor banks and underground cables typically induces resonance in power distribution systems. In this study, the propagation of resonance in a microgrid (MG) with inverter-based distributed generators (IBDGs) is investigated. If resonances are not properly damped, then the output current of the inverters may experience distortion via resonance propagation due to the adverse effect of resonances on MG power quality. This study presents a conceptual method for identifying resonances and related issues in multi-inverter systems. For this purpose, existing resonances are identified using modal impedance analysis. However, some resonances may be undetectable when this method is used. Thus, the resonances are investigated using the proposed method based on the frequency response of a closed-loop MG equivalent circuit. After analyzing resonance propagation in the MG, an effective virtual impedance damping method is used in the IBDG control system to damp the resonances. Results demonstrate the effectiveness of the proposed method in compensating for existing resonances.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집(한일합동학술편); 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.780-785
• /
• 1987

The measuring point data of clay model are widely used to design parts whose external features are important design factor such as automobiles and general die products. This paper presents a method for improving the process to generate smooth surfaces from the measuring point data using turnkey CAD/CAM system. The process of smooth-surface generation involves several steps: styline finding, curve fairing, surface generation and filleting. The process is improved by automatic curve fairing, local correction of surface and multi-boundary surface treatment. An automobile bumper and a telephone receiver are measured and modeled to test the new method. Significant time saving is resulted by changing interactive mode to automatic mode and eliminating inefficient loop of surface generation process.

• 전력전자학회논문지
• /
• 제20권1호
• /
• pp.38-44
• /
• 2015

This paper presents the sensorless drive method for mono inverter dual parallel (MIDP) surface mounted permanent magnet synchronous motor (SPMSM) drive system. MIDP motor drive system is a technique that can reduce the cost of the multi motor driving system. To maximize this merit of the MIDP motor drive system, the sensorless technique is essential to eliminate the position sensors. This paper adopts an appropriate sensorless method for MIDP SPMSM drive system, which uses the reduced order observer and phase locked loop (PLL) to reduce the calculation burden. The I-F control method is implemented for start-up and low speed operation. The validity and performance of the proposed algorithm are shown via experiments with 600-W SPMSMs.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 추계학술대회 논문집
• /
• pp.124-126
• /
• 2004

This paper describes a boost converter cascaded high frequency link direct do-ac converter suitable for fuel cell power sources. A new multi-loop control for a boost converter to reduce the low frequency input current harmonics drawn from fuel cell is proposed. A new PWM technique for the cycloconverter at the secondary to reject the low order harmonics in the output voltages is presented in detail.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 학술대회 논문집
• /
• pp.245-249
• /
• 2005

This paper describes a boost converter cascaded high frequency link direct dc-ac converter suitable for fuel cell power sources. A new multi-loop control for a boost converter to reduce the low frequency input current harmonics drawn from fuel cell is proposed. A new PWM technique for the cycloconverter at the secondary to reject the low order harmonics in the output voltages is presented in detail.

• 대한기계학회논문집B
• /
• 제24권9호
• /
• pp.1195-1209
• /
• 2000

The purpose of this study is to develop the non-gravity fluidized dryer. In this non-gravity fluidized dryer the fluidized zone is produced by two paddles in mixer, which maximizes the surface area of materials and then heated air through the guiding panels dehumidify them. This can conduct the drying process quickly and control moisture contents to lower limits. The ventilation system is closed loop system, which can be changeable to open system, and can be used as a multi-purposed dryer in which mixing, drying, granulating and cooling process is conducted. In order to develop the non-gravity fluidized dryer, in the first fundamental experiments were performed to mixing accuracy and then the other parts of dryer and control system were examined to check whether they were designed properly and operated harmoniously with mixer. Also the preparatory experiments were fulfilled to examine the efficiency and reliability of the dryer. Lastly, on the basis of preparatory experiments, performance test for the non-gravity fluidized dryer carried out for the variation of the initial moisture contents, desired moisture contents, heated air velocity and heating temperature.

• 한국지능시스템학회논문지
• /
• 제5권3호
• /
• pp.64-72
• /
• 1995

본 논문에서는 공정제어계의 PI제어기의 이득을 동조하는 방법을 다룬다. 산업계에서 사용되고 있는 제어기는 PI형이고, 이의 이득은 숙련조업자에 의하여 시행착오법으로 조정되고 있다. 따라서 제어기의 동조에는 많은 시간과 노력이 소요되며 다중루프를 갖는 공정의 경우에는 동조하기가 매우 어려운 실정이다. 본 논문에서는 다루는 퍼지동조기는 아래와 같은 가정하에서 개발되었다. 제어기는 아나로그 PI제어기이고 플랜트의신호는 On-line으로 받지만 동조는 off-line에서 이루어진다. 또한 동조를 위한 특징량을 플랜트로 부터 얻을 수 있어야 한다. 동조 방법은 퍼지논리를 사용하였으며, 개발된 퍼지동조기는 공정의 현재신호와 과거의 상태를 보여주며 동조된 새로운 PI제어기의 이득값을 제시한다. 퍼지동조기는 현장에서 여러실험을 통하여 성능을 검증하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.220-227
• /
• 2000

The purpose of this study is to develop the non-gravity fluidized dryer. In this non-gravity fluidized dryer the fluidized zone is produced by two paddles in mixer, which maximizes the surface area of materials and then heated air through the guiding panels dehumidify them. This can conduct the drying process quickly and control moisture contents to lower limits. The ventilation system is closed loop system, which can be changeable to open system, and can be used as a multi-purposed dryer in which mixing, drying, granulating and cooling process is conducted. In order to develop non-gravity fluidized dryer, in the first the fundamental experiments performed to mixing accuracy and then the other parts of dryer and control system were examined to check whether they were designed properly and operated harmoniously with mixer. Also the preparatory experiments were fulfilled to examine the efficiency and reliability of dryer. Lastly, on the basis of preparatory experiments in case the initial moisture contents, desired moisture contents, heated air velocity and heating temperature were vary, performance test for the non-gravity fluidized dryer carried out.