• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.88-93
• /
• 2012

This paper describes the machinability of the sintered carbide and tool-die steel(STD-11) by electric discharge drilling with various tubular electrodes which have multi-holes. Various types of electrode which have different diameters and materials are used with the application of continuous direct current and axial electrode feed. Inner part of electrodes are inserted with smaller tubes or Y-channel or bar. In ED-Drilling, the dielectric flushed down the interior of the rotating tube electrode, in order to remove machining debris from the hole. As result of experiments, the bigger the diameter of the electrode is, the lower the material removal rate is. Machinability of copper electrode is higher than that of brass. In machining of sintered carbide, to use oil is better than distilled water as dielectric.

• Proceedings of the SAREK Conference
• /
• 2004.11a
• /
• pp.119-119
• /
• 2004

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.10
• /
• pp.710-718
• /
• 2010

A numerical study was performed to predict refrigerant charge amount in a mini-channel condenser for a R410A residential air-conditioning system. Multi-channel flat tubes with 12 mini-channels of 1.17 mm average hydraulic diameter for each tube were applied to the condenser. The condenser consisted of 3 passes, and the first, second, and third pass had 44, 19, and 11 tubes, respectively. Each pass was connected by a vertical header. In this study, the condenser was divided into 410 finite volumes, and analyzed by an $\varepsilon$-NTU method. With thermophysical properties and void fraction models for each volume element, the R410A amount distribution and a total charge amount in the condenser were calculated. The predicted total charge amount was compared with the experimentally measured charge amount under a standard ARI A condition. The developed model could predict the charge amount in the mini-channel condenser within prediction errors from -23.9% to -3.0%. Air velocity distribution at the condenser face was considered as non-uniform and uniform by the simulation model, and its results showed that the air velocity distribution could significantly influence the charge amount and vapor phase distribution in the condenser.

• Journal of the Korea Society of Computer and Information
• /
• v.23 no.9
• /
• pp.27-34
• /
• 2018

Personal media centered on blogs, Twitter, and Facebook has opened up a personal broadcasting area while meeting platforms such as YouTube and Africa TV. Due to the many advantages and disadvantages of personal broadcasting, a study on it was necessary and statistical survey was conducted. The study conducted opinion survey of 118 university students on personal broadcasting. As a result, we are getting news using smartphones and mainly watching videos through YouTube, and watching videos type in the order of games, music videos and sports. Satisfaction rate of video was 72.4%, 80.2% of survey did not use paid services, experiences about personal broadcasting was 96.6% and 90.5% of survey the prospect of person broadcasting of the opinion that "it will be expanded". The first thing we want to be improved in personal broadcasting is the prevention of abusive language and hate speech. Second, we were reluctant to sensational content. Third, the survey results are the improvement of excessive advertising.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.2
• /
• pp.10-17
• /
• 2009

Transillumination system used by radiation is widely applied to industrial imaging system. In this study, the linear detector array constructed with scintillator and pin diode, and a multi-channel data acquisition system was developed for precision inspection of end-milling. The detector module consists of $16-CdWO_4$crystal scintillator and photodiode array. The detector and data acquisition system was applied to precision inspection of end-mill and the images of the end-mill were successfully reconstructed. The total system can analyze the Detector Quantum Efficiency(DQE) of each system. The performance of developed photodiodes equipment was compared with each other for different crystal geometry and its characteristics. Finally fine details of the end-mill phantom were constructed for industrial application. The image acquired contains several objects on a real time data transfer and the linear X-ray scanning system can be applied to many fields of a industry.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.8
• /
• pp.1005-1012
• /
• 2001

When vortex tubes are applied to enhance the coefficient of performance of refrigeration system, the smaller one is preferable. However, the existing vortex generator with a nozzle hole diameter of 0.5mm was not suitable due to chocking of the nozzle hole. Therefore, experimental investigation was made to find an appropriate geometry of vortex generator, which could give a comparable effect of energy separation to commercial ones without chocking problem. The tested vortex generators were tangential and spiral types, which had single inducing channel with larger cross-sectional area than that of conventional multi-hole ones. The experimental result showed that the performance of the spiral type was better than that of the tangential one. As a small size of spiral one, the diameter of cold-end orifice is proposed to an half of tube diameter for the application to refrigeration system, while cold mass fraction ratio is 0.5∼0.6 for a desirable operation.

• Design & Manufacturing
• /
• v.17 no.4
• /
• pp.63-71
• /
• 2023

In order to increase the extrusion production speed of aluminum, extrusion die cooling technology using liquid nitrogen has recently attracted a lot of attention. Increasing the extrusion speed increases the temperature of the bearing area of extrusion dies and the extrusion profile, which may cause defects on the surface of extruded profile. Extrusion die cooling technology is to directly inject liquid nitrogen through a cooling channel formed between the die and the backer inside the die-set. The liquid nitrogen removes heat from the die-set, and gaseous nitrogen at the exit of the channel, covers the extrusion profile of an inert atmosphere reducing the oxidation and the profile temperature. The aim of this study is to evaluate the cooling capacity by applying die cooling to extrusion of Al-Mn-based aluminum alloy flat tubes, and to investigate the effects of die cooling on the change in extrusion characteristics of flat tubes. Cooling capacity was confirmed by observing the temperature change of the extrusion profile depending on whether or not die cooling is applied. To observe changes in material characteristics due to die cooling, surface observation is conducted and microstructure and precipitate analysis are performed by FE-SEM on the surface and longitudinal cross section of the extruded flat tubes.

• Journal of the Korean Society of Combustion
• /
• v.18 no.3
• /
• pp.24-30
• /
• 2013

Flame stabilization characteristics of premixed flames in an annular coaxial 5-tubes burner (AC5TB) were investigated experimentally. The AC5TB was made of five quartz tubes, and the flame stabilization conditions in that burner were investigated with the variation of equivalence ratio and the flow velocities. Flame behaviors inside of narrow annular tubes could be observed directly. Overall flame stabilization conditions were similar to that of the previous study, while the flame behaviors and structures were different mainly due to the controlled uniform distribution of the velocities in channels. Flame flashback conditions were thought to be governed by the competition between heat release rate, heat loss and heat recirculation in each channel. Stationary flames at a fixed location were compared in its velocity distribution and burned gas temperature across the channel. This AC5TB can be a basic configuration for the development of flame stabilization model of porous media combustors, and it will help understand about the real behavior of flames in meso-scale combustion spaces.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2006.05a
• /
• pp.399-402
• /
• 2006

한국 원자력 연구소는 PEFP(Proton Enginnering Frontier Poject)라고 하는 프로젝트를 수행 중이며, PEFP는 고에너지 양성자 가속기에 대한 프로젝트이다. 양성자 가속기에 대한 제어 시스템은 안정적인 운전 제어를 위해서 장치의 상태를 주기적으로 모니터링 할 뿐만 아니라 장치상태를 저장하여 일정시간 후에 확인이 요구되면 저장된 데이터를 이용하여 이전 정보를 추적할 수 있어야한다. 따라서 양성자 가속기 제어시스템에서는 실시간으로 들어오는 진공 데이터 정보를 저장 및 저장된 데이터를 열람이 가능한 저장 시스템으로 구성하였다. 저장된 데이터들은 RFQ(Radio Frequency Quadrupole) Cryopump, Turbo Pump, Press Gauge, Gate Valve, Compressor와 DTL(Drift Tube Linac) Multi-Gauge, Turbo Pump등의 진공도 및 제어변수 등이 있다. 이들 각각의 진공장치로부터 전달되는 진공 데이터들을 저장하기 위해 EPICS Extension toolset중에서 저장하는 기능을 가진 Channel Archiver를 양성자 가속기 제어 시스템에 추가하였다

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.35-37
• /
• 2002

Conceptual design of the next generation PET with both high sensitivity and high spatial resolution has been performed. A detector unit using a depth encoding scheme was designed and constructed for trial. The unit consists of four Gd$_2$SiO$\sub$5/:Ce crystal blocks in a 2x2x4 array coupled to a position-sensitive photomultiplier tube having metal channel dynodes and 4x4 multi-anodes. Our proposed detector is a very reliable and simple solution suitable for volume PET devices since the proposed depth encoding scheme does not need additional photo-detectors.