• Wind and Structures
• /
• 제32권3호
• /
• pp.267-281
• /
• 2021

Bending-twisting coupling induced in big composite wind turbine blades is one of the passive control mechanisms which is exploited to mitigate loads incurred due to deformation of the blades. In the present study, flutter characteristics of bend-twist coupled blades, designed for load alleviation in wind turbine systems, are investigated by time-domain analysis. For this purpose, a baseline full GFRP blade, a bend-twist coupled full GFRP blade, and a hybrid GFRP and CFRP bend-twist coupled blade is designed for load reduction purpose for a 5 MW wind turbine model that is set up in the wind turbine multi-body dynamic code PHATAS. For the study of flutter characteristics of the blades, an over-speed analysis of the wind turbine system is performed without using any blade control and applying slowly increasing wind velocity. A detailed procedure of obtaining the flutter wind and rotational speeds from the time responses of the rotational speed of the rotor, flapwise and torsional deformation of the blade tip, and angle of attack and lift coefficient of the tip section of the blade is explained. Results show that flutter wind and rotational speeds of bend-twist coupled blades are lower than the flutter wind and rotational speeds of the baseline blade mainly due to the kinematic coupling between the bending and torsional deformation in bend-twist coupled blades.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제17권2호
• /
• pp.353-368
• /
• 2023

The four wing unmanned aerial vehicle owns the characteristics of small size, light weight, convenient operation and well stability. But it is easily disturbed by external environmental factors during flight with these disadvantages of short endurance and poor attitude solving ability. For solving these problems, a microprocessor based on STM32 chip is designed and the overall development is completed by the resources such as built-in timer and multi-function mode general-purpose input/output provided by the master micro controller unit, together with radio receiver, attitude meter, barometer, electronic speed control and other devices. The unmanned aerial vehicle can be remotely controlled and send radio waves to its corresponding receiver, control the analog level change of its corresponding channel pins. The master control chip can analyze and process the data to send multiple sets pulse signals of pulse width modulation to each electronic speed control. Then the electronic speed control will transform different pulse signals into different sizes of current value to drive the motor located in each direction of the frame to generate different rotational speed and generate lift force. To control the body of the unmanned aerial vehicle, so as to achieve the operator's requirements for attitude control, the PID controller based on Kalman filter is used to achieve quick response time and control accuracy. Test results show that the design is feasible.

• 드라이브 ㆍ 컨트롤
• /
• 제17권1호
• /
• pp.37-43
• /
• 2020

An intelligent excavator can be divided into Machine Guidance (MG), semi-automatic, and unmanned by technology. The MG technology excavator is equipped with a tilt sensor on each link of the excavator and a GPS is installed on the excavator body to inform the user of the position of the excavator bucket end. Machine control (MC) technology that assists the user's work can be divided into semi-automatic and fully automatic technology. The semi-automatic MC equipment has already been commercialized by Komatsu and Caterpillar. The MC excavator is equipped with an electro-hydraulic system, sensors and controllers to control the excavator bucket end according to the user's needs. In this study, the semi-automated excavator modified based on manual excavator, is equipped with an electro-hydraulic system, a controller system, multi-sensors and a control algorithm is developed to assist in excavation work such as leveling and grading. By applying the developed technology, it was possible to confirm productivity improvement compared to manual digging and leveling work. In the future, further research to improve the accuracy of the hydraulic precision control and collaborative work with heterogeneous construction equipment such as dump truck and automated collaboration tasks technology could be developed.

• 대한의용생체공학회:의공학회지
• /
• 제28권4호
• /
• pp.494-502
• /
• 2007

Ubiquitous location based services (u-LBS) will be interested to an important services. They can easily recognize object position at anytime, anywhere. At present, many researchers are making a study of the position recognition and tracking. This paper consists of postion recognition and user identification system. The position recognition is based on location under services (LBS) using a signal strength map, a database is previously made use of empirical measured received signal strength indicator (RSSI). The user identification system automatically controls instruments which is located in home. Moreover users are able to measures body signal freely. We implemented the multi-hop routing method using the Star-Mesh networks. Also, we use the sensor devices which are satisfied with the IEEE 802.15.4 specification. The used devices are the Nano-24 modules in Octacomm Co. Ltd. A RSSI is very important factor in position recognition analysis. It makes use of the way that decides position recognition and user identification in narrow indoor space. In experiments, we can analyze properties of the RSSI, draw the parameter about position recognition. The experimental result is that RSSI value is attenuated according to increasing distances. It also derives property of the radio frequency (RF) signal. Moreover, we express the monitoring program using the Microsoft C#. Finally, the proposed methods are expected to protect a sudden death and an accident in home.

• Ocean and Polar Research
• /
• 제37권2호
• /
• pp.119-125
• /
• 2015

This paper focuses on the efficient arrangement plan of buoyancy modules, which plan is used to secure the safe operation and structural stability of a marine riser. The marine riser is connected between a vessel and seabed devices. The movement of the vessel and the seabed devices are affected by the motion of the riser. The riser of a deep-seabed integrated mining system exerts a strong influence on the healthy transfer of minerals. So, buoyancy modules must be equipped to compensate for the problem which is the structure stability and the dynamic motion. Installation locations and quantities of the buoyancy modules are determined by real sea experiments. But this is not easy to do because in real sea experimental conditions the cost is expensive as well as being, time-consuming and dangerous. Therefore, the locations and quantities should be determined by numerical simulation. This method is called simulation-based design. The dynamic analysis models of the riser and the buoyancy modules are built into the commercial software of DAFUL.

• 한국기계가공학회지
• /
• 제17권1호
• /
• pp.130-137
• /
• 2018

In long freight trains, there is a brake time delay in the neighboring freight cars that causes damage and fractures of couplers, especially the knuckle of them. If there is a problem for couplers in the cars, this could cause a derailment and lead to damage of human life and property damage. In this study, maximum forces on the couplers are studied when a long freight car brakes, with brake delay time and coupler gap. We have made a dynamic model of 50 freight cars and couplers, applying contact between couplers and a characteristic curve for expressing force and displacement of buffers with SIMPACK, a multi-body dynamics program. We use EN 14531-2 from the British Standards Institution, a standard of freight car brakes for the verification of the dynamic model. We also use a simplified method to analyze the dynamic model of 50 freight cars. With changing coupler gap and brake delay time, we do comparative analysis with AAR M-201 from the Association of American Railroads, a standard of AAR couplers. From this result, we find that the standard on fatigue limit is satisfied, such that the brake delay time is within 0.06 second if the coupler gap of the AAR coupler is within 20 millimeters.

• 대기
• /
• 제20권2호
• /
• pp.131-151
• /
• 2010

This study establishes a conceptual model to analyze heavy rainfall events in Korea using multi-functional transport satellite-1R satellite images. Three heavy rainfall episodes in two major synoptic types, such as synoptic low (SL) type and synoptic flow convergence (SC) type, are analyzed through a conceptual model procedure which proceeds on two steps: 1) conveyer belt model analysis to detect convective area, and 2) cloud top temperature analysis from black body temperature (TBB) data to distinguish convective cloud from stratiform cloud, and eventually estimate heavy rainfall area and intensity. Major synoptic patterns causing heavy rainfall are Changma, synoptic low approach, upper level low in the SL type, and upper level low, indirect effect of typhoon, convergence of tropical air in the SC type. The relationship between rainfall and TBBs in overall well resolved areas of heavy rainfall. The SC type tended to underestimate the intensity of heavy rainfall, but the analysis with the use of water vapor channel has improved the performance. The conceptual model improved a concrete utilization of images and data of satellite, as summarizing characteristics of major synoptic type causing heavy rainfall and composing an algorism to assess the area and intensity of heavy rainfall. The further assessment with various cases is required for the operational use.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.91-98
• /
• 2017

This study was conducted to optimize the spring constant and the damping coefficient, which are design parameters of the tractor cabin suspension system, to minimize the ride vibration. A 3D tractor MBD (multi-body dynamics) model with a cabin suspension system was developed using a dynamic analysis program (Recurdyn). Using the developed model and optimization algorithm, the spring constant and the damping coefficient, which are the design parameters of the cabin suspension for the tractor, was were optimized so thatto minimize the maximum overshoot for the vertical displacement of the cabin was minimized. The percent maximum overshoot of the tractor cabin was simulated for the 13 initial models, which were obtained using the ISCD-II method, and for the 3 additional SAO models presented in the optimization algorithm software. The model that represents with the smallest percent maximum overshoot among the 16 models was selected as the optimized model. The percent maximum overshoot of the optimized model was about approximately 5% lower than that of the existing model.

• Korean Journal of Geomatics
• /
• 제2권1호
• /
• pp.47-55
• /
• 2002

Remote sensing is the science and art of obtaining information about an object, area or phenomenon through the analysis of data acquired by a device that is not in contact with the object, area, or phenomenon under investigation./sup 1)/ EOC (Electro -Optical Camera) sensor loaded on the KOMPSAT-1 (Korea Multi- Purpose Satellite-1) performs the earth remote sensing operation. EOC can get high-resolution images of ground distance 6.6m during photographing; it is possible to get a tilt image by tilting satellite body up to 45 degrees at maximum. Accordingly, the device developed in this study enables to obtain images by photographing one pair of tilt image for the same point from two different planes. KOMPSAT-1 aims to obtain a Korean map with a scale of 1:25,000 with high resolution. The KOMPSAT-1 developed automated feature extraction system based on stereo satellite image. It overcomes the limitations of sensor and difficulties associated with preprocessing quite effectively. In case of using 6, 7 and 9 ground control points, which are evenly spread in image, with 95% of reliability for horizontal and vertical position, 3-dimensional positioning was available with accuracy of 6.0752m and 9.8274m. Therefore, less than l0m of design accuracy in KOMPSAT-1 was achieved. Also the ground position error of ortho-image, with reliability of 95%, is 17.568m. And elevation error showing 36.82m was enhanced. The reason why elevation accuracy was not good compared with the positioning accuracy used stereo image was analyzed as a problem of image matching system. Ortho-image system is advantageous if accurate altitude and production of digital elevation model are desired. The Korean map drawn on a scale of 1: 25,000 by using the new technique of KOMPSAT-1 EOC image adopted in the present study produces accurate result compared to existing mapping techniques involving high costs with less efficiency.

• 한국산학기술학회논문지
• /
• 제20권4호
• /
• pp.632-638
• /
• 2019

본 논문은 도로와 철도를 포함하는 인터모달 자동화물운송시스템을 위한 화물열차 대차 구조를 소개하고, 레일에 대한 반력 해석 결과를 논한다. 새로운 운송시스템은 시간과 비용을 획기적으로 절약할 수 있는 회전 정렬형 철도차량 방식을 기반으로 한다. 개념 설계 단계에서 고려해야하는 중요한 문제 중의 하나는 궤도 및 대차의 특징적인 형태에서 발생하는 레일에 가해지는 횡력이다. 특히 주행 궤도에서 플랫폼 구간으로 바뀌는 천이구간에서 큰 횡력이 발생하는데, 해석 결과를 바탕으로 향후 시스템 설계 시 참조할 수 있는 설계 가이드를 제공하고자 한다. 해석 결과, 제안하는 구조가 궤도 안정성 및 주행 안정성 면에서 문제가 없어 실제 시스템에 적용할 수 있는 구조이며, 주행 구간에서 플랫폼 구간으로 궤도가 변하는 곳에서 궤도의 선형을 설계할 시, 곡률 반경과 플랫폼 궤도 사이 거리가 중요한 변수임을 밝혀졌다.