• Tribology and Lubricants
• /
• 제21권6호
• /
• pp.263-267
• /
• 2005

The tribological performance of multi-walled carbon nanotubes (MWNT) in mineral oils is investigated at ambient temperature. The frictional forces, wear amounts and cycles to scuffing of the oils with nanotubes and without those were measured using the ball-on-disk tester. It was found that there were little differences in the frictional forces and wear amounts of two oils. However, the scuffing times of oils with nanotubes were much longer than those of oils without nanotubes in sliding tests. The nanotubes were very effective on maintaining the oil gap and protecting the surfaces in boundary lubricated sliding.

• 한국가스학회지
• /
• 제10권2호
• /
• pp.27-32
• /
• 2006

본 논문은 다수의 볼과 접촉하는 두개의 실린더 사이에서 발생하는 접촉응력과 마찰력을 유한요소법으로 해석하였다. LPG 충전기는 구름마찰 운동을 위해 다수의 볼이 평행한 두개의 실린더와 경사진 두개의 실린더 레이스에서 구름마찰 운동을 한다. FEM 해석결과에 의하면, SiC 볼과 SUS 304 볼은 주어진 수직하중, 즉 압축력에 대하여 높은 접촉응력과 마찰력 손실을 보여주고 있다. 반면에 PEEK 볼을 두개의 실린더에 대하여 구름마찰 운동을 유지하면, 대단히 낮은 접촉응력과 마찰력 손실을 나타내는 것으로 보아 폴리머 소재의 사용은 저마찰 접촉특성을 잘 구현하고 있다할 수 있다. 여기에 두개의 실린더가 평행하게 구름마찰 접촉운동을 하느냐, 또는 경사진 상태에서 구름마찰 운동을 하느냐에 따라 접촉거동 특성이 크게 달라지므로 특히 두개 실린더 사이의 상대적 경사도는 극도로 억제되어야 우수한 설계가 된다.

• Structural Engineering and Mechanics
• /
• 제83권5호
• /
• pp.655-669
• /
• 2022

Passive vibration control devices like tuned liquid column dampers (TLCD) not only significantly reduce buildings' vibrations but also can serve as a water storage facility. The recently introduced modified form of TLCD known as tuned liquid column ball damper (TLCBD) suppressed external vibration efficiently compared to traditional TLCD. For excellent performance, the mass ratio of TLCBD should be in the range of 5% to 7%, which does not include the mass of the ball. This additional mass of the ball increases the overall structure mass. Therefore, in this paper, an effort is made to reduce the mass of TLCBD. For this purpose, a new modified version of TLCBD known as tuned liquid column hollow ball damper (TLCHBD) is proposed. The existing mathematical modeling of TLCBD is used for this new damper by updating the numerical values of the mass and mass moment of the ball. Analytically the optimal design parameters are obtained. Numerically the TLCHBD is investigated with a single degree of freedom structure under harmonic and seismic loadings. It is found that TLCHBD performance is similar to TLCBD in both loadings' cases. To validate the numerical results, an experimental study is conducted. The mass of the ball of TLCHBD is reduced by 50% compared to the ball of TLCBD. Both the arrangements are studied with a multi-degree of freedom structure under harmonic and seismic loadings using a shake table. The results of the experimental study confirm the numerical findings. It is found that the performance behavior of both the dampers is almost similar under harmonic and seismic loadings. In short, the TLCHBD is lighter in weight than TLCBD but has a similar vibration suppression ability.

• 대한기계학회논문집A
• /
• 제32권8호
• /
• pp.642-653
• /
• 2008

In this paper, we propose a 3-D finite element (FE) analysis model with combined physical behavior and kinematical impact factors for evaluation of residual stress in multi-impact shot peening. The FE model considers both physical behavior of material and characteristics of kinematical impact. The physical parameters include elastic-plastic FE modeling of shot ball, material damping coefficient, dynamic friction coefficient. The kinematical parameters include impact velocity and diameter of shot ball. Multi-impact FE model consists of 3-D symmetry-cell. We can describe a certain repeated area of peened specimen under equibiaxial residual stress by the cell. With the cell model, we investigate the FE peening coverage, dependency on the impact sequence, effect of repeated cycle. The proposed FE model provides converged and unique solution of surface stress, maximum compressive residual stress and deformation depth at four impact positions. Further, in contrast to the rigid and elastic shots, plastically deformable shot produces residual stresses closer to experimental solutions by X-ray diffraction. Consequently, it is confirmed that the FE model with peening factors and plastic shot is valid for multi-shot peening analyses.

• 소성∙가공
• /
• 제23권4호
• /
• pp.211-220
• /
• 2014

The outer race of a constant velocity (CV) joint having six inner ball grooves has traditionally been manufactured by multi-stage warm forging, which includes forward extrusion, upsetting, backward extrusions, necking, ironing and sizing, and machining. In the current study, a multi-stage cold forging process is examined and an assessment for replacing and modifying the conventional multi-stage warm forging is made. The proposed procedure is simplified to the backward extrusion of the conventional process, and the sizing and necking are combined into a single sizing-necking step. Thus, the forging surface of the six ball grooves can be obtained without additional machining. To verify the suitability of the proposed process, a 3-dimensional numerical simulation on each operation was performed. The forging loads were also predicted. In addition, a structural integrity evaluation for the tools was carried out. Based on the results, it is shown that the dimensional requirements of the outer race can be well met.

• Advances in materials Research
• /
• 제6권3호
• /
• pp.245-255
• /
• 2017

High energy ball milling is employed to produce iron matrix- multiwall carbon nanotube (MWCNT) reinforced composite. The damage caused to MWCNT due to harsh ball milling condition and its influence on interfacial bonding is studied. Different amount of MWCNT is used to find the optimal percentage of MWCNT for avoidance of the formation of chemical reaction product at the matrix - reinforcement interface. Effect of process control agent is assessed by the use of different materials for the purpose. It is observed that ethanol as a process control agent (PCA) causes degradation of MWCNT reinforcements after milling for two hours whereas solid stearic acid used as process control agent, allows satisfactory conservation of MWCNT structure. It is further noted that at a high MWCNT content (~ 2wt.%), high energy ball milling leads to reaction of iron and carbon and forms iron carbide (cementite) at the iron-MWCNT interface. At low percentage of MWCNT, dissolution of carbon in iron takes place and the amount of reinforcement in iron matrix composite becomes negligibly small. However, under the present ball milling condition (ball to metal ratio~ 6:1 and 200 rpm vial speed) iron-1wt.% MWCNT composite of good interfacial bonding can retain the tubular structure of reinforcing MWCNT.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.27.2-27.2
• /
• 2009

Grinding characteristics for aluminium and carbon nanotubes (CNTs) powder during traditional and planetary ball milling investigated from the viewpoint of particle behaviour with the aimat developing CNT-dispersed samples ground based on powder metallurgy routes.In this work, a comparison between the pure aluminium and CNT input aluminium grinding was carried out to determine grinding time effect on size reduction.We observed that the use of the curly small-diameter multi-walled carbon nanotubes (MWCNTs) attributed to the beneficial role of the MWCNTs as grinding aids. It is suggested that careful choices of the sizes of CNTs and Al powders would allow fine-grinding of composite particles with uniformly distributed CNT reinforcements thereby ensuring improved properties of the final composites produced by low-temperature compacting.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.401-402
• /
• 2012

• 한국정밀공학회지
• /
• 제28권8호
• /
• pp.904-914
• /
• 2011

The volumetric errors of CNC machining centers are determined by 21 errors, including 3 linear errors, 6 straightness errors, 3 perpendicular errors, 9 angular errors and non-rigid body errors of the machine tool. It is very time consuming and hard to measure all of these errors in which laser interferometer and other parts are used directly. Hence, as many as 21 separate setups and measurements are needed for the linear, straightness, angular and perpendicular errors. In case of the 5-axis machining centers, two more rotary tables are used. It can make 35 error sources of the movement. Therefore, the measured errors of multi movements of the 5-axis tables are very complicated, even if the relative measured errors are measured. This paper describes the methods, those analyze the error sources of the machining centers. Those are based on shifted diagonal measurements method (SDM), R-test and Double ball bar. In case, the angular errors of machine are small enough comparing with others, twelve errors including three linear position errors, six straightness errors and three perpendicular errors can be calculated by using SDM. To confirm the proposed method, SDM was applied to measuring 3 axes of machine tools and compared with directly measurement of each errors. In addition, the methods for measuring relative errors of multi-axis analysis methods using R-test and Double Ball Bar are introduced in this paper.

• 한국육종학회지
• /
• 제40권4호
• /
• pp.490-494
• /
• 2008

절화용 국화 'Eye Ball' 품종은 경남농업기술원 화훼연구소에서 육성한 백색의 스프레이 신품종으로 적색 홑꽃인 'Dublin'을 모본, 백색 홑꽃인 'Yen'을 부본으로 '02년 10월에 인공교배를 실시하였다. 줄기가 강건하고 화색이 선명하며 조기 개화하는 우수 6개체(DY02-73, 97, 142, 247, 314, 426)를 1차로 선발하였다. 2004년부터 2006년까지 3회에 걸쳐 특성을 검정하고, 품평회와 시장출하를 통해 기호성이 좋고, 화색 및 화형 등 품질이 우수하다고 판단된 DY02 -314(경남CS-5호)를 2007년 농작물 직무육성신품종선정위원회의 심의를 거쳐 'Eye Ball'로 명명하였다. 'Eye Ball' 품종은 줄기가 굵고 화색이 선명한 백색 화색의 홑꽃으로서 개화소요기간이 7주 정도이며, 착화수도 18.2개이다. 꽃 크기는 3.3 cm 정도이며, 초장이 84.0 cm인 산티니계의 스프레이국화로서 평균 절화수명이 21.3일로 긴 편이다.