• Bulletin of the Korean Chemical Society
• /
• 제31권8호
• /
• pp.2279-2282
• /
• 2010

In this work, the electrical and thermal properties of polyimide/multi-walled carbon nanotube (MWNT) nanocomposites were investigated. The polyimide/MWNT nanocomposites contained from 0 to 2.0 wt % of MWNT. The electrical properties of the polyimide films were characterized by a specific resistance measurement. The thermal properties were evaluated using thermogravimetric analysis (TGA) and a differential scanning calorimeter (DSC). It was found that the thermal properties of the polyimide nanocomposites increased with increasing MWNT content and specific resistance as well. This result indicated that the crosslinking of polyimide/MWNT nanocomposites was enhanced by good distribution of the MWNT in the polyimide resins, resulting in the increase of the electrical and thermal properties of the nanocomposites.

• 한국전기전자재료학회논문지
• /
• 제23권4호
• /
• pp.338-342
• /
• 2010

Carbon nanotubes (CNTs) have excellent electrical, chemical stability, mechanical and thermal properties. The MWCNT films were investigated as a transparent electrode for the solar cell, OLED, and field-emission display. MWCNT films were fabricated by air spray method, whose process is quite low-costed, using the multi-walled CNTs solution on glass substrates. Moreover, the most stable film was fabricated when the spraying time was 60 sec. The film that was sprayed with the MWCNT dispersion for 60 sec, has 300nm thick. And its electric resistivity, transmittance rate, mobility and carrier concentration are $6{\times}10^{-2}{\Omega}{\cdot}cm$, 50% at ${\lambda}=550mm$, $4.3{\times}10^{-2}cm^2/V{\cdot}s$ and $2.1{\times}10^{21}cm^{-3}$, respectively. Also, absorption energy of MWCNT films show from 3.9 eV to 4.6 eV. Furthermore, we can use MWCNT films fabricated by the spray method for the transparent electrode.

• Journal of Electrochemical Science and Technology
• /
• 제11권4호
• /
• pp.399-405
• /
• 2020

Hollow copper oxide/multi-walled carbon nanotubes (CuO/MWCNT) composites were fabricated via an optimized infiltration-reduction-oxidation method, which is more facile and easy to control. The crystalline structure and morphology were characterized by X-ray diffraction (XRD), and transmission electron microscopy (TEM). The as-prepared CuO/MWCNT composites deliver an initial capacity of 612.3 mAh·g^-1 and with 80% capacity retention (488.2 mAh·g^-1) after 100 cycles at a current rate of 0.2 A·g^-1. The enhanced electrochemical performance is ascribed to the better electrical conductivity of MWCNT, the hollow structure of CuO particles, and the flexible structure of the CuO/MWCNT composites.

• 산업기술연구
• /
• 제34권
• /
• pp.39-43
• /
• 2014

This paper represents a highly porous MWCNT film electrode with interconnected open pores and demonstrated the possibility of using an MWCNT network film as the top electrode for polyimide capacitive humidity sensors. Polyimide humidity sensors with MWCNT electrodes exhibited about 6 times faster response than equivalent Cr electrode sensors. This result may be due to their percolated pore structures, which make water molecules accessible to all polyimide surfaces. The much faster response times of MWCNT electrode sensors is attributed to the percolated pore network, which allows more water molecules to be accessible to polyimide surfaces.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2010년도 춘계학술발표논문집 2부
• /
• pp.1127-1130
• /
• 2010

본 연구에서는 CNT의 분산성을 개선하고자 다중벽 탄소나노튜브(multi-walled carbon nanotube, MWNT)에 butyllithium solution 및 hexyllithium solution을 이용하여 표면을 화학적으로 개질하였다. 개질된 MWNT는 적외선 분광 분석 및 Raman spectrophotometer를 이용하여 MWNT에 작용기가 도입되었는지를 확인하였다. 또한, 열중량분석기(Thermogravimetric analysis, TGA)를 이용하여 작용기가 도입된 MWNT의 열적 성질을 측정하였으며, MWNT 및 개질된 MWNT를 다양한 용매에 따른 분산성을 확인하였다.

• Steel and Composite Structures
• /
• 제17권6호
• /
• pp.825-834
• /
• 2014

This manuscript presents an experimental investigation on the effect of Multi-walled carbon nanotubes (MWCNTs) addition on the tensile, flexural and impact properties of woven Kevlar fabric reinforced epoxy composites. MWCNTs were dispersed in the epoxy resin by sonication technique and the samples were fabricated by hand layup laminating procedure. Scanning electron microscopy (SEM) was used to characterize the microstructure of produced samples. The effects of adding small amounts (${\leq}1%$) of MWCNT on the tensile, flexural and impact (Izod) behaviors of laminated composites were analyzed. Results revealed that MWCNTs enhanced the Young's modulus up to 20%, bending modulus up to 40%, and impact strength up to 45% in comparison with woven Kevlar fabric/epoxy composites. It was found that the maximum improvements in mechanical properties were happened for 0.5 wt.% MWCNT.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.418-419
• /
• 2007

플라즈마 열화학기상 증착법으로 Fe-Ni-Co 3원계 측매합금을 이용하여 $442^{\circ}C$의 저온에서 다중벽 탄소나노튜브를 합성하였다. 수소의 유량이 일정할 때 아세틸렌의 유량이 감소함에 따라 성장속도가 증가하였다. 합성된 탄소나노튜브는 약 8.4 nm의 직경과 $5.5\;{\mu}m$의 길이를 보였으며, 기판에 대해 수직으로 성장되었다. 4인치 웨이퍼 위에서도 전면적에서 균일한 성장을 보였다.

• Journal of Ceramic Processing Research
• /
• 제20권5호
• /
• pp.464-469
• /
• 2019

In this study, the electrical conductivity of multi-walled carbon nanotubes (MWCNTs) and polyethylene synthesized by an extrusion process was evaluated. The MWCNTs used exhibited differences in their dispersion characteristics depending on the type of catalyst or synthesis gas used. Thus, the choice of catalyst or synthesis gas significantly affect the physicochemical state of the final MWCNTs and MWCNT-based composites. In this investigation, the characteristics of MWCNTs were analyzed in four cases by introducing ethylene and propylene gas to each catalyst synthesized using deposition precipitation and spray drying methods. The MWCNT-based composites synthesized using the catalyst prepared by deposition precipitation and the ethylene synthesis gas showed the best electrical conductivity. In principle, the morphologies of the MWCNTs indicate that the smaller the aggregate size and bundle thickness, the better the electrical conductivity of the MWCNT composites. This implies that the network is well-formed.

• Carbon letters
• /
• 제15권2호
• /
• pp.117-124
• /
• 2014

Conductive polymer composites (CPCs) consist of a polymeric matrix and a conductive filler, for example, carbon black, carbon fibers, graphite or carbon nanotubes (CNTs). The critical amount of the electrically conductive filler necessary to build up a continuous conductive network, and accordingly, to make the material conductive; is referred to as the percolation threshold. From technical and economical viewpoints, it is desirable to decrease the conductive-filler percolation-threshold as much as possible. In this study, we investigated the effect of polymer/conductive-filler interactions, as well as the processing and morphological development of low-percolation-threshold (${\Phi}c$) conductive-polymer composites. The aim of the study was to produce conductive composites containing less multi-walled CNTs (MWCNTs) than required for pure polypropylene (PP) through two approaches: one using various mixing methods and the other using immiscible polymer blends. Variants of the conductive PP composite filled with MWCNT was prepared by dry mixing, melt mixing, mechanofusion, and compression molding. The percolation threshold (${\Phi}c$) of the MWCNT-PP composites was most successfully lowered using the mechanofusion process than with any other mixing method (2-5 wt%). The mechanofusion process was found to enhance formation of a percolation network structure, and to ensure a more uniform state of dispersion in the CPCs. The immiscible-polymer blends were prepared by melt mixing (internal mixer) poly(vinylidene fluoride) (PVDF, PP/PVDF, volume ratio 1:1) filled with MWCNT.

• Carbon letters
• /
• 제15권4호
• /
• pp.255-261
• /
• 2014

Multi-walled carbon nanotube reinforced epoxy composites were fabricated using shear mixing and sonication. The mechanical, viscoelastic, thermal, and electrical properties of the fabricated specimens were measured and evaluated. From the images and the results of the measurements of tensile strengths, the specimens having 0.6 wt% nanotube content showed better dispersion and higher strength than those of the other specimens. The Young's moduli of the specimens increased as the nanotube filler content was increased in the matrix. As the concentrations of nanotubes filler were increased in the composite specimens, their storage and loss moduli also tended to increase. The specimen having a nanotube filler content of 0.6 wt% showed higher thermal conductivity than that of the other specimens. On the other hand, in the measurement of thermal expansion, specimens having 0.4 and 0.6 wt% filler contents showed a lower value than that of the other specimens. The electrical conductivities also increased with increasing content of nanotube filler. Based on the measured and evaluated properties of the composites, it is believed that the simple and efficient fabrication process used in this study was sufficient to obtain improved properties in the specimens.