• The KIPS Transactions:PartA
• /
• v.18A no.1
• /
• pp.19-24
• /
• 2011

As era of multi-core processors has arrived, transactional memory has been considered as an effective method to achieve easy and fast multi-threaded programming. Various hardware transactional memory systems such as UTM, VTM, FastTM, LogTM, and LogTM-SE, have been introduced in order to implement high-performance multi-core processors. Especially, LogTM-SE has provided study performance with an efficient memory management policy and a practical thread scheduling method through conflict detection based on signatures. However, increasing number of cores on a processor imposes the hardware complexity for signature processing. This causes overall performance degradation due to the heavy workload on signature comparison. In this paper, we propose a new architecture of multiple signature comparison to improve conflict detection of signature based transactional memory systems.

• Journal of Korea Multimedia Society
• /
• v.12 no.6
• /
• pp.824-832
• /
• 2009

Multi-radio multi-channel Wireless Mesh Network requires an effective management policy to control the assignment of channels to each radio. We concentrated our investigation on modeling method and solution to find a dynamic channel assignment scheme that is adapted to change of network traffic. Multi-path routing scheme was chosen to overwhelm the unreliability of wireless link. For a particular traffic state, our optimization model found a specific traffic distribution over multi-path and a channel assignment scheme that maximizes the overall network throughput. We developed a simple heuristic method for channel assignment by gradually removing clique load to obtain higher throughput. We also presented numerical examples and discussion of our models in comparison with existing research.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1173-1182
• /
• 1998

A throughflow analysis program for axial flow turbines is constructed, which can handle not only the two-dimensional multi-streamline (streamline curvature) method but also the one-dimensional mean line method. Calculations are performed for single stage and multi-stage axial flowturbines. For a wide operating range, the performance and flow field calculated by the present streamline curvature method are close enough to the test data. It is also revealed for the single stage turbine that the present analysis leads to far better correspondence with the experiment than other researchers" throughflow analyses. A special focus is put on the comparison of the results between the streamline curvature analysis and the mean line analysis. It is found that the mean line analysis can not predict the performance for highly off-designed conditions as accurately as the streamline curvature method, which shows the importance of considering the spanwise variation of loss and flow.

• The Journal of Korea Robotics Society
• /
• v.12 no.2
• /
• pp.161-172
• /
• 2017

Foot mechanisms play the role of interface between the main body of robotic systems and the ground. Biomimetic design of the foot mechanism is proposed in the paper. Specifically, multi-chained and multiple contact characteristics of general foot mechanisms are analyzed and their advantages are highlighted in terms of impulse. Using Newton-Euler based closed-form external and internal impulse models, characteristics of multiple contact cases are investigated through landing simulation of an articulated leg model with three kinds of foot. It is shown that in comparison to single chain and less articulated linkage system, multi-chain and articulated linkage system has superior characteristic in terms of impulse absorption as well as stability after collision. The effectiveness of the simulation result is verified through comparison to the simulation result of a commercialized software.

• Journal of computational fluids engineering
• /
• v.18 no.2
• /
• pp.93-98
• /
• 2013

In this paper, we reported the verification of numerical simulation approach for sedimentation of the multi-size particles in a container. The comparison between experimentally measured values and numerically evaluated values on settle down process of fully mixed mixture is carried out. In an attempt to represent the natural particle size distribution, various diameters of single particles are simulated and the results are compared with the outcome of the multi-size computation. When the empirical formula for mean particle size estimation is adopted to define the sediment diameter, computation and comparison are conducted.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.1058-1066
• /
• 2004

This paper proposes the acquisition system using the multiple antennas in DS-CDMA system. The conventional acquisition schemes using multiple antennas are the methods to utilize the multi-antenna combining and the fixed multi-beam forming of a serial acquisition. Then, this paper proposes the hybrid acquisition scheme using the fixed multi-beam forming. The numerical results show the performance comparison of two acquisition schemes in terms of the acquisition time ill the multipath Rayleigh fading channel.

• Journal of Aerospace System Engineering
• /
• v.15 no.6
• /
• pp.59-65
• /
• 2021

In this paper, the transmission characteristics of the multi-layered composite material with wire mesh and honeycomb core for aircraft applications have been analyzed with the proposed method. The proposed method converts the conductive wire mesh into effective layer, while for the dielectric honeycomb core, effective permittivity has been derived based on volume fraction with the proposed method. The proposed method has been verified through comparison with full-wave simulation and revealed excellent. In addition, the calculation time of the proposed method is a few order of magnitude faster in comparison with the full-wave simulation.

• Journal of Advanced Information Technology and Convergence
• /
• v.9 no.1
• /
• pp.11-24
• /
• 2019

This paper investigates the performance comparison of a Terahertz (THz) communications for a single-carrier and a multi-carrier single antenna point-to-point communication system. The multi-carrier system and single carrier system consider the orthogonal frequency division multiplexing (OFDM) and the minimum mean square error linear equalizer (MMSE-LE), respectively. We compare the frame-error-rate (FER) and throughput performance of both the systems for a THz communication environment with the carrier frequency of 300GHz and the tapped delay line (TDL) channel models described in 3GPP. It is observed from the simulation results that the OFDM systems outperform the MMSE-LE for various configurations.

• The KIPS Transactions:PartA
• /
• v.10A no.4
• /
• pp.357-368
• /
• 2003

Evaluation of shape similarity for 3D models is essential in many areas - medicine, mechanical engineering, molecular biology, etc. Moreover, as 3D models are commonly used on the Web, many researches have been made on the classification and retrieval of 3D models. In this paper, we describe methods for 3D shape representation and major concepts of similarity evaluation, and analyze the key features of recent researches for shape comparison after classifying them into four categories including multi-resolution, topology, 2D image, and statistics based methods. In addition, we evaluated the performance of the reviewed methods by the selected criteria such as uniqueness, robustness, invariance, multi-resolution, efficiency, and comparison scope. Multi-resolution based methods have resulted in decreased computation time for comparison and increased preprocessing time. The methods using geometric and topological information were able to compare more various types of models and were robust to partial shape comparison. 2D image based methods incurred overheads in time and space complexity. Statistics based methods allowed for shape comparison without pose-normalization and showed robustness against affine transformations and noise.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.4
• /
• pp.163-168
• /
• 2002

This paper presents the comparison results of control algorithm for the simultaneous control of a multi output converter system that controls, simultaneously and independently, the separate Buck converter and Boost converter with the different specification by one DSP digital controller. As two separate converters are regulated by only one DSP, it is possible to achieve the simple digital control circuit for regulating the multi output DC-DC converter. By setting the software switch state, PI and Fuzzy controller can be applied as a controller for each converter without any change of hardware. Also, it is included the control characteristics comparison between PI and Fuzzy controller. The control characteristics of each PWM DC-DC converter is validated by experimental results.