• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.177-177
• /
• 2010

고효율 비정질 실리콘 박막 태양전지 제작을 위해서는 광파장대에서 optical confinement 능력을 최대화할 수 있는 기술이 필수적이다. 효율적인 photon trapping을 위해서는 back reflector를 사용하거나 전면전극인 투명전도성막의 표면에 요철을 형성하여 포획된 태양광의 내부 반사를 증가시키거나 전면 투명전극에서 반사를 감소시켜 태양광의 travel length를 증가시키는 방법이 일반적이며, 이를 통해 흡수층의 효율을 최대화할 수 있다. 이 중 전면전극으로 사용되는 투명전도성막은 불소가 도핑된 tin-oxide가 주로 사용되었으나, 최근 들어 Al이 도핑된 산화아연막을 이용한 비정질 실리콘 박막 태양전지 개발에 대한 연구도 활발히 진행되고 있다. 투명전극 증착후 표면의 유효면적을 증가시키기 위해 염산 용액을 이용하여 표면 텍스쳐링을 수행한다. 그후 흡수층인 p-i-n 층을 플라즈마 화학기상증착법을 이용하여 형성하는 것이 일반적이다. 이때 표면처리 된 투명전극은 수소플라즈마에 대해 특성이 변하지 않아야 고효율 비정질 실리콘 박막 태양전지 제조에 적용될 수 있다. 본 연구에서는 표면처리 된 AZO 투명전극의 수소플라즈마에 의한 특성 변화에 대해 고찰하였다. 먼저 AZO 투명전극은 스퍼터링 공정을 적용하여 $1\;{\mu}m$두께로 증착하였고, 0.5 wt%의 HCl 용액을 이용하여 습식 식각을 수행하였다. 수소플라즈마 처리 조건은 $H_2$ flow rate 30 sccm, working pressure 20 mtorr, RF power 300 W, Temp $60^{\circ}C$ 이며 3분간 진행하였다. 표면형상은 수소플라즈마 전 후에는 큰 차이를 보이지 않았으며 AZO의 grain size는 각각 220 nm, 210 nm로 관찰되었다. 투명전극의 가장 중요한 특성인 가시광선 영역에서의 투과도는 수소플라즈마 처리전에는 90 % 이상의 투과도를 보였으나, 수소플라즈마 처리 후에는 85 %로 약간 저하된 특성을 보였다. 그러나 이는 박막 태양전지용 전면전극으로 사용하기 위한 투과도인 80 % 이상을 만족하는 결과로, 비정질 박막 실리콘 태양전지 제작에 사용될 수 있다. 또 하나의 중요한 특성인 Haze factor 역시 수소플라즈마 처리 전 후 모두 10 이상의 값을 나타냈다. 하지만 고효율 실리콘 박막 태양전지에 적용하기 위해서는 Haze factor를 증가시키는 공정 개발에 대한 추가 연구가 필요하다.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.492-499
• /
• 2000

Co-Ni-Fe-N thin films were fabricated by a N$\sub$2/ reactive rf magnetron sputtering method. The nitrogen partial pressure (P$\sub$N2/) was varied in the range of 0∼10%. As P$\sub$N2/ increases in this range, the saturation magnetization (B$\sub$s/) linearly decreases from 19.8 kG to 14 kG and the electrical resistivity ($\rho$) increased from 27 to 155 ${\mu}$$\Omega$cm. The coercivity (H$\sub$c/) exhibits the minimum value at 4% of P$\sub$N2/. The magnetic anisotropy (H$\sub$k/) are in the range of 20∼50 Oe. High frequency characteristics of (Co$\sub$22.2/Ni$\sub$27.6/Fe$\sub$50.2/)$\sub$100-x/N$\sub$x/ films are excellent in the range of 3∼5% of P$\sub$N2/. Especially the effective permeability of the film fabricated at 4% of P$\sub$N2/ is 800, which is maintained up to 600 MHz. This film also shows Bs of 17.5 kG, H$\sub$c/ of 1.4 Oe, resistivity of 98 $\Omega$cm and H$\sub$k/ of about 25 Oe. Also, the corrosion resistance of (Co$\sub$22.2/Ni$\sub$27.6/Fe$\sub$50.2/)$\sub$100-x/N$\sub$x/ were improved with the increase in N concentration.

• YAKHAK HOEJI
• /
• v.41 no.1
• /
• pp.60-73
• /
• 1997

In order to design a 24 hr sustained release preparation of sulindac for oral administration, fast release pellet (FR), slow release pellet (SR) and two combined formulation (1 : 1 and 1 : 2) were prepared. The pharmacokinetic effect of such preparations has been evaluated using rabbits as a suitable in vivo model, and tested in man. Dose determination was carried out using curve fitting according to RSTPJP II program. In bioavailability test using rabbit, AUCs of sulindac in a few designed formulations were similar to each other. $C_{max}$- of RF and SR were 1.8 times and 1.2 times higher, respectively, compared to that of combined formulation (FR:SR=1:1). While plasma concentration of FR and SR decreased rapidly, that of combined formulation (FR:SR 1:1) lasted at the level close to $C_{max}$ for 24 hrs. Plasma concentration of sulfide form from the combined pellet(FR:SR=1:1) lasted for 24 hrs, and its AUC value was 1.4-fold, 2.7-fold. and 1.2-fold greater than FR pellet, SR pellet and combined pellet (FR:SR 1 : 2). Thus, the combined pellet of 1:1 ratio was found to be the most effective for oral sustained release formulation. Bioavailability test in human showed that AUC of sulfide from TSRP (1 : 1) was approximately 1.5 times greater than total AUC of Immbaron$^{\circledR}$ administered twice in a day. While $T_{max}$ of sulfide from lmmbaron$^{\circledR}$ was 4.33 +/- 1.37 hr (lst administration) and 3.33 ${pm}$ 0.82 hr (2nd administration), respectively, that of sulfide from TSRP increased to 7.17 ${pm}$ 2.86 hr. Plasma concentration of sulfide from TSRP was sustained at more, than 1.0 ${\mu}g{\cdot}$hr/ml until 24 hrs after one dose administration. In addition, TSRP may decrease local adverse reaction in the stomach, since plasma concentration of sulfide from the combined pellet was low within 2hrs in the stomach. In conclusion, it is suggested that TSRP formulation may be effective for oral 24 hr sustained release formulation of sulindac dosing 300 ~ 350mg once a day.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.965-970
• /
• 2005

In this paper, SPDT Tx/Rx MMIC switch applicable to IEEE 802.11a WLAN systems is designed and fabricated using a specific designed epitaxial layered pHEMT wafer and ETRI's $0.5{\mu}m$ pHEMT switch process. The SPDT switch exhibits a low insertion loss of 0.68dB, high isolation of 35.64dB, return loss of 13.4dB, power transfer capability of 25dBm, and 3rd order intercept point of 42dBm at frequency of 5.8GHz and control voltage of 0/-3V. The comparison of the measured performances with commercial products based on the GaAs pHEMT technology for low voltage operating at ${\pm}$ 3V/0V shows that the return loss is somewhat inferior to the commercial products and insertion loss is compatible with each other however, isolation characteristics are much better than in conventional chips. Based on these performances, we can conclude that the developed SPDT switch MMIC has an enough potential for IEEE802.11a standard 5 GHz-band wireless LAN applications.

• KSBB Journal
• /
• v.21 no.6 s.101
• /
• pp.422-427
• /
• 2006

The culture media from Fomitopsis pinicola were extracted by methanol and examined growth inhibition against Helicobacter pylori. The culture media from 8 days fermentation of F. pinicola showed maximum inhibition activity on H. pylori in 0.25 mg as MIC value. The highest activity against H. pylori by MHCS agar diffusion medium by Fp-P1 in 22.7 mm ID among 3 peaks from methanol fraction of 8 days culture media of Fomitopsis pinicola which purified by ion-exchange chromatography. The Fp-P1 from DEAE-Sephadex A-25 have been analysed by TLC as Fp-T1, Fp-T2 and Fp-T3 by ninhydrin staining. Fp-T3 (Rf value : 0.67) was higher activity against H. pylori in 14.4 mm ID. Fp-T3 was identified as single band by HPLC and TLC. It was assumed to aminosugar by BioLC analysis and TLC staining.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.2
• /
• pp.200-206
• /
• 2014

We investigated the in vitro and in vivo anti-obesity effects of extracts from young Akebia quinata D. leaves, including hot water (AQH) and 80% ethanol (AQE) extracts. The inhibitory effects of AQH and AQE on lipid accumulation in 3T3-L1 cells were examined by Oil Red O staining. Compared to control, lipid accumulation was significantly reduced by 18.3% with the treatment upon AQE at a concentration of $5{\mu}g/mL$. The levels of intracellular triglycerides and free glycerol were also reduced by 52.8% and 9.1% at the same concentration of AQE. The in vivo anti-obesity effect of AQE was evaluated in terms of body and white adipose tissue weights in ICR mice. Experimental groups were divided into the following five groups: normal diet (ND), high fat diet (HFD), high fat diet with 60 mg/kg/day of Orlistat (HFD-RF), high fat diet with 200 mg/kg/day of AQE (HFD-AL), and high fat diet with 600 mg/kg/day of AQE (HFD-AH). Feeding of HFD for eight weeks resulted in significant increases in body weight as well as weight gain compared to the ND group. HFD-AH group showed reduced body weight, weight gain, epididymal white adipose tissue weight, and perirenal white adipose weight as compared to the HFD group. These results indicate that AQE supplementation might have beneficial effects on anti-obesity by inhibiting lipid accumulation.

• Korean Journal of Food Science and Technology
• /
• v.5 no.4
• /
• pp.201-205
• /
• 1973

In order to eliminate aflatoxin in foodstuffs, the effects of the treatment by various pH conditions, acid and alkali, and salt on each temperature and time were studied in this experiment and the results were as follows: 1) In the low pH, aflatoxins were much more destroyed than high pH. The destruction of aflatoxins was significantly increased by heat in the same pH levels. 2) BY the treatment of 1.5 and 10% of sodium hydroxide and ammonia, aflatoxins were completely eliminated, but $40{\sim}80%$ of aflatoxins were eliminated by the treatment of 1.5 and 10% of acetic acid, hydrochloric acid and sulfuric acid. 3) By the treatment of aflatoxin in bile acid and artificial gastric juice, aflatoxins were completly eliminated and 75% respectively. 4) By the boiling $(100^{\circ}C)$ for 30 minutes in salt solution, $39{\sim}55%$ of aflatoxins was eliminated and no variation was observed as the concentration.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.478-478
• /
• 2012

Recently, there are many researches in order to increase the deposition rate (D/R) and improve film uniformity and quality in the deposition of microcrystalline silicon thin film. These two factors are the most important issues in the fabrication of the thin film solar cell, and for the purpose of that, several process conditions, including the large area electrode (more than 1.1 X 1.3 (m2)), higher pressure (1 ~ 10 (Torr)), and very high frequency regime (VHF, 40 ~ 100 (MHz)), have been needed. But, in the case of large-area capacitively coupled discharges (CCP) driven at frequencies higher than the usual RF (13.56 (MHz)) frequency, the standing wave and skin effects should be the critical problems for obtaining the good plasma uniformity, and the ion damage on the thin film layer due to the high voltage between the substrate and the bulk plasma might cause the defects which degrade the film quality. In this study, we will propose the new concept of the large-area multi-electrode (a new multi-electrode concept for the large-area plasma source), which consists of a series of electrodes and grounds arranged by turns. The experimental results with this new electrode showed the processing performances of high D/R (1 ~ 2 (nm/sec)), controllable crystallinity (~70% and controllable), and good uniformity (less than 10%) at the conditions of the relatively high frequency of 40 MHz in the large-area electrode of 280 X 540 mm2. And, we also observed the SEM images of the deposited thin film at the conditions of peeling, normal microcrystalline, and powder formation, and discussed the mechanisms of the crystal formation and voids generation in the film in order to try the enhancement of the film quality compared to the cases of normal VHF capacitive discharges. Also, we will discuss the relation between the processing parameters (including gap length between electrode and substrate, operating pressure) and the processing results (D/R and crystallinity) with the process condition map for ${\mu}c$-Si:H formation at a fixed input power and gas flow rate. Finally, we will discuss the potential of the multi-electrode of the 3.5G-class large-area plasma processing (650 X 550 (mm2) to the possibility of the expansion of the new electrode concept to 8G class large-area plasma processing and the additional issues in order to improve the process efficiency.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.65-65
• /
• 2012

Copper zinc tin sulfide ($Cu_2ZnSnS_4$, CZTS) is a very promising material as a low cost absorber alternative to other chalcopyrite-type semiconductors based on Ga or In because of the abundant and economical elements. In addition, CZTS has a band-gap energy of 1.4~1.5eV and large absorption coefficient over ${\sim}10^4cm^{-1}$, which is similar to those of $Cu(In,Ga)Se_2$(CIGS) regarded as one of the most successful absorber materials for high efficient solar cell. Most previous works on the fabrication of CZTS thin films were based on the vacuum deposition such as thermal evaporation and RF magnetron sputtering. Although the vacuum deposition has been widely adopted, it is quite expensive and complicated. In this regard, the solution processes such as sol-gel method, nanocrystal dispersion and hybrid slurry method have been developed for easy and cost-effective fabrication of CZTS film. Among these methods, the hybrid slurry method is favorable to make high crystalline and dense absorber layer. However, this method has the demerit using the toxic and explosive hydrazine solvent, which has severe limitation for common use. With these considerations, it is highly desirable to develop a robust, easily scalable and relatively safe solution-based process for the fabrication of a high quality CZTS absorber layer. Here, we demonstrate the fabrication of a high quality CZTS absorber layer with a thickness of 1.5~2.0 ${\mu}m$ and micrometer-scaled grains using two different non-vacuum approaches. The first solution-processing approach includes air-stable non-toxic solvent-based inks in which the commercially available precursor nanoparticles are dispersed in ethanol. Our readily achievable air-stable precursor ink, without the involvement of complex particle synthesis, high toxic solvents, or organic additives, facilitates a convenient method to fabricate a high quality CZTS absorber layer with uniform surface composition and across the film depth when annealed at $530^{\circ}C$. The conversion efficiency and fill factor for the non-toxic ink based solar cells are 5.14% and 52.8%, respectively. The other method is based on the nanocrystal dispersions that are a key ingredient in the deposition of thermally annealed absorber layers. We report a facile synthetic method to produce phase-pure CZTS nanocrystals capped with less toxic and more easily removable ligands. The resulting CZTS nanoparticle dispersion enables us to fabricate uniform, crack-free absorber layer onto Mo-coated soda-lime glass at $500^{\circ}C$, which exhibits a robust and reproducible photovoltaic response. Our simple and less-toxic approach for the fabrication of CZTS layer, reported here, will be the first step in realizing the low-cost solution-processed CZTS solar cell with high efficiency.

• Journal of Technologic Dentistry
• /
• v.30 no.1
• /
• pp.25-31
• /
• 2008

Cp-Ti and Ti-6Al-4V alloys commonly used dental implant materials, particularly for orthopaedic and osteosynthesis because of its suitable mechanical properties and excellent biocompatibility. This alloys have excellent corrosion behavior in the clinical environment. The first factor to decide the success of dental implantation is sufficient osseointegration and high corrosion resistance between on implant fixture and its surrounding bone tissue. In this study, in order to increase corrosion resistance and biocompatibility of Cp-Ti and Ti-6Al-4V alloy that surface of manufactured alloy was coated with TiN by RF-magnetron sputtering method. The electrochemical behavior of TiN coated Cp-Ti and Ti-6Al-4V alloy were investigated using potentiodynamic (EG&G Co, PARSTAT 2273. USA) and potentiostatic test (250mV) in 0.9% NaCl solution at 36.5 $\pm$ 1$^{\circ}C$. These results are as follows : 1. From the microstructure analysis, Cp-Ti showed the acicular structure of $\alpha$-phase and Ti-6Al-4V showed the micro-acicular structure of ${\alpha}+{\beta}$ phase. 2. From the potentiodynamic test, Ecorr value of Cp-Ti and Ti-6Al-4V alloys showed -702.48mV and -319.87mV, respectively. Ti-6Al-4V alloy value was higher than Cp-Ti alloy. 3. From the analysis of TiN and coated layer, TIN coated surface showed columnar structure with 800 nm thickness. 4. The corrosion resistance of TiN coated Cp-Ti and Ti-6Al-4V alloys were higher than those of the non-coated Ti alloys in 0.9% NaCl solution from potentiodynamic test, indicating better protective effect. 5. The passivation current density of TiN coated Cp-Ti and Ti-6Al-4V alloys were smaller than that of the noncoated implant fixture in 0.9% NaCl solution, indicating the good protective effect resulting from more compact and homogeneous layer formation.