• Wind and Structures
• /
• 제26권5호
• /
• pp.317-329
• /
• 2018

Wake characteristics of the flow over a finite square prism at different incidence angles were experimentally investigated using an open-loop wind tunnel. A finite square prism with a width D = 15 mm and a height H = 7D was vertically mounted on a horizontal flat plate. The Reynolds number was varied from $6.5{\times}10^3$ to $28.5{\times}10^3$ and the incidence angle ${\alpha}$ was changed from $0^{\circ}$ to $45^{\circ}$. The ratio of boundary layer thickness to the prism height was about ${\delta}/H=7%$. The time-averaged velocity, turbulence intensity and the vortex shedding frequency were obtained through a single-component hotwire probe. Power spectrum of the streamwise velocity fluctuations revealed that the tip and base vortices shed at the same frequency as that ofspanwise vortices. Furthermore, the results showed that the critical incidence angle corresponding to the maximum Strouhal number and minimum wake width occurs at ${\alpha}_{cr}=15^{\circ}$ which is equal to that reported for an infinite prism. There is a reduction in the size of the wake region along the height of the prism when moving away from the ground plane towards the free end.

• Ocean Systems Engineering
• /
• 제1권4호
• /
• pp.355-372
• /
• 2011

Based on the fully nonlinear velocity potential theory, the liquid sloshing in a three dimensional tank under random excitation is studied. The governing Laplace equation with fully nonlinear boundary conditions on the moving free surface is solved using the indirect desingularized boundary integral equation method (DBIEM). The fourth-order predictor-corrector Adams-Bashforth-Moulton scheme (ABM4) and mixed Eulerian-Lagrangian (MEL) method are used for the time-stepping integration of the free surface boundary conditions. A smoothing scheme, B-spline curve, is applied to both the longitudinal and transverse directions of the tank to eliminate the possible saw-tooth instabilities. When the tank is undergoing one dimensional regular motion of small amplitude, the calculated results are found to be in very good agreement with linear analytical solution. In the simulation, the normal standing waves, travelling waves and bores are observed. The extensive calculation has been made for the tank undergoing specified random oscillation. The nonlinear effect of random sloshing wave is studied and the effect of peak frequency used for the generation of random oscillation is investigated. It is found that, even as the peak value of spectrum for oscillation becomes smaller, the maximum wave elevation on the side wall becomes bigger when the peak frequency is closer to the natural frequency.

• 한국주거학회논문집
• /
• 제26권6호
• /
• pp.83-92
• /
• 2015

The purpose of this study is to analyze the characteristics of exterior spaces used by the elderly of housing complex. The exterior spaces are used for going out in everyday life with the view point that the elderly have to go out from the inside home in order to prevent isolating the elderly from local community. For that Toyoshikidai housing complex in Kashiwa city of Chiba prefecture, Japan is selected and carried out questionnaire survey and field survey targeting residents. The results are following as. For spatial characteristics, the location installed benches, location occupied in one part by roof, wall, or plants, place connecting to moving flow of the aged, and an open expanse getting safety from vehicle are taken advantages for the elderly. For using benches, the elderly of 70.1% do not have experience using benches installed in all those places. The the biggest reason is that they are not tired. However, 36.8% of the elderly are using benches in order to take a rest and 20.8% of them are using benches in order to talk with the other people. Bench is ibasho of the elderly.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2145-2150
• /
• 2003

Ejector system is one of fluid machinery which can entrain the fluid in low pressure part and transport it to the higher pressure part. The ejector system has been widely used for the purpose of obtaining high-vacuum state, fluid transport, thrust augmentation, etc. It can transport a large capacity of fluid with relatively small device of no any moving parts, and thus seldom causes mechanical troubles. However, the conventional ejector system has been pointed out that its overall efficiency is quite low compared with other fluid machinery since it is derived by only the pure shear stresses. In the present study, 4, 6, and 8 lobed petal nozzles with a design Mach number of 1.7 are adopted as a primary nozzle to improve the ejector performance, and are compared with a conventional circular nozzle. The static pressures along the diffuser wall are measured to qualify the flow field inside the supersonic petal ejector system.

• 한국생산제조학회지
• /
• 제23권4호
• /
• pp.374-379
• /
• 2014

Mobile robots with omni-directional wheels can generate instant omni-directional motion without requiring extra space to change the direction of the body. Therefore, they are capable of moving in an arbitrary direction under any orientation even in narrow aisles or tight areas. In this research, an omni-directional mobile robot based on Mecanum wheels was developed to achieve omni-directionality. A CompactRIO embedded real-time controller and C series motion and I/O modules were employed in the control system design. Ultrasonic sensors installed on the front and lateral sides were utilized to measure the distance between the mobile robot and the side wall of a workspace. Through intensive experiments, a performance evaluation of the mobile robot was conducted to confirm its feasibility for industrial purposes. Mobility, omni-directionality, climbing capacity, and tracking performance of a squared trajectory were selected as performance indices to assess the omni-directional mobile robot.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.998-1003
• /
• 2003

Ultrasonic flow metering(UFM) technology is being received much attention from a variety of industrial fields to exactly measure the flow rate. The UFM has much advantage over other conventional flow meter systems, since it has no moving parts, and offers good accuracy and reliability without giving any disturbances to measure the flow rate, thereby not causing pressure losses in the flow fields. In the present study, 3-dimensional, unsteady, compressible Navier-Stokes equations are solved by a finite volume scheme, based upon the second order upwind scheme for spatial derivatives and the multi-stage Runge-Kutta integral method for time derivatives. In order to simulate multi-path ultrasonic flow meter, an excited pressure signal is applied to three different locations upstream, and the pressure signals are received at three different locations downstream. The mean flow velocities are calculated by the time difference between upstream and downstream propagating pressure signals. The obtained results show that the present CFD method simulates successfully ultrasonic meter gas flow and the mean velocity measured along the chord near the wall is considerably influenced by the boundary layers.

• 한국추진공학회지
• /
• 제12권3호
• /
• pp.68-75
• /
• 2008

이전에 개발된 병렬 해석 코드를 이용하여 원형 관내에서의 삼차원 데토네이션 파 전파 특성을 관찰 하였다. 일련의 해석을 통하여 직경이 일정한 원형 관에서 반응 속도 상수 값 k에 의존하는 데토네이션 셀 생성 메커니즘을 알 수 있었다. 삼차원 유동에 대한 비정상 유동의 해석 결과는 two-, three-, four-cell 구조의 메커니즘을 잘 보여주었으며, 반응속도 상수 k가 증가함에 따라 생성되는 셀 수가 증가하고 셀의 폭과 길이는 감소하였다. 모든 다중-셀 모드에서 데토네이션 파의 구조와 그을음막 기록은 횡단파의 움직임에 의하여 만들어지며, 데토네이션 파면은 주기적으로 일정한 다각형 및 풍차 형상을 가지게 된다.

• 공업화학
• /
• 제20권5호
• /
• pp.547-552
• /
• 2009

본 연구에서는 fiber reinforced plastics (FRP) 제품 가공시 발생하는 분진 및 악취 물질로 인한 작업현장의 악조건을 개선하기 위하여 activated carbon fiber (ACF) 장착 하이브리드 백필터를 개발하였다. FRP 제조업체 2개사에 ACF 백필터를 설치함에 있어 천장, 벽하단 부분에 덕트를 설치함은 물론 이동식 집진 덕트를 설치함으로써 집진효율을 높였다. 펄스젯트식 탈진방식을 채택하여 효과적인 시스템 운영을 유도함으로써 작업환경을 개선하고자 하였다. 하이브리드 백필터 시스템 운용시 이에 따르는 분진과 악취에 대한 제거동향을 고찰하였다.

• 한국실내디자인학회논문집
• /
• 제17권2호
• /
• pp.83-90
• /
• 2008

This study attempts to understand the arrangement and spatial requisites of art pieces by materializing the visitors' path of movement in the exhibition space, as well as researching their behavior. The purpose of the research is to the guideline for planning the exhibition layout and visitors' circulation can be derived in order to correspond to the visitors' characteristic of movement and circulation-path choice. Although such guideline may have limited use, it is still significant enough to be studied. Taking three Korean art galleries as the subjects of research, this study observes the arrangement of art pieces, movement path of visitors, characteristics of the visitors' behavior and the duration time a visitor takes to view an art piece without moving around in order to understand the arrangement and spatial requisites of art pieces which correspond to the visitors' behavior. The following results have been drawn in this research and analysis; First, when there is an island type exhibition other than the ordinary on-the-wall display in the exhibition space, the visitors' choice of path changes. In short, an island type exhibition seems to be a factor that changes the visitors' path. Second, in the entrance of an exhibition space unit, most of the visitors seem to choose a path which moves counter-clockwise. Third, it is considered that well-known art pieces or art pieces with a big size shall not be displayed on the comer of the exhibition room.

• 한국자동차공학회논문집
• /
• 제23권1호
• /
• pp.74-87
• /
• 2015

A numerical parametric study has been accomplished to figure out the effect of grille shape built in a small passenger car on the aerodynamic performance such as drag and mass flow rate through CRFM(Condenser Radiator Fan Module). Three grille opening parameters and three grille mesh parameters are selected and adopted to a simple shape passenger car model. This research will provide a design guideline for grille opening geometry and mesh shape in the grille. FLUENT, which is very well known commercial code, hires k-${\epsilon}$ turbulence model at the driving speed of 110km/h with moving wall boundary condition. A porous media condition is prepared to estimate the pressure drop amount through CRFM parts.