• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.17-17
• /
• 2011

As a method of countermeasure to bed degradation and armoring phenomena of bed material in the downstream area of dam reservoirs, sediment augmentation (replenished sediment) has been carried out in many Japanese rivers. In general, bed of the replenished sediment site is composed of rocks, because the site is located in the downstream area of the dams and sediment supply is very small. Bed deformation process has been researched by many researchers. As a method of countermeasure to bed degradation and armoring phenomena of bed material in the downstream area of dam reservoirs, sediment augmentation (replenished sediment) has been carried out in many Japanese rivers. In general, bed of the replenished sediment site is composed of rocks, because the site is located in the downstream area of the dams and sediment supply is very small. Bed deformation process has been researched by many researchers. However, most of them can treat movable bed only and cannot be applied to the bed deformation process of sediment on rocks. If the friction angle between the sediment and the bed surface is assumed to be the same as the friction angle between the sediment and the sediment, sediment transport rate must be smaller without sediment deposition layer on the rocks. As a result, the reproduced bed geometry is affected very well. In this study, non-equilibrium transport process of non-cohesive sediment on rigid bed is introduced into the horizontal two dimensional bed deformation model and the model is applied to the erosion process of replenished sediment on rock in the Nakagawa, Japan. Here, the Japanese largest scale sediment augmentation has been performed in the Nakagawa. The results show that the amounts of the eroded sediment and the remained sediment reproduced by the developed numerical model are $56300m^3$ and $26800m^3$, respectively. On the other hand, the amounts of the eroded sediment and the remained sediment measured in the field after the floods are $56600m^3$ and $26500m^3$, respectively. The difference between the model and field data is very small. Furthermore, the bed geometry of the replenished sediment after the floods reproduced by the developed model has a good agreement with the measured bed geometry after the floods. These results indicate that the developed model is able to simulate the erosion process of replenished sediment on rocks very well. Furthermore, the erosion speed of the replenished sediment during the decreasing process of the water discharge is faster than that during the increasing process of the water discharge. The replenished sediment is eroded well, when the top of the replenished sediment is covered by the water. In general, water surface level is kept to be high during the decreasing process of the discharge during floods, because water surface level at the downstream end is high. Hence, it is considered that the high water surface level during the decreasing process of the water discharge affects on the fast erosion of the replenished sediment.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.558-558
• /
• 2015

하천 시설물은 홍수시 혹은 비상시 운영할 수 있는 경보시스템이나 관리지침 등의 마련이 필수적임에도 불구하고, 현재까지 가동보 시설물에 대한 비상시 운영 메뉴얼 및 경보시스템이 구축되지 못한 실정이다. 4대강 살리기 사업이나 하천정비사업과 같은 대표적인 하천관련 사업에서 단순한 하천 이 치수 목적뿐만 아니라 소수력 발전, 친수공간조성 등의 다목적 활용을 위하여 가동보 설치 사업이 다수 수행되었으며, 현재 국내 하천에 약 1,200여개의 가동보가 설치 운영되고 있다. 이와 같이 다목적 활용을 위하여 가동보의 수요가 급증하는데 반해, 각 설치 현장 상황에 적합한 가동보 운영지침이나 비상경보시스템이 구축되지 못한 실정이며, 적절한 지침 없이 관행적인 가동보 방류로 인한 물놀이 안전사고나 인명피해가 속출하고 있는 실정이다. 2012년 11월에는 하천 제수변 공사를 위해 전주천에 설치한 가동보를 임시적으로 방류하였는데, 하류측의 안전을 확인하지 않고 관행적으로 가동보를 방류하였고, 경보시스템의 부재로 인하여 가동보 하류측 징검다리를 건너는 유치원생들이 급류에 휩쓸리는 사고가 발생하였고, 최근 2014년 5월에는 수원시에 위치한 원천저수지 여수로 둑에 설치된 가로 34m 높이 1.6m 크기의 가동보가 공기압축기의 오작동으로 인하여 보 높이가 낮아지면서 약 30분 원천저수지 하류의 원천리천에 갑자기 무리 불어나 산책로가 침수되고 인근에 산책하던 주민들이 휩쓸려 떠내려가는 사고가 발생하였다. 해외에서도 가동보 운영 미숙으로 인하여 인명사고가 발생하는데, 2008년 11월 호주에서는 하류측 상황 점검이나 경고 방송 없이 가동보를 도복시켜 4살 여아가 급류에 사망하는 사고가 발생하였다. 국외의 경우에는, 상류측 홍수 수위나 하류측 역류 수위를 조절하기 위하여 가동보의 높이를 제어하는 시스템을 구비하고 있지만 이러한 시스템 역시 단순한 수위조절 기능으로서 가동보의 방류량을 제어하지 못하는 실정이다. 가동보를 운영하기 위한 조작시스템은 국내의 경우, 조작실의 조작판넬을 이용하여 가동보의 기립/도복 조작이나 원격 조작 기능과 같은 단순기능만을 구비하고 있어 가동보 방류시 하류측의 범람 피해를 야기하고 있다. 본 연구에서는 가동보 방류에 의한 하류측 범람 피해를 최소화하기 위하여 (1) 가동보 도복에 의한 방류량 산정 알고리즘을 개발하고, (2) 방류량에 따른 하류측 수위상승 범위 예측 기법을 개발하고, (3) 가동보 도복 속도를 제어하는 방류량 제어시스템을 개발하고, (4) 가동보 방류에 의한 비상경보시스템을 개발하였다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.1
• /
• pp.51-57
• /
• 2011

Irregular distributions of limestone cavity in Gang-Won province area may cause unexpected accidents from reduced serviceability or failure of structure. It is requested that an appropriate ground reinforcement method should be used to improve bearing capacity of structure, and the method should also be satisfied with environmental requirements. Among several methods used for foundation constructions in cavity area, Rod Jet Pile(RJP) method has been widely used. While the RJP method was used to improve bearing capacity for the railway bridge foundations, water pollutions of drinking water as well as fishery located adjacent to this project area were occurred. The main reason of the water pollution was cement runoff used in cement mortar during injecting material in RJP method. Laboratory tests were performed to prevent water pollution. The compaction mortar method using low movable material was selected for this project. The quality of water at a fishery adjacent to the site and the compressive strength of cores taken from the construction site were measured. Test results show that the water pollutions was minimized, and the average compressive strength of foundation material was over 5 MPa. As a result of this study, compaction mortar method can be used to ensure the bearing capacity of foundation and to prevent environment pollutions.

• Journal of Conservation Science
• /
• v.37 no.5
• /
• pp.590-605
• /
• 2021

The history of printing technology in Korea is studied by investigating existing ancient documents and records and comparing accumulated data and knowledge. Cultural property research requires non-destructive testing and observation with the naked eye or aided by a microscope. Researchers' experience and knowledge are required even though they cannot guarantee the outcome. For ancient documents and records that are presumed to consist of woodblock printing, wood type printing, metal type printing, or their combinations, each researcher draws various opinions and conclusions. This often causes confusion and divides the opinions of ordinary citizens and field specialists. Among them, the criteria for judging ancient documents or books printed using woodblock and metal movable material are ambiguous. Academic research on the development history of printing technology in ancient Korea has been stagnant, and conflicts among researchers have also erupted. Involvement of national investigative agencies not specialized in cultural properties has exacerbated the situation. In this study, we investigated printing characteristics that are likely to serve as more objective judgment criteria by quantitatively analyzing the experiments of retrieving several sheets of Korean paper (Hanji) using a replicated Hunminjeongeum (訓民正音) woodblock and quantitatively analyzing the images of the printed papers. In addition, the validity and questions for the typical phenomena presented as a method for distinguishing between woodblock and metal print are reviewed. We investigated the possibility of developing new objective judgement criteria through quantitative analysis using image analysis and investigating the printing characteristics of Korean paper through a reproduction experiment of woodblock printing.

• Journal of Climate Change Research
• /
• v.9 no.4
• /
• pp.319-324
• /
• 2018

Due to climate change, water shortages and water-related disasters will be serious. Since the damage and frequency of drought are increasing, the importance of water resource management technology is increasing. In this study, we analyzed the amount of greenhouse gas and the environmental impact caused by the production and operation system technologies of movable weir among various water resource management technologies. The research subjects were air inflatable rubber dams widely used in rivers and upright type rubber dams, which are an improvement on the existing rubber type. Each type of dam was studied at sizes of $1,500H{\times}10,000L\;mm$ and $3,000H{\times}20,000L\;mm$, and the two types and two sizes were compared and analyzed. Using life cycle assessment, we examined the environmental impacts using the amount of electricity required for operation and the discretionary amount required for production. In the '$1,500H{\times}10,000L$' dams, the global warming indexes were $9.35E+04kg\;CO_2-eq$. for upright type and $7.36E+04kg\;CO_2-eq$. for inflatable type. At size of '$3,000H{\times}20,000L$' the global warming indexes were $9.09E+05kg\;CO_2-eq$. for upright type and $1.07E+06kg\;CO_2-eq$. for inflatable type. Analysis of the life cycle environmental impact showed that the environmental impact of the air inflatable rubber dam was reduced by 39.8% at '$1,500H{\times}10,000L$' compared to the larger size. At the larger '$3,000H{\times}20,000L$' size, the upright dam showed a 10.1% smaller impact than the air inflatable rubber dam. Selection of water resource management system should consider climate change, not only management purpose and cost. Additional studies and improvements on rubber dam systems should be made.

• Journal of Korea Technology Innovation Society
• /
• v.21 no.3
• /
• pp.1155-1178
• /
• 2018

Future automobiles are evolving into movable living spaces capable of eco-friendly autonomous driving. The role of electrically processing, controlling, and commanding various information in the vehicle is essential. It is expected that the automotive semiconductor will play a key role in the future automobile such as self-driving and eco-friendly automobile. In order to foster the automotive semiconductor industry, it is necessary to grasp technology trends and to acquire technology and quality that reflects the requirements in advance, thereby achieving technological innovation with industrial competitiveness. However, there is a lack of systematic analysis of technology trends to date. In this study, we analyzed the technology trends of automotive semiconductors using patent analysis and topic model, and confirmed technologies such as electric cars, driving assistance, and digital manufacturing. The technology trends showed that element technology and technical characteristics change according to technology convergence, market needs, and government regulations. Through this research, it is expected that it will help to make R&D policy for automotive semiconductor industry and to make decision for industrial technology strategy establishment. In addition, it is expected that it will be used effectively in detail research direction and patent strategy establishment by providing detailed classification of technology and trend analysis result of technology.

• Journal of the Society of Disaster Information
• /
• v.15 no.3
• /
• pp.358-366
• /
• 2019

Purpose: This paper aims to clarify the problems and to examine the improvement methods by investigating the management condition of local-designated cultural property of which management is relatively poor in comparison with state-designated cultural heritage. Method: In order to grasp the management situation of the local-designated cultural heritage, a research on cultural heritage management situation and problems will be carried out with 35 cultual heritages in Goryeong-gun. Also, the improvement methods about the property type vulnerability on the basis of interview with cultual property managers, fire-fighting officers and civil servants, etc. Results: Local cultural heritages were investigated to be very vulnerable to the fire of wooden buildings, the theft of movable cultural heritages, and the effects of wind and water damage. It is because cultural heritages are scattered over wide areas fundamentally. As the result, it has difficulty in the patrols of police officers and fire fighters, and in the situation that it lacks disaster monitoring and CCTV for countermeasures to replace them, electronic security including fire hydrant, sensors, etc and fire extinguishing facilities and so on. It is difficult for local governments managing local-designated cultural heritages to enhance their management systems directly due to their lack of budget and manpower. Conclusion: In order to strengthen disaster and safety management system for the cultural heritages designated by local governments, they have to clarify disaster countermeasure task of fire fighting, police, and cultural heritage managers prepare their manuals, and systematize them through disaster drill mainly in local autonomous governments. Also, so as to establish a surveillance system every day, they have to enhance the community for local cultural heritage manage consisting of local volunteer fire departments, local voluntary disaster prevention organizations, volunteers, etc.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.2
• /
• pp.297-306
• /
• 2019

Since the centrifugal force acts on the flow in the curved channel, a transverse water surface gradient occurs and the thalweg is biased toward the outer bank. The submerged vanes may be used to solve various engineering problems of the curved channels. In order to analyze the influence of an attack angle and the distance between the vane arrays on the river bed variation and the superelevation in a bend, movable bed hydraulic experiments were conducted in a $90^{\circ}$ curved rectangular channel of a small-size gravel bed. Installing the submerged vanes in the bend increases the maximum scour depth. But if vanes are installed in a uniform obtuse angle, the scour depth may be reduced. If the flow rate in the channel bend with vanes equals to the channel forming discharge, the location of the maximum scour depth moved to the downstream and the superelevation increased. However if the flow rate is smaller than that, the location of the maximum scour depth moved upstream and the superelevation decreased. The channel bed change and the superelevation due to the installation of the submerged vanes have been dependent on the interaction of the attack angle, the flow rate, and the distance between the arrays.

• Quality Improvement in Health Care
• /
• v.25 no.1
• /
• pp.43-51
• /
• 2019

Purpose: The time lag between the decision to initiate continuous renal replacement therapy (CRRT) and its actual initiation remains a major barrier in our intensive care units. We developed a CRRT pop-up chart on EMR for managing CRRT machines. Methods: This study measured time interval between the decision to prepare the CRRT machine and the actual use of the machine before and after using a CRRT pop-up chart. This study conducted a questionnaire of the medical staff to assess the changes in the quality of CRRT preparation. Results: A total of 95 patients on CRRT is analyzed. The time to find an available CRRT machine is decreased by 24.6%. The time to move a CRRT machine to the patient's bedside is decreased by 55.8%. Medical surveys of 44 nurses gave the following results. 1) The time to apprehend machines for 1 to 3 minutes is improved from 29.5% to 81.8%, and the time to apprehend machines over 3 minutes is decreased from 70.5% to 18.2%. 2) The number (6-all) of known machine locations is improved from 22.7% to 63.4%. 3) Interruption of a nurse's work due to telephone calls asking for the possession of movable CRRT equipment also is improved. Scores of 1-4 are improved from 15.9% to 41%. Scores of 5-7 are reduced from 52% to 15.9%. Conclusions: CRRT pop-up chart is shortened the time lag of CRRT machine preparation, reduced the nurse's phone workload and helped to improve the quality of CRRT care.

• Applied Chemistry for Engineering
• /
• v.30 no.3
• /
• pp.384-388
• /
• 2019

In winter season, the snow and ice accretion on the bottom of the high speed railway rolling stock and boogie part has fallen at a high speed from the ballast section (gravel section for the transmission of the rolling stock load received by sleepers and fixing sleepers), causing the gravel to be scattered, thereby damaging the railway rolling stock structures and facilities. In order to solve these problems, the gravel scattering prevention net, manual de-icing, and movable hot air machine were used, but their efficiency was low. For the more efficient de-icing than ever before, an optimum material for de-icing fluid for high speed railway rolling stock was developed by evaluating the ice melting capacity, kinematic viscosity, evaporation of the material used as a chemical de-icing fluid. Four kinds of organic acid salts (sodium formate, sodium acetate, potassium formate and potassium acetate) and two different alcohols (propylene glycol, glycerol) were used as evaluation materials. Potassium formate, potassium acetate, and propylene glycol had similar ice melting capacities in the indoor test, but the propylene glycol showed the best ice melting capacity in spraying the system simulation test. This is because the kinematic viscosity of propylene glycol was 2.989029 St, which is higher than those of other materials therefore, it could stay longer on the ice and de-icing. In addition, potassium formate and potassium acetate were difficult to be used since the crystals precipitated and adversely affected the appearance of the rolling stock. The propylene glycol is the most optimum as an de-icing fluid for the high speed railway rolling stock.