• Journal of Biosystems Engineering
• /
• 제25권3호
• /
• pp.233-240
• /
• 2000

A commercially available Doppler radar was modified and evaluated for on-board monitoring of ground speed. The radar output was corrected for pitch angle of aircraft based on the output of an electrolytic tilt sensor. The effects of aircraft speed, height and mounting angle on error in the ground speed were evaluated. The speed error decreased with an increase of the mounting angle since the radar contact angle with respect to the ground approached to the mounting angle. The error increased with an increase of the nominal aircraft speed. The altitude insignificantly affected the speed error. The Doppler radar provided acceptable percent errors within 5% in most measurements. The error can be reduced within ${\pm}$1.5% by increasing the mounting angle ($43^{\circ}$). The error of -3.8% at the mounting angle of $29^{\circ}$could be reduced by adjusting the mounting angle with respect to the radar contact angle.

• 한국정밀공학회지
• /
• 제13권7호
• /
• pp.90-99
• /
• 1996

In the area of assembly process of micro-chips and electronic parts on the printed circuit board, surface mounting device(SMD) is used as a fundamental tool. Generally speaking, the motion of the SMD is based on the ball screw system operated by any type of actuators. The ball screw system is a mechanical transformed which converts the mechanical rotational motion to the translational one. Also, this system could be considered as an efficient motion device against mechanical backlash and friction. Therefore a dynamic modeling and state sensitivity analysis of the ball screw system in SMD have to be done in the initial design stage. In this paper, a simple mathematical dynamic model for this system and the sensit- ivity analysis are mentioned. Especially, the bond graph approach is used for graphical modeling of the dynamic system before analysis stage. And the direct differentiation method is used for the state sensit- ivity analysis of the system. Finally, some trends for the state variables with respect to the design variables could be suggested for the better design and faster operating based on the results of dynamic and state sensitivity.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.628-634
• /
• 1995

In the area of assembly process of micro-chips and electronic parts on the printed circuit board, surface mounting device(SMD) is used as a fundamental tool. Generally speaking, the motion of the SMD is based on the ball screw system operated by any type of actuators. The ball screw system is a mechanical transformer which converts the mechanical rotational motion to the translational one. Also, this system could be considered as an efficient motion device against mechanical backash and friction. Therefore a dynamic modeling and stste sensitivity analysis of the ball screw system in SMD have to be done in the initial design stage. In this paper, a simple mathematical dynamic model for this system and the sensitivity snalysis are mentioned. Especially, the bond graph approach is used for graphical modeling of the dynamic system before analysis stage. And the direct differentiation method is used for the state sensitivity analysis of the system. Finally, some trends for the state variables with respect to the design variables could be suggested for the better design based on the results on the results of dynamic and state sensitivity.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1996년도 춘계학술대회논문집; 부산수산대학교, 10 May 1996
• /
• pp.188-193
• /
• 1996

The purpose of resilient mounting for marine engine is to prevent noise and ship damages caused by engine vibration. Although many researches for the resilient mounting system have been carried out, these results have limit to apply on the marine engine systems. Because marine engine generally have low speed operating range and have to consider misfiring condition. In this paper, we studied the effect of engine's misfiring on the resilient mounting systems. And the influences of design parameters, such as dynamic characteristics and location angles of resilient rubber mountings, were also examined on the single and double resilient mounting systems.

• 한국해양공학회지
• /
• 제29권2호
• /
• pp.120-127
• /
• 2015

When a deep-seabed lifting pump is kept this device has bending and deformation in the axis due to its long length(8m). These influences can be caused a breakdown. Therefore, a mounting must be developed to keep the lifting pump safe. This paper discusses the hydraulic cylinder design of the lifting pump and structural safety estimation of the mounting using SBD(simulation-based design). The multi-body dynamic simulation method is used, which has been used in the automotive, structural, ship building, and robotics industries. In this study, the position and diameter of the hydraulic cylinder were determined based on the results of the strokes and buckling loads for the design positions of the hydraulic cylinder. A structural dynamic model of the mounting system was constructed using the determined design values, and the structural safety was evaluated using this dynamic model. According to these results, this system has a sufficient safety factor to manufacture.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.282-283
• /
• 2008

According to the development of vehicle technique, the improved NVH performance is required in the vehicle which have the high effectiveness and the high output of the powertrain. This vehicle has to be adapted to active engine mounting system to reduce the vibration in accordance with various vehicle information. The pneumatic active engine mounting system is consist with engine mount, solenoid valve, air tank and control unit totally. The important technique of this system is to reduce the vibration by the air pressure. This paper contains the development process of the pneumatic active engine mounting system and confirm the performance of this system test and vehicle test.

• Journal of Information Technology Applications and Management
• /
• 제11권2호
• /
• pp.29-43
• /
• 2004

As the development of an information technique, gradually, mobile device is going to be miniaturized and operates at high speed. By such the requirements, the devices using a flash memory as a storage media are increasing. The flash memory consumes low power, is a small size, and has a fast access time like the main memory. But the flash memory must erase for recording and the erase cycle is limited. JFFS is a representative filesystem which reflects the characteristics of the flash memory. JFFS to be consisted of LSF structure, writes new data to the flash memory in sequential, which is not related to a file size. Mounting a filesystem or an error recovery is achieved through the sequential approach. Therefore, the mounting delay time is happened according to the file system size. This paper proposes a MJFFS to use a multi-checkpoint information to manage a mass flash file system efficiently. A MJFFS, which improves JFFS, divides a flash memory into the block for suitable to the block device, and stores file information of a checkpoint structure at fixed interval. Therefore mounting and error recovery processing reduce efficiently a number of filesystem access by collecting a smaller checkpoint information than capacity of actual files. A MJFFS will be suitable to a mobile device owing to accomplish fast mounting and error recovery using advantage of log foundation filesystem and overcoming defect of JFFS.

• 한국산학기술학회논문지
• /
• 제14권10호
• /
• pp.4665-4671
• /
• 2013

엔진 설치 시스템은 차량의 NVH 성능에 매우 중요한 시스템 이다. 차량의 NVH 성능은 공회전 진동(Idle Vibration), 엔진 쉐이크(Engine Shake) 시동 진동(Key ON/OFF Vibration), 변속 진동(Gear Shift Vibration) 등 다양한 이론이 존재한다. NVH 성능 개선을 위해 이러한 이론들에 대한 실제적 최적화가 필요하며, 특히 최적의 엔진 설치 위치와 강성을 찾아내는 것이 매우 중요하다. 또한 효과적인 NVH 성능 개선을 위하여 차량개발 프로세스 측면에서 제약조건과 한계가 있는 사후 조정보다는 개발 초기에 최적화가 필요하다. 본 논문에서는 엔진 설치 시스템 관련 여러 이론에 대한 최적화 해석과 파워 트레인의 엄격한 모드 분리와 토크롤축(Torque Roll Axis), 탄성롤축(Elastic Roll Axis) 사이의 각도를 최소화 하는 다양한 시뮬레이션 케이스(Simulation Case)와 FE-모드를 개발초기에 수행하여 다중 최적화 분석을 함으로서 최적의 엔진 설치 위치와 강성을 찾아내어 NVH 성능을 개선하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.495-499
• /
• 2000

The booming noise of a vehicle is usually caused by the vibration of the vehicle's body transmitted from the engine through the mounting system. Thus the engine mounting system must be cautiously designed to reduce the noise. Vector synthesis analysis is performed to predict the booming noise when the characteristic of the engine mounting system is changed., i.e., when magnitudes and phases of vibratory forces after the mounts are altered. To effectively use the method, the concept of 'effectiveness' is introduced to identify the contributions of each vibration sources and transmission paths to interior noise. When the magnitudes and phases of the forces due to the engine vibration are changed, the synthesized interior booming noise level is predicted by the vector synthesis diagram. Thus, the optimum characteristics of the forces are obtained through the simulations of the vector synthesis analysis. It is shown that the vector synthesis method can be used to obtain the optimum design characteristic of the mounting system to control the interior booming noise of a vehicle.

• 한국측량학회지
• /
• 제30권1호
• /
• pp.31-38
• /
• 2012

UAV기반 멀티센서 시스템을 통해 취득된 영상의 지오레퍼런싱 정확도는 사용된 GPS/INS 시스템의 성능뿐만 아니라 카메라와 GPS/INS 시스템간의 상호관계를 나타내는 탑재변수의 정확도에 의해 영향을 받는다. 따라서 멀티센서 시스템 개발에 있어서 탑재변수의 정확한 추정은 필수적이다. 현재 우리는 재난/재해와 같은 긴급 상황에 대한 빠른 대응을 위해 실시간으로 대상지역을 감시할 수 있는 저고도 UAV기반의 실시간 공중자료획득 시스템을 개발하고 있다. 본 연구는 현재 개발 중인 시스템의 탑재변수 추정을 위한 시스템 캘리브레이션 방법론을 제안한다. 또한 실제 시스템의 제원을 이용한 시뮬레이션 데이터를 이용하여 정확하고 효율적인 캘리브레이션을 위한 효과적인 비행경로 및 지상기준점의 필요 개수를 도출하였다. 실험 결과, 총 6개의 스트립으로 구성된 비행경로를 따라 획득된 데이터와 5점 이상의 지상기준점 정보를 이용하면 제안된 방법론을 통해 정확한 탑재변수의 추정이 가능함을 확인할 수 있었다. 향후에는 제안된 방법론을 이용하여 개발된 시스템의 탑재변수를 추정하고 이를 이용하여 획득된 센서 데이터의 지오레퍼런싱 정확도 평가를 수행할 예정이다.