• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1998년도 제10회 학술강연회논문집
• /
• pp.21-21
• /
• 1998

추력방향 제어시스템 설계에 있어서 가장 기본적으로 요구되는 Requirement는 Rocket Motor의 추력, 요구되는 최대 Side Force, Rocket Motor의 외경, System의 총 구동시간, 구동후의 분리여부 등이다. 이러한 Requirement를 만족하기 위해서는 Nozzle 출구의 분출가스 물성치로부터 초음속 유동해석을 통하여 Vane 주위의 속도, 온도, 압력 분포를 구하고, Vane의 받음각 변화에 대한 Aerodynamic Force와 Moment를 계산하고, Side Force를 만족하는 최대 받음각의 결정, Torque를 만족하는 감속기와 Motor의 선정 및 Housing 기본 형상을 설계하였다. 금번 개발에서는 지상 시험용으로서 안전 계수를 Flight Model보다 약간 높게 설계하였으며, 작동 완료 후 System이 Nozzle로부터 떨어져나가는 분리시스템은 포함하지 않았다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.219-221
• /
• 2005

Various adjustment devices which present automobile uses electric motion motor of reducer built-in type for user's convenience are increasing. The example are seat control motor, sunroof motor, power windows motor etc. To get low noise, high effectiveness special quality in automobile DC motor of reducer built-in type, reducer department's transmission efficiency and noise, vibration quality are very important. The reducer used to DC motor of automobile reducer built-in type use worm gear for enough torque and proper number of rotation. We need optimization design technology of deceleration module including worm gear and housing for reducer development that have special quality of good quality.

• 동력기계공학회지
• /
• 제12권6호
• /
• pp.83-87
• /
• 2008

EPS(Electric Power Steering) system, which has replaced the hydraulic steering system(HPS or HPAS) in many passenger cars recently, have many merits such as low energy consumption, easy mounting, light weight and improvement of environmental pollution. However, EPS system has the problem of motor noise when motor is rotated, which can make a driver feel uncomfortable. There are many techniques to solve those problems, but they are not clear. It is necessary to evaluate the mechanical noise in steering systems, because an EPS has vibration sources such as at the motor gear reducer, manual gears and intermediate joints. In this paper, reduction technique of EPS motor noise is introduced.

• 전기의세계
• /
• 제28권1호
• /
• pp.59-66
• /
• 1979

The linearized models on per for mance dynamics of the pulse motor have been already proposed by many others. These models exhibit certain advantages of their own because of their simple formulation, but in many cases the models are proved to be inadequate for further accurate analysis of the motor dynamics, owing to impractical and rather rough assumptions in the derivation. In this study a dynamic state transition model is induced, using the equivalent circuit obtained from the operating principle of the variable reluctance pulse motor which turns out to be nonlinear equation. This nonlinear dynamic state equation is numerically analysed by the use of UNIVAC System/3(OS/3) digital computer at hand. In the course of the dynamic analysis of the performance characteristics of a testing motor, dependance of the inertia of rotor and load, the coefficient of viscous friction between rotor and housing, and the winding resistance of the stator is discussed and a comparative study of the machine constants is carried on as related to the design problem of the motor.

• 동력기계공학회지
• /
• 제16권5호
• /
• pp.26-31
• /
• 2012

A numerical study has been carried out to investigate the heat and mass transfer of an oil pumping system with a variable shape of the housing using the CFD method. Especially, the electric motor and the pump combined together, accomplishes a research about the oil supplying system. In this study, the temperature and velocity distribution of the oil pumping system by varying the flow rate of supplying oil have been investigated. The temperature changes with each five conditions(flow rate of supply oil : 2, 4, 8, 12, and 16 liter/min) have also been studied. The numerical results show that the exhaust temperature decreases as the flow rate of the supplying oil increases. It also reveals that the temperatures change differently with the housing shape.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.447-448
• /
• 2006

High speed machining is the core technology that influences the performance of machine tools, and the high speed motor spindle is widely used fur the high speed machine tools recently. The important problem in this spindle is to reduce and minimize the thermal effect by motor and bearing. In this study, the analysis of thermal characteristic of spindle is performed according to the cooling methods of housing by using finite element method. This result can be applied to the design and manufacture of the high speed spindle.

• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.29-34
• /
• 2014

Cooling the in-wheel motor in electric vehicles is critical to its performance and durability. In this study, thermal flow analysis was conducted by evaluating the thermal performance of two conventional cooling models for in-wheel motors under the continuous rating base speed condition. For conventional model #1, in which cooling oil was stagnant in the lower end of the motor, the maximum temperature of the coil was $221.7^{\circ}C$; for conventional model #2, in which cooling oil was circulated through the exit and entrance of the housing and jig, the maximum temperature of the coil was $155.4^{\circ}C$. Therefore, both models proved unsuitable for in-wheel motors since the motor control specifications limited the maximum temperature to $150^{\circ}C$.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.485-490
• /
• 2004

Flywheel Energy Storage System(FESS) consists of a high speed flywheel with an integral motor/generator suspended on non contact bearings and in an evacuated housing. Permanent magnet machines as the FESS motor/generator are a popular choice, since there are no excitation losses which means substantial increase in the efficiency. In this paper, the structural design method of rotor retainer for a high speed motor/generator are presented.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.3032-3036
• /
• 2011

Cooling type of traction motor for EMU in domestic is mostly an open type. Its system is a cooling air entered through air inlet cool down a traction motor and an hot air by traction motor get out air outlet. It is easy to cool it down but hard to maintain it. To improve an ability of maintenance, a total enclosed type traction motor is already developed and used in abroad, not an opne type. So we developed a total enclosed type traction motor which will be used in domestic and abroad EMU. We tried to reduce a weight and a size compared with the abroad one. In contrast with open type traction motors which cool off inside of motors, total enclosed motors cool down by cooling exterior frame of motors. In this case, cooling fins or air fan blowing to the exterior of motors are applied. The total enclosed type traction motor developed by us have two housing to block the foreign substance into inner of a motor and have two cooling fan to easy to reduce a heat happened at a coil. In this paper, design of a cooling structure of the total enclosed traction motor developed twice and performance verification through test will be discussed.

• Design & Manufacturing
• /
• 제11권3호
• /
• pp.13-18
• /
• 2017

The injection molding analysis of VCM (Voice Coil Motor) housing for smart phone cameras were performed. We conducted the analysis in terms of injection molding pressure, the formation of weld lines, flow marks, and flow patterns. The goal of the analysis was targeted for the prediction of the optimal gate locations. Because the quality of VCM housing is strongly dependent on the precise control of the camera lens by its nature, we focused on the lens guiding lanes in the VCM housing. We first calculated the maximum injection molding pressure in terms of the filled volumes. The injection molding pressure were calculated within 146MPa at about 90% volume filled. We also investigated the possibility of the occurrence of design-related defects such flow marks, weld lines. Filling patterns regarding the design of the gate locations were delineated to find the weld lines. Throughout the simulations, the final deformations of the lens guiding lanes for the VCM housing were calculated. The deformations distribute ranging from $0.5{\mu}m$ to $2.50{\mu}m$, which were used to find the optimal design of the gates.