• 전기학회논문지P
• /
• 제57권4호
• /
• pp.356-361
• /
• 2008

The conventional drive system of SRM has a current sensor per each phase. The torque demand signal generated by the outer control loop is translated into individual current reference signal for each phase. The torque is controlled by regulating these currents. Using the SRM in a variable-speed control, the phase currents are generally regulated to achieve a square wave. The simplest form of current regulation uses fixed frequency delta modulation of the phase voltages. The aim of this paper is to regulate 3-phases current of SRM by only single current sensor using delta modulation with digital chip. In this paper, the asymmetric bridge converter which is able to control independently phases and be excited simultaneously is used as the driver system for 6/4 poles SRM. And the current sensor is replaced 3 sensors of each phase with only one on bus line of converter so as to detect current of every phase. The proposed delta modulation technique has been implemented in a simple digital logic circuit using EPLD(Electrically Programmable Logic Device). This method is verified through simulation and experiment results.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.862-865
• /
• 2008

Wireless energy supply for an MAV propulsion system using microwave was developed. This system consists of three sub system; the transmitter system, the rectenna system, and the tracking system. In the transmitter system five horn antennas were used as the antenna elements for the phased array system and both the beam divergence and steering angle was about 9deg. Eight rectennas were arrayed in parallel to obtain enough power to drive the electric motor on the MAV(the voltage was 250mV and the current was 6.8mA) in rectenna system. In tracking system two units of antenna system with leaf pattern which received the linearly-polarized wave despite the MAV yaw angle were set in each axis(x, y) for tracking an MAV in a 2-Dimentional space. And three output voltages $V_{com},\;V_1$ and $V_2$ were loaded in the PC to detect if the distance between transmitter and receiver was not constant. Finally when the microwave beam was steered by the phased array system the output voltage from rectenna was measured at 62cm while the MAV circled around above the transmitter system.

• 전력전자학회논문지
• /
• 제19권6호
• /
• pp.572-581
• /
• 2014

A design and control method of DC/DC converter, which can control variable DC-link voltage to drive a fuel cell electric vehicle (FCEV), is proposed in this study. Given that a fuel cell has low-voltage and high-current characteristics, the required voltage for operating motor must be output through the DC/DC boost converter in the system to drive an FCEV. The proposed converter can choose the output voltage of battery or fuel cell in consideration of the driving mode, as well as control DC-link voltage in accordance with the back electromotive force. The switching lag-time to prevent shortage of pulse-width modulation inverter arms makes distorted current waveform caused by voltage distortion. Through this control method, the proposed converter can reduce the output voltage distortion and current ripple of the inverter, thereby reducing the distorted torque. Simulations and experimental results are presented to verify the reliability of the proposed DC/DC converter.

• 환경위생공학
• /
• 제12권3호
• /
• pp.41-49
• /
• 1997

In South Korea since 1970s the rapid development of economic growth has brought about "Urbanization" in many areas and also raised the level of people's life in many ways. At the same time, however, the industrialization and overpopulated districts in many areas have caused the problems of air pollution in necessary. Among those air pollution, in particular, in large cities has become more serious since 1990s than before. Air pollution, like TSP and SO$_{x}$ caused by heating, generation of electric power and industrialization in 1980s, showed as that of the type of an underdeveloping country and was not hazardous enough to people in the least. Unfortunately, in 1990s NO$_{x}$, CO and O$_{3}$ caused by the soaring numbers of many types of cars have exhausted air pollutant more hazardous as the same air pollution type of many developed countries. So, the purpose of this study would be to analyze the changes of concentration of NO$_{x}$ and CO on environmental air by traffic volume and from the side drive way to the degree of distance in Sungnam City, and recognize the citizens' consciousness to air pollution and suggest the best walking point in part, and plan to design the reasonable use of cars and finally make the air quality improve toward the better-ment in part. From the research result we can know that people walking in the street would be protected from the hazardous air pollutant caused by the cats if they walk apart from a drive way as far as they can in the street. Accordingly, it might, to minimize th affect of air pollution, be thought to be desirable that the consideration of in introduction the system that the vehicle using the diesel engine motor should use the centered-lane aparted from road. Another to be desirable is that along side the road, the trees inhaled the pollution should be planted.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.96-105
• /
• 2013

This paper presents a standardization method for designing wire harness systems, based on the control types and functional blocks, for use in commercial vehicles. With a rapid increase in the installation of systems with added new features, it is very important to develop a reliable wire harness design in a short time by standardizing wire harness designs and reusing the standard design. Because the function of a system, particularly, for commercial vehicles, varies significantly on the basis of the requirements, regulations, and options, it is not effective to establish one standard design for one system. In addition, a system with the same function may differ in terms of the input conditions and output loads on the basis of the installed vehicle types, and it is not practical to standardize a harness design targeting an entire system. In this study, the wire harness designs of a system were classified into six categories based on the control types of the system: switch driven, control of a switch, control of an electronic control unit, unit driven, control of a unit, and connector operation. Then, a wire harness design of each system was divided into three blocks according to their functions: the control, drive, and monitoring blocks. The standard wire harness designs were made for each functional block of each control type. The advantage of this proposed method is that an effective and practical design can be obtained, which covers the diversities in the same system for different grades of commercial vehicles with a reduction in the number of wire harness supplements.

• 한국항행학회논문지
• /
• 제16권6호
• /
• pp.1123-1133
• /
• 2012

논문에서는 극저속 영역 및 저속 영역에서 안정적이고 동특성이 우수한 벡터제어 시스템을 구성하여, 축소차원 상태관측기를 이용한 순시속도 관측기와 극 저속 제어, 회전자 속도를 추정하는 벡터제어 시스템에 관한 방법을 제안하였다. 본 시스템에서 제안된 관측기는 축소차원 상태관측기를 부하토크 추정에 적용하여 속도추정에 이용함으로서 시스템구성을 간단히 구현 하면서도 극 저속 영역에서 정확한 순시속도 추정이 가능하였다. 또한, 시스템 잡음에 의한 영향을 줄이고, 관측기의 극을 변화시키는 일 없이 부하외란 이나 모델화 오차, 측정 잡음 등에 강인한 유도전동기 속도제어 시스템을 제시하였다.

• Journal of Biosystems Engineering
• /
• 제38권4호
• /
• pp.255-263
• /
• 2013

Purpose: It is not easy to drive a rice-transplanter avoiding underlapped or overlapped transplanting in paddy fields. An automated guidance system for the riding-type rice-transplanter would be necessary to operate the rice-transplanter autonomously or to assist the beginning drivers as a driving aid. Methods: A prototype of guidance system was composed of embedded computers, RTK-GPS, and a power-steering mechanism. Two Kalman filters were adopted to overcome sparse positioning data (1 Hz) from the RTK-GPS. A global Kalman filter estimated the posture of rice-transplanter every one second, and a local Kalman filter calculated the posture from every new estimation of the global Kalman filter with an interval of 200 ms. A PID controller was applied to the row-following mode control. A control method of U-turning mode was developed as well. A stepping motor with a reduction gear set was used to rotate the shaft of steering wheel. Results: Test trials for U-turning and row-following modes were done in a paddy field after some parameters have been tuned at the ground speed range of 0.3 ~ 1.2 m/s. The minimum RMS error of offset was 3.13 cm at the ground speed of 0.3 m/s while the maximum RMS error was 13.01 cm at 1.2 m/s. The offset RMS error tended to increase as the ground speed increased. The target point distance, LT also affected the system performance and PID controller parameters should be adjusted on different ground speeds. Conclusions: A target angle-based PID controller plus stationary steering angle controller made it possible for the rice-transplanter to steer autonomously by following a reference line accurately and even on U-turning mode. However, as condition in paddy fields is very complicated, the system should control the ground speed that prevents it from deviating too much due to ditch and slope.

• 한국정보통신학회논문지
• /
• 제18권9호
• /
• pp.2237-2242
• /
• 2014

전 세계적으로 통신발달, 수명연장 등의 이유로 1인 가구가 급증하고 있으며 그에 따라 고독사 등의 문제점이 발생하고 있다. 이러한 문제점을 해결하고 사생활 침해가 없이 혼자서도 건강한 삶을 유지할 수 있도록 본 논문은 IR-레이더 및 레이저 변위센서를 이용하여 원거리 비접촉 생체신호 측정이 가능한 시스템을 제안하였다. 제안된 시스템은 원거리에서 비접촉으로 생체신호를 측정하는 방법으로, 실내 위치추적을 위한 IR 레이더 시스템과 비접촉 생체신호 측정을 위한 변위센서, 그리고 센서를 목표지점으로 이동하는 구동부로 구성되며 기존의 1m에 불과하던 생체신호 측정거리를 8m이상으로 늘릴 수 있는 시스템이다. 제안된 시스템을 실험을 통하여 타당성을 검증한 결과 정상적으로 측정이 가능하였다.

• 드라이브 ㆍ 컨트롤
• /
• 제19권4호
• /
• pp.36-45
• /
• 2022

The aim of this study was to verify an E-driving system of a 44 kW-class electric tractor using agricultural workload data. Workload data were acquired during field test (plow tillage, rotary tillage, loader operation, field driving, asphalt driving) using a conventional tractor with a load measurement system. These workload data were converted to data of a 44 kW-class tractor based on the load factor of the engine. These data were used to verify the design of the E-driving system of an electric tractor. High-load operations such as plow tillage, rotary tillage, and loader operation could be performed at stage L and stage M. High-speed operation (asphalt driving) could be effectively performed at stage H using a rated rotational speed of the motor. As a result, the E-driving system of the electric tractor was possible to perform all major agricultural operations according to gear stages of range shift. Based on results of this research, we plan to develop an electric tractor equipped with an E-driving system and conduct research on actual vehicle verification in the future.

• 전자공학회논문지T
• /
• 제36T권1호
• /
• pp.51-57
• /
• 1999

본 논문은 온도센서 RSD. Pt 100Ω의 감지신호가 Temperature Controller의 릴레이 출력을 발생시키고 PLC 입력접점으로 입력시켜 1Scan Time으로 연산된 PLC 출력을 접점 P030에 Interface Unit를 연결시키므로 부하를 구동시키는 개발장비인 Wired Logic Type Unit에 대해서 기술하였다. 현재 PLC 교육장에서 프로그램 되어진 PLC가 부하를 구동시킬 수 있는 국내의 교육 PLC Test Kit로는 PLC와 부하 사이에 Interface 과정이 무시된 상태에서 PLC의 교육을 하도록 되어있다. 개발 키 트는 이 점을 보안하기 위해서 각종 센서 중 전자에서 언급한 온도 센서 Pt 100Ω을 이용한 온도 제어기의 릴레이 출력이 PLC 입력으로 피드백 되었을 때, 연산된 PLC 출력접점에 WLTU를 삽입시켜 PC, PLC와 부하 사이에 실시간 시스템으로 구동 시킬 수 있는 설비로, PLC 사용의 핵심원리를 쉽게 이해하고 알아 볼 수 있었다. 부하 Interface Unit인 WLTU의 구성은 구동 부분인 유 접점, 무접점, 센서, 지시 등, A접점, B접점 부하인 Motor로 나누었다.